HOW TO ENTER TO SERVICE MODE AKIRA CT-29AZ9 AND CIRCUIT DIAGRAM

AKIRA CT-29AZ

CRT TV

SERVICE MODE AND CIRCUIT DIAGRAM 

CHASSIS ADJUSTMENT
1. EEPROM partial initializing
1.1. Go to the function set menu (there are two methods: a / b) Press 'VOL+' key and 'VOL-' key on the control board at the same time and switch on power switch, then go to the function set menu. After TV is on, press "factory" key  twin then go to the function set menu.
1.2. Press 'PM' key and 'SM' key on the control board at the same time until the “INITIAL PART OK” appears, this means the memory having been partially initialized. Operate repeatedly if the picture has no change.

** All of the TV set EEPROM must be partially initialized before ex-factory or after change of the Chroma IC NN5198 / NN5199 or fully EEPROM initialized after change of the EEPROM 24C04 (OR 24C08,24C16 ).
Do a search and store.
2 .COMPLETE MACHINE GENERAL ADJUSTMENT
2.1. Screen Voltage Adjustment.
2.1.1. Press 'screen' key (See Note 1);
2.1.2. Adjust the screen knob of FBT to get a horizontal faintness beam line;
2.1.3. Press 'screen' key again or 'stand by' key to go to the normal work status;
2.2. Focus Voltage Adjustment.
2.2.1. Receive monoscope pattern. Set picture mode to standard status;
2.2.2. Adjust the focus knob of FBT to get the clearest sharp picture.
2.3. Horizontal Centering Adjustment
2.3.1. Receive monoscope pattern;
2.3.2. Press 'factory' key (See Note 1) one time and go to system parameter adjustment menu;
2.3.3. Press 'MENU' key, go to horizontal and vertical parameter adjustment menu;
2.3.4. Select 'H' POSITION by pressing 'PROG+' key and 'PROG-' key. Press 'VOL+' key and 'VOL-' key to adjust the horizontal center of the pattern at the center of CRT screen.
2.3.5. Exit system parameter adjustment menu by pressing 'factory' key twin.
2.4. PAL System Vertical Pincushion Adjustment
2.4.1. Receive PAL system cross hatch pattern signal;
2.4.2. Press 'factory' key one time, go to system parameter adjustment menu;
2.4.3. Press 'MENU' key, go to horizontal and vertical parameter adjustment menu;
2.4.4. Select 'V LINE' and 'V SCURVE' by pressing 'PROG+' key and 'PROG-' key; press 'VOL+' key and 'VOL-' key and adjust corresponding parameter to obtain picture's vertical pin cushion a good status PAL system
2.5. Vertical Size and Vertical Center Adjustment
2.5.1. Continue operation 3. Select 'V HEIGHT" and 'V POSITION', press 'VOL+' key and 'VOL-' key adjust corresponding parameter to obtain picture's vertical size and vertical center adjustment a good status.
2.5.2. Exit system parameter adjustment menu by pressing 'factory' key twin.
2.6. White Balance Adjustment
For Factory Auto Computer adjustment
2.6.1. Receive white balance test signal;
2.6.2. Set picture "MILD" mode.
2.6.3. Insert the special plug into CN002, press adjustment key which belongs to white balance adjustment equipment and go to auto white balance adjustment;After adjustment well, remove the plug.
For Factory Auto Computer adjustment
2.6.4. Press 'factory' key one time and go to system parameter adjustment menu;
2.6.5. Press "MENU" key once, then go to the White Balance adjustment menu;
2.6.6. Press ‘Prog +' key and 'Prog -' key to select the R, G, B cutoff and R, B Driver.
2.6.7. Press 'VOL+' key and 'VOL-' key to change. Or using the below direct key
2.6.8. Key: 0 for SUB-BRIGHT, 1 for CUTOFF-R, 2 for CUTOFF-G,
3 for CUTOFF-B, 4 for DRIVER-R, 5 for DRIVER-B Recall for toggle the Sub-Bright adjustment (Min. contrast, some CPU version do not work)
2.7. Sub-bright Adjustment
2.7.1. Receive PHILIPS signal;
2.7.2. Set picture "RICH" mode.
2.7.3. Press 'factory' key one time and go to system parameter adjustment menu;
2.7.4. Press digital key '0', select 'SUB-BRIGHT';
2.7.5. Press 'VOL+' key and 'VOL-' key until Grey scale signal can be seen;
2.7.6. Exit system parameter adjustment menu by pressing 'factory' key twin.
2.8. RF AGC Adjustment
2.8.1. Receive 60dBuV monoscope pattern;
2.8.2 Press 'factory' key one time and go to system parameter adjustment menu;
2.8.3 Press 'PROG+' key and 'PROG-' key, select 'RF AGC';
2.8.4 Press 'VOL+' key and 'VOL-' key to change the value of 'RF AGC' until picture's noise disturbing just disappears ;
2.8.5. Exit system parameter adjustment menu by pressing 'factory' key twin.
2.9. NTSC System Horizontal and Vertical Adjustment
2.9.1. Receive NTSC system cross hatch pattern. Adjust same as PAL system.
2.10. Warm up mode
2.10.1. Switch on power switch and Press 'factory' key one time; switch off power switch and switch on power switch again, at this time there is no signal white raster and TV won't switch off automatically. TV receiver can be sent to warm up line.
2.10.2. Before exit warm up line, press 'factory' key three times continue, at this time exit warm up mode, there is no signal and the LOGO ‘AKIRA’ pattern will appear.
NOTES:
