Saturday, October 24, 2015

SONY BDP-S770 – BDP-S1700 SERVICE MODE

SONY BDP-S770 – BDP-S1700 

SERVICE MODE 

Enter Service Mode
The set disconnect AC, and Push front panel key ([OPEN/CLOSE] + [PLAY] + [STOP]) and AC IN  The keys will be released if the character of "SERVICE" displays on a front panel display. After that, the screen in service mode is displayed on a monitor.
Display Error Log
Error log is displayed.
The displayed logs can be saved in a USB memory.
Diag
The unit test of the device mounted on the MainBoard.
The unit test of the device mounted on the wireless board. (only wireless model)
Factory Initialize
Return all of the player setting to their factory defaults.
Caution: please check boot normally after that.
Network
Confirm Wired Network connection.
Version Up
The set updates by Update DISC.
System Information
System information of the set is displayed.
The Information on a soft version and drive information, etc. is displayed.

Service Mode Top Menu
It selects to each function from here.
output HDMI/Component 480p forcibly.
Operation
[1] Select and Activate Diag Menu.
[2] Select and Activate Log Menu,
[3] Select and Activate Factory Initialize Menu.,
[4] Select and Activate Network Menu
[5] Select and Activate Version Up DISC version Up Menu,
[6] Select and Activate System Information Menu.
[7] Select and Activate EMC Test Mode Menu. (not Used)
[8] Select and Activate Drive Menu.
[UP] Move Up cursor
[DOWN] Move Down cursor
[ENT] Activate the selected cursor.
*The cursor is not displayed when initial.
Front Panel Display
If cursor or arbitrary menu keys are operated,
the character will output to a front panel display, respectively.
*the character string.
initial display SERVICE
Diag S-DIAG
Log S-LOG
Factory Initialize : S-FINIT
Network : S-NET
Version Up : S-VUP
System Information : S-INFO
EMC Test Mode S-EMC
Drive : S-DRV
Diag Menu
(Window 1) Select test category
Operation
[LEFT] [RIGHT] Select Category
[DOWN][ENT] Activate the selected Category.
[RET] Return to Service Top Menu.
(Window 2) Device Test
After “Device Test” selects in window 1, the device to test is chosen.
Operation:
[LEFT][RIGHT] Select Device
[ENT] Activate and Start Test
[UP] Return to test category selection.
IF select IFCON, Move Up cursor. (see windows 3)
[DOWN] IF select IFCON, Move Up cursor. (see windows 3)
[RET] Return to test category selection.
>Test category list
Device Test
Video Test
Audio Test
Audio Input Test (not Used)
Wireless LAN Test (only Wireless Model)
>Device Test :Device List
USB Host USB Media Check (Front and Rear)
Only one time.
D/A Converter DAC write check (non-verification)
IFCON IFCON Test (see windows 3)
FDP all ON
Show Strings
LED Sequencial
FAN Control ON
Fan State (Display)
Diag Menu Video Audio test
(Window 1)Select Video Test Category
Operation:
[ENT] Activate and display Color Bar
[UP][RET] Return to test category selection.
(Window 2)Display Color Bar 
Operation
[ENT] Return to Select Video Test Category.
(Window3 ) Select Audio Test Category
Operation
[ENT] Play TONE Sound/Stop
[UP][RET] Return to Select Audio Test Category
>Video Test:
Color Bar output S terminal & composite & Component & HDMI.
>Audio Test;
TONE sound output ineOut(2ch)&/ SPDIF & HDMI.
 Diag Menu Wireless test
(Window 1)Select Wireless LAN Test Category
Operation:
[LEFT] [RIGHT] Select Category
[DOWN][ENT] Activate the selected Category.
[RET] Return to Service Top Menu.
(Window 2) Select Wireless LAN Test
Operation:
[1] Show Wireless LAN module Information
[2] Connect Access Point
[3] Start display RSSI value.
[4] Start Ping Test
[UP][DOWN] Select Test
[ENT] Activate and Start Test
[RET] Return to test category selection.
> Show WLAN HwInfo See Window 2)
Serial : Serial Number
Hard : Hardware Version
Mac Mac Address
> Connect to AccessPoint (See Window 3)
Connect Access Point only with the following AP settings.
Authentication method: NO-ENCRYPT
WEP key abcdef1234
SSID NETGEAR-DualBand-N
PMK ABCDE12345
IP: 192.168.1.10
Net mask: 255.255.255.0
Broadcast 192.168.1.255
When connect to AP, Status is “Connected!”
When cannot connect to AP, Status is “can’t Connect!”
> Start Display RSSI Value (See Window 4)
Display RSSI value.
> Start Ping Test (See Window 5)
Ping Test.
IP address use the value of “192.168.1.10”.
Error log
Display each contents of the Error log,
(Window 1) select log.
Operation

[1] Activate and Display Error log
[UP] Move Up cursor
[DOWN] Move Down cursor
[ENT] Activate the selected cursor.
[RET] Return to Service Top Menu.
(Window 2)
Display Error Log
Operation

[LEFT] Next Page
[RIGHT] Previous Page
[RET] Return to select log (window 1)
[RED] Write the contents of an error log on a USB memory.
Front Panel Display

select log Error Log
S-ELOG
Display Page display page ex) 001/050
>Log contents
Error Log

