17PW46 TFT LCD
SAFETY GUIDANCE
These guidelines are to protect you from
potentially deadly electrical shock hazards as well as the equipment from
accidental damage. Note that the danger to you is not only in your body providing a
conducting path, particularly through your heart. Any involuntary muscle
contractions caused by a shock, while perhaps harmless in themselves, may cause
collateral damage - there are many sharp edges inside this type of equipment as
well as other electrically live parts you may contact accidentally.
The purpose of this set of guidelines is not to frighten you but
rather to make you aware of the appropriate precautions. Repair of TVs,
monitors, microwave ovens, and other consumer and industrial equipment can be
both rewarding and economical. Just be sure that it is also safe!
Don't work alone - in the event of an emergency another person's
presence may be essential.
1.Always keep one hand in your pocket when anywhere around a
powered line-connected or high voltage system. Wear rubber bottom shoes or
sneakers.
2.Don't wear any jewelry or other articles that could accidentally
contact circuitry and conduct current, or get caught in moving parts.
3.Set up your work area away from possible grounds that you may
accidentally contact.
4.Know your equipment: TVs and monitors may use parts of the metal
chassis as ground return yet the chassis may be electrically live with respect
to the earth ground of the AC line. Microwave ovens use the chassis as ground
return for the high voltage. In addition, do not assume that the chassis is a
suitable ground for your test equipment!
5.If circuit boards need to be removed from their mountings, put
insulating material between the boards and anything they may short to. Hold
them in place with string or electrical tape. Prop them up with insulation
sticks - plastic or wood.
6. If you need to probe, solder, or otherwise touch circuits with
power off, discharge (across) large power supply filter capacitors with a 2 W
or greater resistor of 100 to 500 ohms/V approximate value (e.g., for a 200 V
capacitor, use a 20K to 100K ohm resistor). Monitor while discharging and
verify that there is no residual charge with a suitable voltmeter. In a TV or
monitor, if you are removing the high voltage connection to the CRT (to replace
the flyback transformer for example) first discharge the CRT contact (under the
suction cup at the end of the fat HV wire). Use a 1M to 10M ohm 5 W or greater
wattage (for its voltage hold off capability, not power dissipation) resistor
on the end of an insulating stick or the probe of a high voltage meter.
Discharge to the metal frame which is connected to the outside of the CRT.
7. For TVs and monitors in particular, there is the additional
danger of CRT implosion - take care not to bang the CRT envelope with your
tools. An implosion will scatter shards of glass at high velocity in every
direction. There are several tons of force attempting to crush the typical CRT.
While implosion is not really likely even with modest abuse, why take chances?
However, the CRT neck is relatively thin and fragile and breaking it would be
very embarrassing and costly. Always wear eye protection when working around
the back side of a CRT.
8. Connect/disconnect any test leads with the equipment unpowered
and unplugged. Use clip leads or solder temporary wires to reach cramped
locations or difficult to access locations.
9. If you must probe live, put electrical tape over all but the
last 1/16" of the test probes to avoid the possibility of an accidental
short which could cause damage to various components. Clip the reference end of
the meter or scope to the appropriate ground return so that you need to only
probe with one hand.
10. Performe as many tests as possible with power off and the
equipment unplugged. For example, the semiconductors in the power supply
section of a TV or monitor can be tested for short circuits with an ohmmeter.
11. Use an isolation transformer if there is any chance of
contacting line connected circuits. A Variac(tm) is not an isolation
transformer! The use of a GFCI (Ground Fault Circuit Interrupter) protected
outlet is a good idea but will not protect you from shock from many points in a
line connected TV or monitor, or the high voltage side of a microwave oven, for
example. (Note however, that, a GFCI may nuisanse trip at power-on or at other
random times due to leakage paths (like your scope probe ground) or the highly
capacitive or inductive input characteristics of line powered equipment.) A
fuse or circuit breaker is too slow and insensitive to provide any protection
for you or in many cases, your equipment. However, these devices may save your
scope probe ground wire should you accidentally connect it to a live chassis.
12. Don't attempt repair work when you are tired. Not only will
you be more careless, but your primary diagnostic tool - deductive reasoning -
will not be operating at full capacity.
13. Finally, never assume anything without checking it out for
yourself! Don't take shortcuts!