1. Connect the remote IC PIN7 and PIN16 through a jiggle switch on the USER remote handset , this switch is defined as "screen" key; Connect the remote IC PIN8 and PIN16 through a jiggle switch on the USER remote handset , this switch is defined as "factory" key,
2. On the product line's alignment service we must use special memorizer that has been well written with respective correct version data.
3. If having no special memorizer that has been well written with data when servicing out of factory, we can use blank new EEPROM. Then the new EEPROM will be automatically totally initialized with default data after main power switch is on. Most parameters are free-alignment after initialized; only need adjust the several parameters of function set parameter and system parameter adjustment menu.
4. If no blank new EEPROM or no special memo rizer that has been well written with data, we can use memorizer that has been written with old data instead, but must be totally reinitialized; the operation is as following:
a) After TV is on, press "factory" key twin­then go to the function set menu;
b) Press 'AV/TV' key and 'P.M' key on the control board, the TV turns off automatically; this means the memory having been totally initialized. Operate repeatedly if the picture has no change;
c) Switch off and exit;
d) After initialized, adjust the several parameters of function set parameter and system parameter adjustment menu.
5. The parameters of function set parameter and system parameter adjustment menu mustn't be adjusted;
* Ensure no adjustment on the following parameter except those parameter mentioned in this manual:-
a) System parameter adjustment menu (This is coming from the NN5198/ NN5199)
AFT
VIF VCO
H VCO
VIFDET NEG
VIFDET INT
VIFDET EXT
b) The ninth digital and the tenth digital of function set parameter These parameters must be IC interior values. If the above parameters have been changed, we must partially initialize the EEPROM.
6. Two different initializing
a) Fully initialize: initialize the EEPROM's most work data and preset default value. Including: work parameter of NN5199, horizontal and vertical parameter, OPTION parameter (via. function set parameter), picture mode parameter, volume mode parameter and white balance parameter.
b) Partially initialize: only initialize work parameter of NN5199 and the ninth digital and the tenth digital of function set parameter(via. ISUD0, ISUD1,ISUD3,ISUD4,ISUD5),preset as interior values.
7. If use 25” or above Pure Flat tube, adjustment of horizontal size and pincushion distortion must be done as follows :
a) Receive 60dBuV PAL system monoscope pattern;
b) Press 'factory' key one time and go to system parameter adjustment menu;
c) Press 'MENU' key and select ' Position Menu ' as below
V POSITION for adjust vertical position 00 to 07
H POSITION for adjust Horizontal position 00 to 1F
V EHT for adjust vertical shape 00 to 0F
H EHT for adjust Horizontal shape 00 to 0F
d) Press 'MENU' key and select ' geometry Menu ' as below;
V-AMP for adjust vertical size 00 to 7F
V_LINE for adjust vertical linearity 00 to 3F
V_SC3 for adjust vertical S-correction X3 00 to 3F
H-AMP for adjust Horizontal size 00 to 3F
EW-PARA for adjust Pincushion 00 to 3F
EW-COR for adjust Pincushion corner 00 to 0F
TRAPEZ for adjust trapezium 00 to 3F
V_SC5 for adjust vertical S-correction X5 00 to 0F
e) Receive 60dBuV NTSC system monoscope pattern; Repeat the above step 7.2 to 7.4.
f) Exit system parameter adjustment menu by pressing 'factory' key twin.
COLOUR PURITY AND CONVERGENCE ADJUSTMENT
COLOUR PURITY ADJUSTMENT (See Fig.1)
BEFORE ANY ADJUSTMENTS DESCRIBED BELOW ARE ATTEMPTED,V-HIGH, B+
VOLTAGE AND FOCUSING ADJUSTMENT MUST BE COMPLETED.
1. Place the TV receiver facing NORTH or SOUTH.
2. Plug in TV receiver and turn it on .
3. 3.Operate and warm-up the TV receiver at least over 30 minutes.
4. Fully degauss the TV receiver by using an external degaussing coil
5. Receive a crosshatch pattern and adjust the static convergence control roughly.
6. Loosen the clamp screw of the deflection yoke and pull the deflection yoke towards you.
7. Enter into ADJUST MENU .set the values of C-R,C-G,C-B to “00”.
8. Adjust the purity magnets so that green field is obtained at the center of the screen.
9. Slowly push the deflection yoke toward bell of CRT and set it where a uniform green field is obtained.
10. Tighten the clamp screw of the deflection yoke.
CONVERGENCE ADJUSTMENT (See Fig.1)
1. Receive a dotted pattern.
2. Unfix the convergence magnet clamped and align red with blue dots at the center of the screen by rotating (R,B) static convergence magnets.
3. Align Red/Blue with green dots at the center of the screen by rotating (RB-G) static convergence magnet.
4. Fix the convergence magnets by turning the clamped.
5. Remove the DY wedges and slightly tilt the deflection yoke horizontally and vertically to obtain the good overall convergence.
6. Fix the deflection yoke by wedges.
7. If purity error is found, follow “PURITY ADJUSTMENT” instructions.

