SONY KDL-40VL130 - KDL-52W3000 - KDL-52WL130 - KDL-52WL135
SERVICE MODE LED BLINKING CODE AND POWER SUPPLY CIRCUIT
HOW TO
ACTIVATE THE SELF DIAGNOSTIC FEATURE
1. TV must be in standby mode. (Power off).
2. Press the following buttons on the Remote Commander within a second of each other:
DISPLAY BUTTON > Channel 5 > Volume - > TV POWER .
2. Press the following buttons on the Remote Commander within a second of each other:
DISPLAY BUTTON > Channel 5 > Volume - > TV POWER .
LED BLINKING CODES
|
LED BLINKING
|
DIGNOSING
|
|
002
|
PVO_WOP
|
|
003
|
1RRE_WOP
|
|
005
|
NOC_T
|
|
006
|
ETILKCAB
|
|
007
|
PMETLNAP
|
|
008
|
TORP_DUA
|
|
009
|
RRE_NAF
|
|
010
|
RRE_TTD
|
|
013
|
RECNALAB
|
|
101
|
TDW_TTD
|
|
102
|
TDW_MVT
|
|
103
|
TDW_MEB
|
INVERTER BOARD REMOVAL
Only remove the screws securing the inverter cover which may be metal or plastic. The remaining plastic strip contains sockets for the fluorescent backlights and should never be loosened. The backlights will pop out of the sockets and/or break the backlight requiring a LCD panel replacement. The example shown is a 32” model but applies to all models.
Only remove the screws securing the inverter cover which may be metal or plastic. The remaining plastic strip contains sockets for the fluorescent backlights and should never be loosened. The backlights will pop out of the sockets and/or break the backlight requiring a LCD panel replacement. The example shown is a 32” model but applies to all models.
NOTE: For the 52” models, the connector that
attaches the Left Upper (Balancer) Inverter board to the DF5 board has a strip
of white tape at both ends of the connector. The connector that attaches the Right
Upper (Balancer) Inverter board to the DF4 board has a strip of red tape at
both ends of the connector.
NEVER REMOVE THE SCREWS SECURING THE PLASTIC
STRIP HOLDING THE LAMP SOCKETS
DAMAGE TO THE BACKLIGHT TUBES WILL OCCUR
ACCESSING SERVICE ADJUSTMENTS
To adjust various set features, use the Remote Commander to put the set into service mode to display the service menus.
1. TV must be in standby mode. (Power off).
2. Press the following buttons on the Remote Commander within a second of each other:
DISPLAY > Channel 5 > Volume + > TV POWER .
To adjust various set features, use the Remote Commander to put the set into service mode to display the service menus.
1. TV must be in standby mode. (Power off).
2. Press the following buttons on the Remote Commander within a second of each other:
DISPLAY > Channel 5 > Volume + > TV POWER .
The first service menu (TV) displays.
3. To display the service menu that contains the category you want to adjust, press JUMP on the Remote Commander.
3. To display the service menu that contains the category you want to adjust, press JUMP on the Remote Commander.
The screen displays the first category in the
selected service menu.
4. To change the category, press 2 or 5 on the Remote Commander.
Note: Pressing 2 or 5 only changes the categories within the service menu displayed. To change a category on one of the other service menus, press the JUMP button until the correct service menu is displayed.
5. To change the adjustment item, press 1 or 4 on the Remote Commander.
6. To change the data value, press 3 or 6 on the Remote Commander.
7. To write into memory, press MUTING then 0 on the Remote Commander.
8. To exit service mode, turn the power off.
4. To change the category, press 2 or 5 on the Remote Commander.
Note: Pressing 2 or 5 only changes the categories within the service menu displayed. To change a category on one of the other service menus, press the JUMP button until the correct service menu is displayed.
5. To change the adjustment item, press 1 or 4 on the Remote Commander.
6. To change the data value, press 3 or 6 on the Remote Commander.
7. To write into memory, press MUTING then 0 on the Remote Commander.
8. To exit service mode, turn the power off.
AFTER REPLACING THE FB1 BOARD OR FB3 BOARD UPDATING
MODEL INFORMATION
Complete the following steps to reset the model information to the
correct size after replacing the FB1 Board or FB3 Board.
1. Access the Service Menu by pressing the following buttons on the
Remote Commander within a second:
DISPLAY Channel 5 Volume + TV POWER .
The service menu displays.
2. Press the JUMP button until the BEM micro service menu displays
Complete the following steps to reset the model information to the
correct size after replacing the FB1 Board or FB3 Board.
1. Access the Service Menu by pressing the following buttons on the
Remote Commander within a second:
DISPLAY Channel 5 Volume + TV POWER .
The service menu displays.
2. Press the JUMP button until the BEM micro service menu displays
3. Press 2 until the 0001 MODEL_INFO category
displays.
4. Do one of the following:
FOR 40 INCH SET 0
FOR 52 INCH SET 1
5. To write to memory, press MUTING then 0 on
the Remote Commander.
8. To exit service mode, turn the power off
8. To exit service mode, turn the power off
POWER SUPPLY CIRCUIT
40 INCH
52 INCH
CLICK ON THE IMAGE TO ZOOM IN
