JVC LT-37DS6FJ
SERVICE MODE CHECKABLE AND POWER SUPPLY CIRCUIT
SYSTEM
Be sure to carry out
the following operation at the end of the procedure.
(1) Press the [INFORMATION]
key and [MUTING] key simultaneously, then enter the SERVICE MODE.
(2) When the Main Menu is displayed, press [2] key to enter the self check mode.
(3) Turn off the power by pressing the [POWER] key on the remote control unit.
(2) When the Main Menu is displayed, press [2] key to enter the self check mode.
(3) Turn off the power by pressing the [POWER] key on the remote control unit.
SERVICE MODE SETTING
ADJUSTMENT
PREPARATION
(1) The adjustment using the REMOTE CONTROL UNIT is made on the basis of the initial setting values. The setting values which adjust the screen to the optimum condition can be different from the initial setting values.
(2) Make sure that connection is correctly made AC to AC power source.
(3) Turn on the power of the TV and measuring instruments for warming up for at least 30 minutes before starting adjustments.
(4) If the receive or input signal is not specified, use the most appropriate signal for adjustment.
(5) Never touch the parts (such as variable resistors, transformers and condensers) not shown in the adjustment items of this service adjustment.
(1) The adjustment using the REMOTE CONTROL UNIT is made on the basis of the initial setting values. The setting values which adjust the screen to the optimum condition can be different from the initial setting values.
(2) Make sure that connection is correctly made AC to AC power source.
(3) Turn on the power of the TV and measuring instruments for warming up for at least 30 minutes before starting adjustments.
(4) If the receive or input signal is not specified, use the most appropriate signal for adjustment.
(5) Never touch the parts (such as variable resistors, transformers and condensers) not shown in the adjustment items of this service adjustment.
HOW TO ENTER THE SERVICE MODE
(1) Press [INFORMATION] key and [MUTING] key on the remote control unit simultaneously to enter the SERVICE MODE SCREEN.
(2) In the SERVICE MENU, press the [1] key to display ADJUSTMENT MODE SCREEN.
(1) Press [INFORMATION] key and [MUTING] key on the remote control unit simultaneously to enter the SERVICE MODE SCREEN.
(2) In the SERVICE MENU, press the [1] key to display ADJUSTMENT MODE SCREEN.
NOTE:
# Before entering the SERVICE MODE, confirm that the setting of VCR/TV/DVD switch is at the "TV" side. If the switches have not been properly set, you cannot enter the SERVICE MODE.
# When a number key other than the [1] key is pressed in the SERVICE MODE SCREEN, the other relevant screen may be displayed. This is not used in the adjustment procedure. Press the [MENU] key to return to the SERVICE MODE SCREEN.
# Before entering the SERVICE MODE, confirm that the setting of VCR/TV/DVD switch is at the "TV" side. If the switches have not been properly set, you cannot enter the SERVICE MODE.
# When a number key other than the [1] key is pressed in the SERVICE MODE SCREEN, the other relevant screen may be displayed. This is not used in the adjustment procedure. Press the [MENU] key to return to the SERVICE MODE SCREEN.
HOW TO EXIT THE SERVICE MODE
Press the [MENU] key to exit the Service mode.
Press the [MENU] key to exit the Service mode.
WHITE BALANCE
(1) Receive a PAL 75%
all white signal.
(2) Set PICTURE MODE to "STANDARD".
(3) Set ZOOM to "FULL".
(4) Set COLOUR TEMP. to "NORMAL".
(5) Select "1.ADJUST" from the SERVICE MODE.
(6) Adjust to Keep one of < S030 > (Red drive), < S031 > (Green drive) or < S032 > (Blue drive) unchanged, then lower the other two so that the all-white screen is equally white throughout.
NOTE:
Set one or more of < S030 >, < S031 >, and < S032 > to "85".
(7) Check that white balance is properly tracked from low light to high light. If the white balance tracking is deviated, adjust to correct it.
(8) Press the [MUTING] key to memoirze the set value.
(2) Set PICTURE MODE to "STANDARD".
(3) Set ZOOM to "FULL".
(4) Set COLOUR TEMP. to "NORMAL".
(5) Select "1.ADJUST" from the SERVICE MODE.