CIRCUIT DIAGRAM 
CLICK ON THE IMAGES TO SOON IN


FINAL INSPECTION AND ELECTRICAL FUNCTIONAL CHECK
1. CHECKING THE ELECTRICAL FUNCTION:-
1. Connect the power cord and connect the signal to RF input.
2. Check the power supply whether OK or not. Switch on the TV set and the LED is on. Switch off the TV screen and should not have CRT spot within 3 sec.
3. Receive the channel 1 for monoscope pattern to check the picture focus and the round circle should not be distorted. The centre position, and VOS line/size are within spec. Check the brightness, contrast and colour condition. Check the convergence, picture must be clear, focus OK and white balance are OK. Also check the complete screen picture quality. High voltage condition OK and the Screen picture must be OK.
4. Check all the functional keys must be working well.
5. Receive colour pattern signal and the system colour. (PAL/SECAM/NTSC). Check the power main on/off switch, brightness, volume, colour, contrast and tint. The picture quality must not have colour noise, unbalance size and distorted condition.
6. Check the sound quality standards, Volume up/down are OK to spec, and sound output. Ensure the sound output is not distorted and noisy. No interference for DK/BG/I/M.
7. Use remote Control Unit for all types of function check and ensure OK.
8. Check the words display condition.
9. Shock test and make sure the picture and sound are not distorted and shifted.
10. Use strong and weak signal to check the colour picture condition. After adjust the signal level to 35-40 dB and the colour should not gone. The picture and sound must be OK. At 60 dB the picture should not have snow noise.
11. Ensure the factory mode setting are set. Set-off the factory mode function and last switch off the TV set.
12. All the “NG” sets must send for repairing and recording for reference.
13. Check the AV input and output the picture and sound must be OK.
2. RELIABILITY AGING TEST:-
1. 1st lot of production sets. Sampling 20 sets for aging 7 days continues test with colour signal in. Normal production sets must be age for 1 day.
3. MECHANICAL INSPECTION:-
1. Inspect all glue are firmly placed.
2. Check all screws are tightened, no missing and loose.
3. Check all the connectors are fully located onto the chassis base.
4. Check all the safety components are firmly located onto the chassis and no damage.
5. The TV internal side should not see any excess metal materials.
6. Check all the cable and wire are OK in-used.
7. Check the FBT and switching transformers not high mounting. The big capacitor are not slanting and high mounting.
4. HIGH POTENTIAL TESTING:-
1. Set the mega-meter is set in position.(Insulation tester)
2. Set the meter to DC500V.
3. Use the meter probe onto the tuner body and the power cord on connector socket.
4. Switch on the button and test the insulation performance and the reading at 2/3 position.
5. Insulation spec must over 9.0 Mohm. if not reject.
Note: Everyday work check the high pot. Condition as 3100V, 10 mA, 5 sec are OK.
5. SAFETY CHECK:-
1. High voltage checking. Use high pot tester and set the tester to 3100V, 10mA and ensure the AC/DC switch is in AC position. Set the tester to 10mA and timer to 5 sec. Test all naked metalof the TV and ensure no arcing and sparking.
2. Checking methods.
- connect the power cord into power socket.
- the high pot tester gun pointed at metal part of TV set body.
- switch on the switch to test the high electric power.
- connect with high voltage within 5 second and remove the tester gun point.


