Friday, April 15, 2016

Lenovo ideapad 510 - Disassembling procedure – How to test the battery pack – How to test the charger – How to remove the battery – how to remove the HHD and Optical drive – How to remove the keyboard – Laptop repair and Service

Category: Laptop Repair and Service 

Contents of this article 

  • How to check the battery pack 
  • How to remove the battery pack
  • How to test the charger 

Lenovo ideapad 510

To verify a symptom, follow the steps below:
1. Turn off the computer.
2. Remove the battery pack.
3. Connect the AC adapter.
4. Make sure that power is supplied when you turn on the computer.
5. Turn off the computer.
6. Disconnect the AC adapter and install the charged battery pack.
7. Make sure that the battery pack supplies power when you turn on the computer.
If you suspect a power problem, see the appropriate one of the following power
supply checkouts:
“Checking the AC adapter”
“Checking operational charging”
“Checking the battery pack”
Checking the AC adapter
You are here because the computer fails only when the AC adapter is used.
If the power-on indicator does not turn on, check the power cord of the AC adapter for correct continuity and installation.
To check the AC adapter, follow the steps below:
1. Unplug the AC adapter cable from the computer.
2. Measure the output voltage at the plug of the AC adapter cable. See the following figure:
Note: Output voltage for the AC adapter pin No. 2 may differ from the one you are servicing.
3. If the voltage is not correct, replace the AC adapter.
4. If the voltage is acceptable, do the following:
 Replace the system board.
Note: Noise from the AC adapter does not always indicate a defect.
Checking operational charging
To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator or icon does not light on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon is still off, replace the battery pack.
If the charge indicator still does not light on, replace the system board. Then reinstall the battery pack. If it is still not charged, go to the next section.
Checking the battery pack
Battery charging does not start until the Power Meter shows that less than 95% of the total power remains; under this condition the battery pack can charge to 100% of its capacity. This protects the battery pack from being overcharged or from having a shortened life.
To check your battery, move your cursor to the Power Meter icon in the icon tray of the Windows  taskbar and wait for a moment (but do not click it), and the percentage of battery power remaining is displayed. To get detailed information about the battery, double-click the Power Meter icon.
Note: If the battery pack becomes hot, it may not be able to be charged. Remove it from the computer and leave it at room temperature for a while. After it cools down, reinstall and recharge it.
Restore of factory default
The Lenovo ideapad 510-15ISK/ideapad 510-15IKB computers come with pre-installed OneKey Recovery System. In order to save application files and the initial backed up files of the system, the hard disk in a Lenovo computer includes a hidden partition when it is shipped. If you need to restore the system to the point of your first boot up, just enter Lenovo OneKey Recovery System and run System Recovery.
DISASSEMBLING PROCEDURE 
How to remove Hard disk drive
Remove the screws 1.
Remove the HDD cover in the direction shown by arrow 2.
Lift the hard disk drive slightly in the direction shown by arrow 3. Detach the HDD connector and then remove the hard disk drive from the slot in the direction shown by arrow 4.
How to remove Optical disc drive
Remove the screw 1. Pull the optical drive out in the direction shown by arrow 2.
How to remove Keyboard bezel
Disconnect the touchpad cable connector and the keyboard connector in the directions shown by arrows 1 and 2.
Remove the screws 3 and 4.
Separate the keyboard bezel and upper case in the directions shown by arrows
5 and 6.
Remove the keyboard bezel in the direction shown by arrow 7.
How to remove Battery pack
Remove the screws 1. Then remove the battery pack in the direction shown by arrow 2.