Sunday, September 13, 2015

PANASONIC TC-L32X1 - TC-L37X1 HOTEL MODE AND SERVICE MODE

PANASONIC TC-L32X1 - TC-L37X1 

HOTEL MODE AND SERVICE MODE 

HOW TO ACCESS HOTEL MODE
1. Purpose
Restrict a function for hotels.
2. Access command to the Hotel mode setup menu In order to display the Hotel mode setup menu, please enter the following command (within 2 second).
[TV] : Vol. [Down] + [REMOTE] : INPUT (3 times)
3. To exit the Hotel mode setup menu
Disconnect AC power cord from wall outlet.
MODES IN HOTEL MODE AND ITS DESCRIPTION
Item
Function
Mode

Select hotel mode off/on

Input






Select input signal modes.
Set the input, when each time power is
switched on.
Selection:
-/RF/Component/HDMI1/HDMI2/HDMI3/
Video1/Video2/PC
# Off: give priority to a last memory.


Channel








Select channel when input signal is RF.
Set the channel, each time power is switched
on.
Selection:
Any channel number or [-].
[-] means the channel when turns off.


Volume





Adjust the volume when each time power is
switched on.
Range:
0 to 100


Vol. Max




Adjust maximum volume.
Range:
0 to 100


OSD Ctrl





Restrict the OSD.
Selection:
OFF/PATTERN1
# OFF: No restriction
#PATTERN1: restriction


FP Ctrl






Select front key conditions.
Selection:
Off/Pattern1/All
# Off: altogether valid.
# Pattern1: only input key is valid.
# All: altogether invalid.



Pow Ctrl

Select POWER-ON/OFF condition when AC
power cord is disconnected and then connected.
OFF: The same condition when AC power
cord is disconnected.
ON: Forced power ON condition.

 HOW TO ACCESS IIC BUS LINE 
Self-check indication only:
Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [OK] button on the remote control for more than 3 seconds.
Self-check indication and forced to factory shipment setting:
Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote control for more than 3 seconds.
HOW TO EXIT
Disconnect the AC cord from wall outlet.
POWER LED BLINKING AND ITS CAUSES 
When an abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the
defective block can be identified by the number of blinks of the Power LED on the front panel of the unit

HOW TO ENTER TO SERVICE MODE OF THE TV
While pressing [VOLUME ( - )] button of the main unit, press [INFO] button of the remote control three times within 2 seconds.
WHICH KEYS TO USE TO NAVIGATE TROUGH THE SERVICE MENU
[1] button...Main items Selection in forward direction
[2] button...Main items Selection in reverse direction
[3] button...Sub items Selection in forward direction
[4] button...Sub items Selection in reverse direction
[VOL] button...Value of sub items change in forward direction ( + ), in reverse direction ( - )



LCD - LED – PLASMA AND CRT

LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT



LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT



LCD - LED – PLASMA AND CRT



LCD - LED – PLASMA AND CRT



LCD - LED – PLASMA AND CRT




LCD - LED – PLASMA AND CRT


LCD - LED – PLASMA AND CRT




LCD - LED – PLASMA AND CRT




LCD - LED – PLASMA AND CRT