SHARP LC-46X20E SERVICE MODE AND HOTEL MODE

SHARP BLU RAY

SHARP LC-46X20


SERVICE MODE AND HOTEL MODE  

Public Mode (Hotel Mode)
1. Starting the Public Mode
• There are two following ways to display the PUBLIC Mode setting screen.
1) On the process adjustment mode screen (2/33), set the “HOTEL MODE” Flag to ON. Turn off the power, and turn it on again, pressing the CHANNEL UP and VOLUME UP keys of the main unit at the same time.
2) Enter the Pass Word, and start the unit.
a) Turn on the power, pressing the INPUT and VOLUME UP keys of the main unit at the same time.
b) Display the Pass Word input screen.
Operation procedure
• The initial input position is the digit at the left end.
• For the numeric keys 0 to 9 of R/C, key input is accepted. Input of the other keys is prohibited.
• Change “-” to “*” by inputting the numeric key at the input position, and shift the input position rightward one digit.
• When three digits are completely input, the Pass Word is judged.
c) Check the Pass Word by inputting three digits.
If the Pass Word is 027 , it shifts to the PUBLIC Mode setting screen.
In another case, the screen is erased, and it operates in the ordinary mode.
Exiting the Public Mode screen
• There are two following ways to exit the Public Mode setting screen.
1) Turn off the power.
2) Select “Execution” in the PUBLIC_Mode to execute it.
Activate the restart under the set content. Here, the START input SOURCE setting is excluded since this item is referred to only when the power is turned on.
3. Set value of the Public Mode
• Each set value in the PUBLIC Mode is initialized when the factory setting is applied.
(The setting of the PUBLIC MODE Flag in the process adjustment mode screen is not changed.)
Operation after “RESET”
Select “RESET” in the PUBLIC Mode, and it operates as follows when it is executed (refer to the basic operation).
• The set contents in the PUBLIC mode are initialized.
• It does not exit the PUBLIC mode.
• PUBLIC MODE Flag does not change. (It is not set to OFF.)
Adjustment method after PWB and/or IC replacement due to repair
The unit is set to the optimum at the time of shipment from the factory. If any value should become improper or any adjustment is necessary due to the part replacement, make an adjustment according to the following procedure.
1. Procure the following units in order to replace the main unit, IC3301, IC8101, IC3501, IC3502, IC8301, IC8302, IC8303, or IC8304.
MAIN UNIT: DUNTKE186FM01 (LC-42/46/52XL2E)
DUNTKE186FM02 (LC-46/52XL20E)
NOTE: [Caution when replacing ICs in the main unit (IC1501/IC1502/IC1503/IC2002) or the mini av unit (IC802)]
The above ICs are EEPROMs storing the EDID data of HDMI and the monitor microcomputer. Before replacing the relevant part, procure the following parts in which the data have been rewritten.
IC2002 RH-IXB986WJN8Q Monitor microcomputer
IC802 RH-IXC284WJQZS HDMI_EXT4
IC1501 RH-IXC285WJQZS HDMI_EXT5
IC1502 RH-IXC286WJQZS HDMI_EXT6
IC1503 RH-IXC287WJQZS RGB (PC)_EXT7
2. After replacing the LCD panel or LCD control PWB, check PANEL_SIZE in the following procedure.
1) Enter the process adjustment mode.
2) Use the cursor keys UP /DOWN  and P UP/DOWN of R/C to select the item [PANEL_SIZE] on the page 33/33.
3) Verify that the panel size is displayed.
4) If the size doesn't match, select the values of the panel size with the Vol UP/DOWN keys.
5) After selection in Step 4), press the OK key, and it is completed with OK displayed.
3. After replacing the LCD panel or LCD control PWB, adjust the VCOM in the following procedure.
1) Enter the process adjustment mode.
2) Use the cursor keys UP/DOWN and P UP/DOWN of R/C to select the item [VCOM ADJ] on the page 10/33.
3) Press the OK key to verify that the adjustment pattern is displayed.
4) Use the +/- keys of VOL of L/C to adjust the flicker in the center of the screen to minimum.
5) When the optimal state is achieved in Step 4, press the OK key to turn the pattern to OFF.
4. After replacing LCD panel or LCD control PWB, perform the up/down brightness difference adjustment in the following procedure. (Note: It is applicable to LC-42/46/52XL2E only.)
1) Enter the process adjustment mode.
2) Use the cursor keys UP/DOWN and P UP/DOWN of R/C to select the item [LCD_LUMA_ADJ] on the page 10/33.
3) Press the OK key to verify that the adjustment pattern (all gray) is displayed.
4) Use the VOL +/- keys of R/C to adjust the upper/lower brightness difference in the center of the screen to minimum.
5) When the optimal state is achieved in Step 4, press the OK key to turn the pattern to OFF.
NOTE: LCD LUMA UD **< The value at the ** part is changed.
LCD LUMA DOWN 0 (Note that the value is changed if the P UP/ DOWNkeys are pressed in Step 4 above.)
Entering and exiting the adjustment process mode
1. Press the “POWER” key on the set of running TV set to force off the power.
2. While holding down the “VOL (-)” and “INPUT” keys on the set at once, plug in the AC power cord to turn on the power. The letter “K” appears on the screen.
3. Next, hold down the “VOL (-)” and “P (V)” keys on the set at once. Multiple lines of character string appearing on the screen indicate that the set is now in the adjustment Process mode. If you fail to enter the adjustment process mode (the display is the same as normal startup), retry the procedure. (Another procedure)

