Friday, January 01, 2016

SHARP LC-32LE700 - LC-40LE700 - LC-46LE700 - 52LE700 Service mode and firmware update procedure

Contents of this article 

  • Services mode
  • Firmware update 
  • HDMI pin configuration 



SHARP LC-32LE700 - LC-40LE700 - LC-46LE700 - 52LE700

Firmware Upgrade Procedure
1. Turn off the AC power (Unplug the AC power cord).
2. Insert the upgrading USB flash memory for upgrade into the service slot.
3. While holding down the power button, plug in the AC power cord of the main unit to turn on the power.
4. Upgrade begins automatically. After the set starts, the upgrade screen will displayed.
5. If any of the procedures fails, the upgrade failure screen shows up. For the failing procedure, the “NG” marking turns red.
NOTE: In such case, try to upgrade the software again. If it still fails, the hardware may be in trouble.
6. When all the procedures are complete, the following upgrade success screen shows up. The new software version can be confirmed on screen. The version number appears when each item has been successfully upgraded. Finally the main version number appears on screen.
7. Turn off the AC power (Unplug the AC power cord). Take out the upgrading USB flash memory.
It waits for about 20 seconds until the AC power supply is turned off.
8. Now the software has been upgraded.
NOTE: Then get the set started and call the process adjustment screen 1/17 to check the main software version.
CAUTION:
1) Do not take out and put in the USB flash memory during formatting.
2) It takes about one minute to the rewriting completion.
Please confirm the upgrade status on the screen becomes 100%.
3) The AC power supply of the set is waited for about 20 seconds until off (The
AC outlet is pulled out) after the upgrade is completed
Entering and exiting the adjustment process mode
1. Unplug the AC power cord of running TV set to force off the power.
2. While holding down the “VOL (-)” and “INPUT” keys on the set at once, plug in the AC power cord to turn on the power.
The letter “K” appears on the screen.

3. Next, hold down the “VOL (-)” and “P (DOWN)” keys on the set at once. Multiple lines of blue characters appearing on the screen indicate that the set is now in the adjustment Process mode. If you fail to enter the adjustment process mode (the display is the same as normal startup), retry the procedure.
4. To exit the adjustment process mode after the adjustment is done, unplug the AC power cord to force off the power. (When the power is turned off with the remote controller, once unplug the AC power cord and plug it in again. In this case, wait 10 seconds or so before plugging.)
LED Flashing
LED flashing specification at the time of the error
Display method
Make the OPC LED flash using the [MENU] key on the remote control since the display for service persons is identified by the number of flashings (once to 5 times). Even if the [MENU] key is pressed again, it does not return to the display for customers (only the power LED flashes).
After recovering from an error, if the same error cannot be generated again, refer to MONITOR ERR CAUSE on the adjustment process screen. shing method
Synchronize the phases of the power LED and OPC LED.
If the LEDs have different number of flashings, adjust the flashing cycle to that where the LED flashes more times
Cleaning the LCD
Ensure you unplug the power cord before cleaning the LCD. The cabinet as well as the operation panel is made of plastic. Avoid using benzene or thinner, as these can damage the finish on the cabinet.
Do not use volatile agents such as insecticides on the LCD. Do not attach rubber or plastic items on the LCD for long periods of time.
The effects of some of the agents in the plastic may cause damage to the quality or finish of the LCD.
Wipe off dirt gently with a soft flannel cloth.
When the dirt is hard to remove, soak a cloth in a neutral detergent diluted with water, wring the cloth well and then wipe the LCD.
Strong cleaning detergents may discolour, warp or damage the coating on the LCD.
Ensure you test on a small, inconspicuous area on the LCD before using.
Cleaning the exhaust and intake vents
Use a vacuum cleaner to clean dust from the exhaust vent and the intake vent.
HDMI Pin Assignments

PIN#
Signal
1
TMDS Data 2+
2
TMDS Data 2 Shield
3
TMDS Data 2
4
TMDS Data 1+
5
TMDS Data 1 Shield
6
TMDS Data 1
7
TMDS Data 0+
8
TMDS Data 0 Shield
9
TMDS Data 0
10
TMDS Clock+
11
TMDS Clock Shield
12
TMDS Clock
13
CEC
14
No Connect
15
DDC Clock
16
DDC Data
17
Ground
18
+5V Power
19
Hot Plug Detect
20
SHELL