Tuesday, January 12, 2016

DENON DBP – 1610 Service mode – Initialization - Network firmware update – factory reset – Try lock – remote lock – Blu ray player repair and service

                                                Category: Blu Ray player Repair and Service 

                                                Content of this article 

  • Initialization of the Player 
  • How to access to Service mode 
  • Firmware update  

DENON DBP-1610

HOW TO INITIALIZE THE BLU-RAY DISC PLAYER
To put the program back at the factory-default, initialize the BD player as the following procedure.
1. Turn the power on.
2. Remove the disc on the tray and close the tray.
3. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order.
4. Press [ STOP ] button on the remote control unit. CLEAR appears on the VFD.
5. To exit this mode, press [POWER OFF] button.
FIRMWARE RENEWAL MODE
Note: The file extension of the available firmware is “b20”.
1. Turn the power on and remove the disc on the tray and close the tray.
2. To put the BD player into version up mode, press [9], [8], [7], [6], and [POP UP MENU/MENU] buttons on the remote control unit in that order.
The tray will open automatically.
3. Load the disc for version up.
4. The BD player enters the F/W version up mode automatically. Make sure to insert the proper F/W for the state of this model.
5. After programming is finished, the checksum on the VFD.
Checksum appears on the VFD then the tray will open automatically. Remove the disc on the tray. At this time, no button is available.
6. Unplug the AC cord from the AC outlet. Then plug it again.
7. Turn the power on.
8. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order.
9. Press [ STOP ] button on the remote control unit.
To exit this mode, press [POWER OFF] button.
Network Firmware Update
1. Press [SETUP] button on the remote control unit in stop mode.
2. Use [LEFT/ RIGHT] button to select “CUSTOM”, then press [ENTER] button.
3. Use [LEFT/ RIGHT] button to select “Other”, then press [ENTER] button.
4. Use [UP / DOWN] button to select “Network Update”, then press [ENTER] button. Confirmation message will appear.
5. Use [UP/ DOWN] button to select “Yes”, then press [ENTER] button.
This unit will start checking for the latest firmware version.
NOTE:
If any error message concerning the network environment appears, please confirm the setting of your unit according to the error message. If you need to change any of your network environmental setting in order to execute the update, please contact to the internet service provider.
6. Confirmation message will appear.
Use [UP/ DOWN] button to select “Yes”, then press [ENTER] button.
The unit will start downloading the latest firmware version.
7. When the download completes, confirmation message will appear.
Press [ENTER] button.
The unit will start updating the firmware version. It may take a while to complete the updating.
(Please wait until “100%” appears on the front panel display.)
8. After updating finishes, this unit will restart and open the disc tray automatically.
How to Verify the Firmware Version
1. Turn the power on.
2. Remove the disc on the tray and close the tray.
3. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order.
4. To exit this mode, press [POWER OFF] button.
SERVICE MODE
Entering Service Mode
In power on condition, no discs and tray close, it will be entered into service mode by the following operation using the remote controller. However, it will not be entered when Media Select Item is SD Memory.
Service Mode by using remote controller
Press the following buttons on the remote controller in power on condition, no discs and tray close; [2]>[5]>[8]>[0]>[CLEAR]
Release from Service Mode
Press the [POWER OFF] button to turn off power.
Screen saver/Auto Power Off in Service Mode
These functions are not performed in Service Mode.
TRAY LOCK MODE
Tray Lock Mode prevents the tray opening or closing to prevent disc theft in demo mode.
Enter this mode using the following procedure.
1. Confirm that the TV Monitor is connected.
2. With playback stopped, press [SETUP], [TOP MENU], [3], [AUDIO], [0] and [SETUP] buttons on the remote control unit in that order. "Trade-On" appears in the upper right corner on the screen.
3. To exit this mode, press [SETUP], [TOP MENU], [3], [AUDIO], [0] and [SETUP] buttons on the remote control unit in that order. "Trade-Off" appears in the upper right corner on the screen,
REMOTE LOCK MODE
SETTING MENU
Remote Lock Off Mode:
This mode receives an input signal from the remote control unit or from the Remote In-Jack on the rear panel.
Remote Lock On Mode:
This mode dose not receive an input signal from the remote control unit or from the Remote In-Jack on the rear panel.
Perform the setting using the following procedure.
1. Press [POWER ON] and [STOP] buttons on the front panel simultaneously for over 3 seconds to set "Remote Lock Mode" and display mode.
2. Press [STILL/PAUSE] button on the front panel to set to "On" or "Off". When "Remote Lock On", "Remote Lock On" will appear in the upper right corner on the screen.
When "Remote Lock Off", "Remote Lock Off" will appear in the upper right corner on the screen.
a. If [STILL/PAUSE] button is not pressed for 2 seconds or any other button is pressed within 2 seconds, the unit will be released from "Remote Lock Mode".
b. When initializing, set the Remote Lock Mode "off".