4. Press the “MENU” key on the main unit to display OSD.
5. Move the cursor to SERVICE (OSD) using the cursor keys on the remote control.
Then press the “MENU” key on the remote control to enter the service mode (adjustment process mode).
6. To exit the adjustment process mode after the adjustment is done, unplug the AC power cord to force off the power. (When the power is turned off with the remote controller, once unplug the AC power cord and plug it in again. In this case, wait 10 seconds or so before plugging.)
CAUTION: Use due care in handling the information described here lest the users should know how to enter the adjustment process mode. If the settings are tampered with in this mode, unrecoverable system damage may result.
Lamp error detection
1. Function
This LCD color TV set incorporates a lamp error detection feature that automatically turns off the power for safety under abnormal lamp or lamp circuit conditions. If by any chance anything is wrong with the lamp or lamp circuit or if the lamp error detection feature is activated for some reason, the following will result.
1) The power is interrupted in about 6 seconds after it is turned on.
(The power LED on the front of the TV set turns red from green and keeps blinking in red: ON for 250 ms and OFF for 1 sec.).
2) If the above phenomenon 1) occurs 5 times consecutively, it becomes impossible to turn on the power. (The power LED remained red).
2. Measures
1) Checking with lamp error detection OFF
Enter the adjustment process mode, referring to 1. Entering and exiting the adjustment process mode. If there is a problem with the lamp or lamp circuit, the lamp will go out. (The power LED is green.) Then, you can check the operation to see if the lamp and lamp circuit are in trouble.
2) Resetting the lamp error count
After the lamp and lamp circuit are found out of trouble, reset the lamp error count. If a lamp error is detected five consecutive times, the power cannot be turned on. Using the cursor (UP/DOWN) key, move to the cursor to [LAMP ERROR RESET], Line 8 on adjustment process mode service page 2/33. With the cursor (LEFT/RIGHT) keys, select the [LAMP ERROR RESET] value. Finally press the cursor (OK) eys to reset the value to “0”.




