SONY KDL-32S3000 - KDL-40S3000 - KDL-46S3000
LCD TV
SERVICE MODE LED BLINKING CODE AND DESCRIPTION
SELF DIAGNOSIS
The identification of errors within the SE1A
chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to
respond to IIC. In the event of one of these situations arising the software
will first try to release the bus if busy (Failure to do so will report with a
continuous flashing LED) and then communicate with each device in turn to
establish if a device is faulty. If a device is found to be faulty the relevant device number will be displayed through the LED (Series of flashes which must
be counted).
LED BLINKING CODES AND CAUSES
Number
of LED
Flashes |
Error
Description
|
02
|
Balancer
error.
|
03
|
Power
supply protection error.
|
04
|
Panel
error.
|
05
|
NVM
error.
|
06
|
IIC
error.
|
07
|
HDMI
error.
|
08
|
Digital
error.
|
09
|
Tuner
Error
|
10
|
Sound
processor
|
11
|
WCG
port error
|
12
|
WCG IC
error
|
13
|
RTC error
|
14
|
FRCH
error (Only models with FRCH)
|
LED BLINKING ERROR DESCRIPTION
Error
Description
|
Meaning/Related
Fault
|
Balancer
error.
|
Balancer
error/PANEL_DET (PMUX6.7) to low level, between 2.48V and 0.83V.
|
Power
supply protection error.
|
5V,
3.3V or 1.8V failure/POWER_DET (P1_0) to high level.
|
Panel
error.
|
Inverter
failure/PANEL_DET (PMUX6.7) to low level, less than 0.83V.
|
NVM
error.
|
EEPROM
cannot be read or written.
|
IIC
error.
|
IIC bus
cannot be correctly initialised.
|
HDMI
error.
|
HDCP
cannot be set-up correctly.
|
Digital
error.
|
Digital
CPU does not respond by DPI communication (Only for digital models).
|
Tuner
Error
|
IF
circuit or PLL circuit does not respond to IIC commands.
|
Sound
processor
|
MSP3410G
IC does not respond to IIC commands.
|
WCG
port error
|
FPGA
has not been configured properly by HW.
|
WCG IC
error
|
FPGA
Wide Colour Gamut device does not respond to IIC commands.
|
RTC error
|
RTC IC
does not respond to IIC commands (Only for digital models).
|
FRCH
error
|
Only in
FRCH models, when communication through IIC fails.
|
REAR COVER REMOVAL
How to enter into the Service Mode
1. Turn on the main power switch.
2. Press the following sequence of buttons on the Remote Commander.
2. Press the following sequence of buttons on the Remote Commander.
ON SCREEN
DISPLAY > DIGIT 5> VOLUME + > SCREEN FORMAT > SCREEN FORMAT
TT—’ will appear in the upper right corner of
the screen. Other status information will also be displayed
3. Press ‘MENU’ on the remote commander to
obtain the following on the screen
BACKLIGHT
HDMI
SOUND
IF ADJUST
ERROR MENU
SE1A v0.13a Jan07
FACTORY DATA: 11111111
SERIAL NUMBER: 4294967295
WORKING TIME: 0:22
HDMI
SOUND
IF ADJUST
ERROR MENU
SE1A v0.13a Jan07
FACTORY DATA: 11111111
SERIAL NUMBER: 4294967295
WORKING TIME: 0:22
4. Move to the corresponding adjustment item
using the up or down arrow buttons on the Remote Commander.
5. Press the right arrow button to enter into the required menu item.
6. Press the ‘Menu’ button on the Remote Commander to quit the Service Mode when all adjustments have been completed.
5. Press the right arrow button to enter into the required menu item.
6. Press the ‘Menu’ button on the Remote Commander to quit the Service Mode when all adjustments have been completed.
Note :
# After carrying out the service adjustments, to prevent the customer accessing the ‘Service Menu’ switch the TV set OFF and then ON.
# After carrying out the service adjustments, to prevent the customer accessing the ‘Service Menu’ switch the TV set OFF and then ON.
SONY TV SERVICE TIPS
SONY KV32XBR45
CONVERGENCE PROBLEM
TV has convergence of all vertical lines
are displace horizontally
SOLUTION
Suggest tech look for R789 and see if it is open It is on the on "C" board. It The value is around 10 meg. There are two different chassis and CRTs used for this model. If they have the older chassis type that requires H stat convergence (CRT board has H stat control) they need to order the older CRT as per the manual. If newer type (No H stat) then the new CRT as per Service Manual supplement -1 is needed. CRT 8-733-743-05 The H Stat is done using the Yoke ring magnets. I have attached the two Service Manual supplements, and the SB325R1
Suggest tech look for R789 and see if it is open It is on the on "C" board. It The value is around 10 meg. There are two different chassis and CRTs used for this model. If they have the older chassis type that requires H stat convergence (CRT board has H stat control) they need to order the older CRT as per the manual. If newer type (No H stat) then the new CRT as per Service Manual supplement -1 is needed. CRT 8-733-743-05 The H Stat is done using the Yoke ring magnets. I have attached the two Service Manual supplements, and the SB325R1
