Sunday, November 29, 2015

UNIVERSAL REMOTE FOR BLU RAY AND MEDIA PLAYERS ONN ONB13AV004 CODES AND PROGRAMMING

UNIVERSAL REMOTE FOR BLU RAY AND MEDIA PLAYERS  

ONN ONB13AV004

CODES AND PROGRAMMING 

ENTERING CODE DIRECTLY
1. Locate the Remote Code List provided in this manual. Find the DEVICE CATEGORY you wish to program (for example TV, DVD, SAT, AUX) and then find the BRAND of that device. Circle all the codes under that brand. Example: For a GE TV, locate the TV code section then circle all of the GE TV codes.
2. Manually turn on the device you wish to control.
3. Press and hold the SETUP button until the red indicator light stays on (approximately 2 seconds) and then release the SETUP button.
4. Press and release the desired device button on the remote (TV, DVD, SAT, AUX). The red indicator will blink once and then remain on.
5. Enter the first 4-digit code previously found in the code list using the number buttons on the remote. If the code entered is a valid code, the red indicator light will turn off. If the code entered is not a valid code, the red indicator light will flash and remain on allowing you to re-enter the code.
Note: If no buttons are pressed for 35 seconds, the remote will exit the SETUP mode and you will have to start over.
6. Point the remote at the device. Press the POWER button—if the device turns off, no further programming is required for that device. If the device does not turn off, return to step 3 and use the next code found in the code list. Continue this process until a code for your device is found.
Notes
# If your device does not respond to the remote after trying all codes listed or your brand is not listed in the code list, use the Auto Code Search method to program your remote.
#Sometimes the first code that “works” with your device may operate only a few functions of your device. There may be another code in the code list that performs more functions. Try other codes from the code list for more functionality.
# You can use any device button to control other devices in your home entertainment system. For example, you can use the AUX device button to control an audio receiver or a DVD, VCR, satellite, etc.
# For combination devices, you may have to enter a code for each device. For example, for a VCR/DVD device, you may have to enter a code for the DVD under the DVD button and enter a code for the VCR using a different device button on the remote.
# Write down the code found to operate your device for future reference.
SEARCHING FOR THE CODE
The Auto Code Search searches automatically through all of the codes stored in this remote. Read all the following steps prior to starting the auto search as you will need to be prepared to lock-in the proper code when found.
1. Manually turn on the device you wish to control.
2. Press and hold the SETUP button until the red indicator light stays on (approximately 4 seconds) and then release the button.
3. Press and release the desired device button on the remote (TV, DVD, SAT, AUX). The red indicator will blink once and then remain on.
4. Point the remote at the device and press and release the POWER button (for TV) or PLAY button (for DVD, VCR, etc.) to start the search. The red indicator will flash (approximately every 2 seconds) as the remote searches. Note: The remote must be pointed at the device for the duration of this search.
5. Place your finger on the #1 button so you are prepared to lock-in the code.
6. When the device shuts off or begins playing, press the #1 button to lock-in the code. The red indicator light will turn off. Note: You have approximately two seconds after the device shuts off or begins playing to lock-in the code.
7. Point the remote at the device and check to see if the remote operates the device as desired. If it does, no further programming is required for that device. If it does not, return to step 2 and start the auto search.
Notes
# This process may take several minutes as the remote contains many codes.
# The SETUP button can be used during the search process to reverse the direction of the search of the remote codes. For example, if you miss the code for your device and the remote is continuing to search (as indicated by the blinking red light), press the SETUP button and the code search will reverse direction and return to the code.
# When using the Auto Code Search programming method, the device button corresponding to the type of device you want to control must be selected (for example, the TV device button must be selected in step 3 if you want to control a TV, the DVD/VCR device button for a DVD player, etc.)
# Sometimes the first code that “works” with your device may operate only a few functions of your device. There may be another code in the code list that performs more functions. Continue the code search as directed above until the best code is found.
CODES FOR STREAMING MEDIA
Apple 5541, 4295
Asus 1684
Dlink 1614, 1724
HP 1624
Iomega 1744
LG 1714
Magnavox 1704
Netgear 1604, 4475
Niveus 1634
Philips 1654
Popcorn Hour 1664
RCA 1694
Roku 4395, 4355
Seagate 1674
Sling Media 1644
Vudu1 734
WD 4345, 4265
X-Box 4245, 4255
CODES FOR BLU RAY PLAYER 
Denon 4035
Dynex 4235
HP4085
Insignia4205, 0975, 2635
JVC 2385
LG 4285, 2635, 2335
Magnavox 2425
Memorex 2375
Onkyo 2355
Oppo 4365, 4375, 4385, 4045
Panasonic 4175, 2395
Philips 2415
Pioneer 4055
Samsung 4125, 2325, 2345, 4095
Sharp 4115, 2315
Sherwood 4225, 4065
Sony 4165, 4275, 2305
Sylvania 4215, 2405
TCL 2435
Toshiba 2295
Vizio 4135, 4025
Yamaha 4075