Friday, September 18, 2015

MUTOH VALUEJET 1204 ERROR CODES AND CAUSES

MUTOH VALUEJET 1204

ERROR CODES AND CAUSES 

CPU SYSTEM SERIOUS ERRORS
E016 ­ Interrupt [00] 
 Interruption exception error
E016 ­ TLB Modif [01] ­
Command border exception/TLB exception
E016 ­ TLB­L/I [02] ­
Data border exception/TLB exception
E016 ­ TLB­S [03] ­
Data border exception/TLB exception (store) error
E016 ­ AddErr­L/I [04]
­ Address exception error (load or command fetch)
 E016 ­ AddErr­S [05] ­
Address exception error (store)
E016 ­ BusErr­I [06] ­
Pass exception error (command fetch)
E016 ­ BusErr­L [07]
Bus exception error (load or store)
E016 ­ SystemCall [08] ­
System call exception error
E016 ­ BreakPoint [09]
Break point exception error
E016 ­ Reserverd [10]
­ Reserved command exception error
E016 ­ Copro [11]
­ Coprocessor disabled exception error
E016 ­ Overflow [12] ­
Arithmetic overflow exception error
E016 ­ Trap [13] ­
Trap exception error
E016 ­ Floating [15] ­
Floating point exception error
E016 ­ WatchDog [32] ­
Watchdog time­out exception error
E016 ­ Abort Err [33] ­
Abort error
MECHANICAL SERIOUS ERRORS
E065 ­
PF motor ­ Abnormal condition in PF motor (X­axis)
E066 ­
CR motor ­ Abnormal condition in CR motor (Y­axis)
E067 ­
PF encoder ­ Abnormal condition in media feed amount (X­axis)
E068 ­
CR encoder ­ Abnormal condition in head travel distance (Y­axis)
E069 ­
PF time­out ­ Time­out condition in media feed amount (X­axis)
E070 ­
CR time­out ­ Time­out condition in head travel distance (Y­axis)
E071 ­
PF overcurrent ­ Overload condition in PF motor (X­axis)
E072 ­
CR overcurrent ­ Overload condition in CR motor (Yaxis)
E074 ­
CR2 overcurrent ­ Overload condition in CR motor (Yaxis)
E075 ­
Head Cable ­ Abnormal condition in head cable or head thermistor.
E076 ­
Pre­heater system ­ Abnormal condition in pre­heater system
E077 ­
Platen Heat ­ Abnormal condition in platen heater system (thermistor, heater).
E078 ­
After Heat ­ Abnormal condition in after­heater system (thermistor, heater).
 E079 ­
Comm. ­ Abnormal condition in serial communication
E080 ­
Junction ­ Abnormal condition in serial communication
E081 ­
CR origin ­ CR_HP detection is not possible.
E082 ­
Wiper sensor ­ Abnormal condition in wiper sensor.
E084 ­
Head Dist. ­ Installed head is incorrect.
E085 ­
Head overheat ­ Abnormal condition in head driver.
E086 ­
Head OVP ­ Abnormal condition in head driver.
E087 ­
H Trans Th ­ Abnormal condition in head transistor.
E090 ­
Heater Volt. ­ The input voltage of AC inlet may be too high.
E097 ­
NVRAM ­ Abnormal condition in NVRAM