LCD - LED – PLASMA AND CRT

LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT



LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT



LCD - LED – PLASMA AND CRT



LCD - LED – PLASMA AND CRT



LCD - LED – PLASMA AND CRT




LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT




LCD - LED – PLASMA AND CRT




LCD - LED – PLASMA AND CRT



HOW TO UPDATE THE SOFTWARE FOR AKAI LTC 32R5X3HCM

AKAI LTC 32R5X3HCM

SOFTWARE UPGRADE 

ATV SOFTWARE UPGRADE
A.Install software.
1.Copy folder of MSTAR ISP Tool(V4.xxx) to PC. mAdvice to English WINDOWS XP
.
2.Install MSTAR Driver from folder FTC100103 (MSTAR Driver). commonly,Install automatically  after it connect the Update Adaptor Board to PC.You operate by cue.It will install total 3 SYS type drive files.
B.Update
1.Turn off the TV
2.Conect the Update Adaptor Board to VGA socket
of TV and PC.
3.Run software of ISP_Tool V4.xxx.exe.
4.Turn on the TV.Wait Connecting communications, muntil it display "Device Type....".
5.When if it can't diplay frondose type device, you can turn off the TV,then turn on the TV again.Or press connect item on top of software menu mfo r connecting communication again.
6.Press to confirm Read item on top of software  menu.
7.Press to confirm Read item, select updating fils.
8.Press to confirm AUTO item on top of software  mmenu.
9.Change the selected option item as the same as this picture.
10.Press Run item,start updating.
11. Finish updating until it display PASS.
Warning: don't turn off the TV in Updating!
Note
:This software need restoration after update.
DVB-T SOFTWARE UPGRADE
1.Delete all files in USB,and Copy update file of "zr39 160.img” into USB,but you don't rename the file.
2.Turn off the TV.
3.Connect USB Jack to CN21 Jack of Main board.
4.Turn on the TV, then select INPUT into DVB-T if  input isn't DVB-T state.
5.DVB-T is Loading.
6. Build update.
7.Update is finished after DVB-T automatically  run newly.
Warning: don't turn off the TV while it is Updating!
Note:This software need restoration after update.
DVD SOFTWARE UPGRADE
1.Del all files in USB.
2.Copy update files into USB,the file name must be MTK.BIN.If it isn't this file name, this file name must be rename to MTK.BIN.
3.Turn on the TV Combo,select working in DVD input,and take out all disc and take out all USB and take out all CARD.
4.Insert USB with update file,select reading USB.
5.After it read update file,it have prompt on TV Combo,then you must operate according to prompt.If it is automatically Updatting,please can't do any operation,If it have cue that you press play key to continue update,please press play button on R/H to update.
6.You can't do any operation while updatting,until TV-Combo restart DVD working screen, Update is finished,then you take out USB.
Warnning:you can't do any operation while updatting,and it can't quit DVD working! If update is discontinuuty,DVD will not work.
Note:This software need restoration after update.
ATV(9E19)
A.SOFTWARE DATA'S RESTORATION
1.Enter system setting item of MUNE.
2.Select memory recall item,press right button for default setting.
B.SOFTWARE DATA'S ADJUSTMENT
1.press MENU button,then input 1234 numbers to enter factory menu by RH.
2.press to select into factory reset item by RH,and press right button,get back all inner data to default data,adjustment's data isn't reserved.Press Menu button again to exit factory menu.
3.press to select other item,the press right button,it can enter this item data adjustment state. There may be adjustment data
DEFAULT VALUE ADJ
You press MENU button to exit factory menu by RH
,and data is automatically saved.When if select into Factory Reset item,then press right button,it get back inner data into default data, and manual adjustment data isn't saved.
Note:don't optionally adjust default data,TV can't work if data is error.
DVB-T(ZR39160)
1.Enter DVB-T menu,select system setting item,then press OK button enter setting.
2.Select factory default item,press OK button to enter it,then select Restor to Default item,press OK button enter setting.
3.Press OK button enter Restor.
DVD(MTK1389L)
1.Select DVD of INPUT.
2.Press DVD setup to enter DVD setup menu.
3.Select Preference Page,then select Default,then press OK button to reset.
MST9E19A SCHEMATIC 
CLICK ON THE IMAGE TO ZOOM IN





LCD - LED – PLASMA AND CRT

LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT



LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT



LCD - LED – PLASMA AND CRT



LCD - LED – PLASMA AND CRT



LCD - LED – PLASMA AND CRT




LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT




LCD - LED – PLASMA AND CRT




LCD - LED – PLASMA AND CRT