Contents of this article
- Led blinking codes
- Service mode
- White balance Adjustments
PANASONIC TX-32LX600P - TX-26LX600F
SERVICE MODE AND ADJUSTMENTS
How to remove the back cover
Remove the cable cover.
Remove the 15 fixing screws.
Remove the cable cover.
Remove the 15 fixing screws.
Self Check
Self-check is used to automatically check the bus lines and hexadecimal code of
the TV set. To enter Self-Check mode, keep pressing the STATUS button on the
remote control and press the down (-/v) button on the TV set. To exit Self
Check, switch off the TV set at the power button.
If the CCU ports have been
checked and found to be incorrect or not located then " - - " will
appear in place of "O.K
Power LED blinking
When abnormality has occurred the unit, the protection circuit operates and
reset to the stand by mode. At this time, the defective block can be identified by number of blinking of the Power LED on the
front panel of the unit.
LED BLINKING CODE AND CAUSES
Blinking times
|
Contents
|
Check point
|
1
|
Inverter SOS
|
POWER UNIT
LCD PANEL |
3
|
BT_30V, SOUND 18V,
PANEL 12V
|
AP BOARD, H BOARD
|
4
|
SUB 9V
|
AP BOARD, H BOARD
DG BOARD |
5
|
SUB 5V
|
AP BOARD, H BOARD
DG BOARD |
6
|
MAIN 9V
|
AP BOARD, DG BOARD
|
8
|
MAIN 3,3V
|
AP BOARD, H BOARD
DG BOARD |
Service Mode Function
MPU controls the functions switching for each IICs through IIC bus in this chassis. The following setting and adjustment can be adjusted by remote control in Service Menu
How to enter SERVICE 1
In main menu, move to choose sound menu, set BASS to MAXIMUM, and set TREBLE to MINIMUM. Simultaneously press INDEX button on remote control and DOWN button (-/v) on the TV set.
How to enter SERVICE 2
Enter the SERVICE 1 mode.
Press the GREEN button to step down to the last menu position.
Set the program position to 99.
Press HOLD button on remote control.
Note:
To exit from Service mode, press N or Power button on remote control
MPU controls the functions switching for each IICs through IIC bus in this chassis. The following setting and adjustment can be adjusted by remote control in Service Menu
How to enter SERVICE 1
In main menu, move to choose sound menu, set BASS to MAXIMUM, and set TREBLE to MINIMUM. Simultaneously press INDEX button on remote control and DOWN button (-/v) on the TV set.
How to enter SERVICE 2
Enter the SERVICE 1 mode.
Press the GREEN button to step down to the last menu position.
Set the program position to 99.
Press HOLD button on remote control.
Note:
To exit from Service mode, press N or Power button on remote control
Key Command
# Press the RED/GREEN button to step up/down through the functions and adjustments.
# Press the YELLOW/BLUE button to change the adjustment values or function.
# Press the numerical button 1-7 to change 0/1 of each option item.
# Press the OK button after each adjustment has been made to store the required values.
# Press the RED/GREEN button to step up/down through the functions and adjustments.
# Press the YELLOW/BLUE button to change the adjustment values or function.
# Press the numerical button 1-7 to change 0/1 of each option item.
# Press the OK button after each adjustment has been made to store the required values.
Subcontrast adjustment
1. Receive PAL colour bar (100% white) RF signal.
2. Enter “Sub-Contrast” adj. In SERVICE 1 mode.
3. Start adjusting by using Blue Key.
4. If the adjustment finished normally, the letter of “Sub-Contrast” will change from red to black
White Balance adjustment
1. Procedure basically perform checking using the production software and make automatic adjustment using external computer.
2. It adjust in the mode of Colour balance Normal as follows.
TX-32LX600F, TX-32LX600P TX-26LX600F, TX-26LX600P
TOP Normal TOP Normal
x: 0,2800 ± 0,003 x: 0,2800 ± 0,003
y: 0,2850 ± 0,003 y: 0,2850 ± 0,003
GRAY Normal GRAY Normal
x: 0,2800 ± 0,003 x: 0,2800 ± 0,003
y: 0,2850 ± 0,003 y: 0,2850 ± 0,003
The address of EEPROM to write is as follows
Add. C148-C159
1. Receive PAL colour bar (100% white) RF signal.
2. Enter “Sub-Contrast” adj. In SERVICE 1 mode.
3. Start adjusting by using Blue Key.
4. If the adjustment finished normally, the letter of “Sub-Contrast” will change from red to black
White Balance adjustment
1. Procedure basically perform checking using the production software and make automatic adjustment using external computer.