(6) Adjust to Keep one of < S030 > (Red drive), < S031 > (Green drive) or < S032 > (Blue drive) unchanged, then lower the other two so that the all-white screen is equally white throughout.
NOTE:
Set one or more of < S030 >, < S031 >, and < S032 > to "85".
(7) Check that white balance is properly tracked from low light to high light. If the white balance tracking is deviated, adjust to correct it.
(8) Press the [MUTING] key to memoirze the set value.
SELF CHECK MODE
Before entering the SERVICE MODE, confirm that the setting of VCR/TV/ DVD switch is at the "TV" side. If the switches have not been properly set, you cannot enter the SERVICE MODE.
(1) Press the [INFORMATION] key and [MUTING] key simultaneously, then enter the SERVICE MODE.
(2) Press the [2] key SELF CHECK MODE.
(3) Press the [RED] key to enter Page 2 of the SELF CHECK MODE.
#Use the [GREEN] key to toggle between 1 and 2.
Before entering the SERVICE MODE, confirm that the setting of VCR/TV/ DVD switch is at the "TV" side. If the switches have not been properly set, you cannot enter the SERVICE MODE.
(1) Press the [INFORMATION] key and [MUTING] key simultaneously, then enter the SERVICE MODE.
(2) Press the [2] key SELF CHECK MODE.
(3) Press the [RED] key to enter Page 2 of the SELF CHECK MODE.
#Use the [GREEN] key to toggle between 1 and 2.
When a number key
other than the [2] key is pressed in the SERVICE MODE screen, the other
relevant screen may be displayed. This is not used in the SELF CHECK MODE.
Press the [MENU] key to return to the MAIN MENU SCREEN.
EXIT THE SELF CHECK MODE
Turn off the power by unplugging the AC power cord plug whe in the Self check display mode.
To Clear (Reset) Failure History:
Turn off the power by pressing the [POWER] key on the remote control unit when in the Self check display mode
Turn off the power by unplugging the AC power cord plug whe in the Self check display mode.
To Clear (Reset) Failure History:
Turn off the power by pressing the [POWER] key on the remote control unit when in the Self check display mode
ITEMS UNDER SELF CHECK
|
Detection item
|
Display
|
Detection content
|
|
Low bias line short
protection |
LOB
|
Confirmation of operation of the low bais (2.5V / 3.3V / 5V / 9V) protection circuit. Q9801 , Q9822 [REGULATOR PWB]
|
|
Abnormal rise of
temperature in audio circuit |
FAN
|
Confirmation of the temperature of
audio circuit. TH6661 [ANALOG SIGNAL PWB] |
|
Presence of sync signal
|
SYNC
|
Confirmation of presence of video
sync signal. M : Main sync signal S : Sub sync signal HD : Component sync signal IC201 [ANALOG SIGNAL PWB] |
|
AC power input
|
TIM
|
Not used.
|
|
Main CPU
communication |
MSM
|
Not used.
|
|
Digital tuner
|
DIGI
|
Not used.
|
|
Main memory
|
MEM
|
Confirmation of reply of ACK signal
which uses I2C communication. IC7602 [DIGITAL SIGNAL PWB] |
|
AV select switch
|
AVSW
|
Same as above.
IC301, IC501 [ANALOG SIGNAL PWB] |
|
3 dimensions YC
separator |
YC
|
Not used.
|
|
Multi sound process
|
AIO
|
Not used.
|
|
RF tuner
|
TUN
|
Confirmation of reply of ACK signal
which uses I2C communication. TU3002 [RECEIVER PWB] |
|
Ghost reduction
|
GCR
|
Not used.
|
|
DIST process
|
IP
|
Confirmation of reply of ACK signal
which uses I2C communication. IC3001 [DIGITAL SIGNAL PWB] |
|
RGB process
|
RGB
|
Confirmation of reply of ACK signal
which uses I2C communication. IC3001 [DIGITAL SIGNAL PWB] |
|
DVI (Digital communication)
|
DVI
|
Not used.
|
|
Digital input |
HDMI
|
Confirmation of reply of ACK signal
which uses I2C communication. |
POWER SUPPLY CIRCUIT
CLICK ON THE IMAGE TO ZOOM IN
