Friday, January 13, 2017

Samsung Full HD LED TV – Samsung UA40B6000VR – How to enter to service mode – Self diagnostic mode

Entering Factory Mode
To enter ‘Service Mode’ Press the remote -control keys in this sequence :
- If you do not have Factory remote - control
POWER OFF > INFO > MENU > MUTE > POWER ON
How to Access Service Mode Using the Customer Remote
Turn the power off and set to stand-by mode
Press the remote buttons in this order; POWER OFF-MUTE-1-8-2-POWER ON to turn the set on.
The set turns on and enters service mode. This may take approximately 20 seconds.
Press the Power button to exit and store data in memory.
- If you fail to enter service mode, repeat steps.
Buttons operations within Service Mode
Menu
Full Menu Display/Move to Parent Menu
Direction Keys UP/ DOWN
Item Selection by Moving the Cursor
Direction Keys LEFT/ RIGHT
Data Increase / Decrease for the Selected Item
Source
Cycles through the active input source that are connected to the unit
White Balance – Calibration
Method of Color Calibration (AV)
1) Apply the NTSC Lattice (N0. 3) pattern signal to the AV IN 1 port
2) Press the Source key to switch to “AV1” mode
3) Enter Service mode
4) Select the “ADC” menu
5) Select the “AV Calibration” menu.
6) In “AV Calibration Off” status, press the “Right Arrow” key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “AV Calibration” status from Failure to Success.
Method of Color Calibration (Component)
1) Apply the 720p Lattice (N0. 6) pattern signal to the Component IN 1 port
2) Press the Source key to switch to “Component1” mode
3) Enter Service mode
4) Select the “ADC” menu
5) Select the “Comp Calibration” menu.
6) In “Comp Calibration Off” status, press the “Right Arrow” key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “Comp Calibration” status from Failure to Success.
Method of Color Calibration (PC)
1) Apply the VESA XGA Lattice (N0. 21) pattern signal to the PC IN port
2) Press the Source key to switch to “PC” mode
3) Enter Service mode
4) Select the “ADC” menu
5) Select the “PC Calibration” menu.
6) In “PC Calibration Off” status, press the “Right Arrow” key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “PC Calibration” status from Failure to Success.
Method of Color Calibration (HDMI)
1) Apply the 720p Lattice (N0. 6) pattern signal to the HDMI1/DVI IN port
2) Press the Source key to switch to “HDMI1” mode
3) Enter Service mode
4) Select the “ADC” menu
5) Select the “HDMI Calibration” menu.
6) In “HDMI Calibration Off” status, press the “ Right Arrow ” key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “HDMI Calibration” status from Failure to Success.
Upgrading the Firmware
1.Insert a USB drive containing the firmware upgrade into the USB Pro port on the side of the TV.
2.If pop up is showed, press the exit or or press the No button. (If you press Yes button, display is changed to Wiselink Pro Menu )
3.Press the MENU button to display the menu.
4.Press the UP or DOWN button to select “Setup”, then press the ENTER button.
5.Press the UP or DOWN button to select “SW Upgrade”, then
press the ENTER button.
Press the ENTER button.
The message “Scanning for USB... It may take up to 30 seconds.” is displayed.
6.The message “Upgrade version ------ to version ------?
The system will be reset after upgrade.” is displayed.
Press the LEFT or RIGHT to select the “OK”, then press the ENTER button.
Self Diagnostic
This is simple test function that judge whether is TV SET’s problem or not.
There are two self-test. Picture and Sound.
Press “Menu > Support > Self Diagnosis”
The message “Picture Test / Sound Test” is displayed
2. Picture Test
1) The message “Does the problem still exist with this test pattern?” is displayed.
2) Press “Yes”. This is a TV SET problem.
3) Press “No”.
This is not a TV SET problem.
The message “If the self diagnosis picture is OK, picture distortion may caused by your external device.
Check connection.
3. Sound Test
1) The message “Does the problem still exist with this sound test?” is displayed.
2) Press “Yes”. This is a TV SET problem.
3) Press “No”.
This is not a TV SET problem.
The message “If the self diagnosis picture is OK, picture distortion may caused by your external device.
Check connection.