08/01/01 00:53:19: [ErrCode:080400000000]
[Date] [Time] [ErrCode]
**Write the contents of a log on a USB memory**
[RED] is pushed where a USB memory is inserted in a set in log display screen.
Please do not push the RED button immediately after USB memory is inserted.
Please do not pull out USB memory immediately after the RED button was pushed.
Error Log:
“getErrLogFile.trm” file is outputted in a USB memory.
Factory initialization
Return all of the player setting to their factory defaults.
(Window 1) select initialize.
Operation

When you return a set to the factory defaults, push [1] on this screen.
[1] Start Factory Initialize
[2] Start Factory Initialize for TV (not used)
[UP] Move Up cursor
[DOWN] Move Down cursor
[ENT] Activate the selected cursor.
[RET] Return to Service Top Menu.
(Window 2)
It is a screen of the end of initialization.
[RET] Return to Service Top Menu.
Please disconnect AC power supply, and connect AC again.
- The operation of other service mode menu can be continued.
Front Panel Display:
Initialize
SETTING
Initialize OK
INIT-OK (window 2)
Initialize NG
INIT-NG
Caution:
When “Quick Stand By” sets ON, The additional processes of AC IN and OFF are needed.
Please confirm the following processes for all sets.
1. Initialize (This command)
2. AC Off
3. AC In
4. Check FLD. If WAIT keep blinking, go to 5.else go to 8.
5. AC Off
6. AC In
7. Check FLD.
8. AC Off. (finish)
Drive
This menu is used to operate the drive using drive-related diagnostic
and tools.
Screen 1: Selecting items under *Service Menu
Screen 2: Selecting items under *Drive
Operations:
[UP] [DOWN] Move the cursor up and down
[ENT] Open the selected cursor item
[RET] Return to top menu
Test item list Display Panel
[1] Drive OP data Write : D-OPWRT
[2] Servo Parameter Check Menu : D-SEVPA
[3] Servo Signal Check Menu : D-SEVSG
[4] S-Curve Check Menu : D-SCUR
[5] Readability Check Menu : D-READ
[6] OP Position Check Menu : D-OPPOS
[7] OP Check Menu : D-OP
[8] Load Eject Aging : D-LOAD
[9] Spindle Control Check Menu : D-SPIND
[10] FA Test Mode : D-FAMOD
Screen 3: *Drive OP data Write
Purpose: Write OP data into flash IC
[UP] [DOWN] Move the cursor up and down
[ENT] Start the selected cursor item
[RET] Return to top menu
Remarks:
Mode 1 --> Basic & Entry model (BD modulation frequency 410Mhz)
Mode 1 --> Step Up model (BD modulation frequency 429Mhz)
Screen 4: *Servo Parameter Check Menu Not Use
Purpose: Verify servo parameter
[UP] [DOWN] Move the cursor up and down
[LEFT] [RIGHT] Move the cursor left and right
[ENT] Start the selected cursor item
[RET] Return to top menu
Screen 5: *Servo Signal Check Menu Not Use
Purpose: Verify servo signal
[UP] [DOWN] Move the cursor up and down
[LEFT] [RIGHT] Move the cursor left and right
[ENT] Start the selected cursor item
[RET] Return to top menu
Screen 6: *S-Curve Check Menu Not Use
Purpose: Verify S-Curve signal
[UP] [DOWN] Move the cursor up and down
[LEFT] [RIGHT] Move the cursor left and right
[ENT] Start the selected cursor item
[RET] Return to top menu
Screen 7: *Readability Check Menu Not Use
Purpose: Verify readability data
[UP] [DOWN] Move the cursor up and down
[LEFT] [RIGHT] Move the cursor left and right
[ENT] Start the selected cursor item
[RET] Return to top menu
Screen 8: *OP Position Check Menu Not Use
Purpose: Verify OP position
[UP] [DOWN] Move the cursor up and down
[LEFT] [RIGHT] Move the cursor left and right
[ENT] Start the selected cursor item
[RET] Return to top menu
Screen 9: *OP Check Menu
Purpose: Verify OP related such as delta IOP and LD time
[UP] [DOWN] Move the cursor up and down
[ENT] Start the selected cursor item
[RET] Return to top menu
Screen 10: *Load Eject Aging Not Use
Purpose: Perform load eject aging
[UP] [DOWN] Move the cursor up and down
[LEFT] [RIGHT] Move the cursor left and right
[ENT] Start the selected cursor item
[RET] Return to top menu
Screen 11: *Spindle Control Check Menu Not Use
Purpose: Verify spindle rotation
[UP] [DOWN] Move the cursor up and down
[LEFT] [RIGHT] Move the cursor left and right
[ENT] Start the selected cursor item
[RET] Return to top menu
Screen 12: *FA Mode Test Not Use
Purpose: Perform FA(Drive) aging
[UP] [DOWN] Move the cursor up and down
[ENT] Start the selected cursor item
[RET] Return to top menu
New service method
1. All of BU data on the barcode label is shot by digital camera in order to make a JPEG file of BU data.
2. Application software in the PC makes digital data from JPEG file.
3. The converted data is stored to USB memory.
4. The USB memory is connected to BDP 5G unit.
5. In service mode, there is a command to save the data from USB memory to board memory.