2. It adjust in the mode of Colour balance Normal as follows.
TX-32LX600F, TX-32LX600P TX-26LX600F, TX-26LX600P
TOP Normal TOP Normal
x: 0,2800 ± 0,003 x: 0,2800 ± 0,003
y: 0,2850 ± 0,003 y: 0,2850 ± 0,003
GRAY Normal GRAY Normal
x: 0,2800 ± 0,003 x: 0,2800 ± 0,003
y: 0,2850 ± 0,003 y: 0,2850 ± 0,003
The address of EEPROM to write is as follows
Add. C148-C159
INNER LAYOUT
1. EAB833AL SPEAKER BOX L
2. EAB833AR SPEAKER BOX R
3. EAK7E14A2 SQUAWKER SP
4. ENG37A12GF TUNER
5. ETXMM614EAA POWER UNIT
6. K2CQ2DZ00007 AC CORD
7. N2QAYB000048 REMOTE CONTROL
8. RD-SD0010P SD MODULE
9. TBMA163 PANASONIC BADGE
10. TBXA46502 POWER BUTTON
11. TEKC029 DAMPER
12. TEKX020 SD DOOR
13. TKKC5214 SD PANEL
14. TKKL5290 CONNECTOR COVER
15. TKP0E12901 REAR AV BRACKET
16. TKPA94502 DOOR
17. TKRA46401 SD ORNAMENT
18. TKXA18501 CABLE COVER
19. TKZX5183 REAR SUPPORT MTG SU
20. TKZX5190 REAR SUPPORT MTG L
21. TKZX5191 REAR SUPPORT MTG R
22. TMW0E105 FRONT BRACKET
23. TMWA044-1 K PRINT BRACKET
24. TMWX032 SD BRACKET
25. TNPA3864AA G P.C.B.
26. TNPA3865AB V P.C.B.
27. TNPA3866AA K P.C.B.
28. TNPA3867AA GS P.C.B.
29. TNPA3868AB AP P.C.B.
30. TNPH0657AB H P.C.B.
31. TUA0E0500 MAIN CHASSIS FRAME
32. TUXE259 GS FIX METAL
33. TXFBL010Q49 PEDESTAL ASSY
2. EAB833AR SPEAKER BOX R
3. EAK7E14A2 SQUAWKER SP
4. ENG37A12GF TUNER
5. ETXMM614EAA POWER UNIT
6. K2CQ2DZ00007 AC CORD
7. N2QAYB000048 REMOTE CONTROL
8. RD-SD0010P SD MODULE
9. TBMA163 PANASONIC BADGE
10. TBXA46502 POWER BUTTON
11. TEKC029 DAMPER
12. TEKX020 SD DOOR
13. TKKC5214 SD PANEL
14. TKKL5290 CONNECTOR COVER
15. TKP0E12901 REAR AV BRACKET
16. TKPA94502 DOOR
17. TKRA46401 SD ORNAMENT
18. TKXA18501 CABLE COVER
19. TKZX5183 REAR SUPPORT MTG SU
20. TKZX5190 REAR SUPPORT MTG L
21. TKZX5191 REAR SUPPORT MTG R
22. TMW0E105 FRONT BRACKET
23. TMWA044-1 K PRINT BRACKET
24. TMWX032 SD BRACKET
25. TNPA3864AA G P.C.B.
26. TNPA3865AB V P.C.B.
27. TNPA3866AA K P.C.B.
28. TNPA3867AA GS P.C.B.
29. TNPA3868AB AP P.C.B.
30. TNPH0657AB H P.C.B.
31. TUA0E0500 MAIN CHASSIS FRAME
32. TUXE259 GS FIX METAL
33. TXFBL010Q49 PEDESTAL ASSY
