SERVICE MODE AND POWER SUPPLY CIRCUIT
Category: Lcd Television repair
How to make the Service remote control unit:
Cut “A” portion
of the attached remote control unit as shown in Fig
1. Use the service remote control
unit.
2. Turn the power on.
3. Press the service button on the service remote control unit.
2. Turn the power on.
3. Press the service button on the service remote control unit.
1.Purity Check Mode
This mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels.
1. Enter the Service mode.
2. Each time pressing [7] button on the service remote control unit,
This mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels.
1. Enter the Service mode.
2. Each time pressing [7] button on the service remote control unit,
2. VCOM Adjustment
*This adjustment is required when reparing T-CON CBA
*This adjustment is required when reparing T-CON CBA
Note: Use the service remote control unit
1. Operate the unit for more than 20 minutes.
2. Set the color analyzer and bring the optical receptor to the center on the LCD-Panel surface after zero point calibration as shown above.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
3. Enter the Service mode.
4. Press [3] button on the remote control unit.
5. Press [CH. UP / DOWN] buttons on the remote control unit so that the color analyzer value becomes minimum
1. Operate the unit for more than 20 minutes.
2. Set the color analyzer and bring the optical receptor to the center on the LCD-Panel surface after zero point calibration as shown above.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
3. Enter the Service mode.
4. Press [3] button on the remote control unit.
5. Press [CH. UP / DOWN] buttons on the remote control unit so that the color analyzer value becomes minimum
3. White Balance Adjustment
#This adjustment is required when
reparing T-CON CBA.
Purpose: To mix red, green and blue beams correctly for pure white.
Purpose: To mix red, green and blue beams correctly for pure white.
Symptom of Misadjustment: White becomes bluish or reddish.
1.Operate the unit
for more than 20 minutes.
2.Input the White Purity
2.Input the White Purity
3. Set the color analyzer
to the CHROMA mode and bring the optical receptor to the center on the LCD-Panel
surface after zero point calibration as
shown above.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
4. Enter the Service mode. Press [VOL. DOWN] button on the remote control unit and select “C/D” mode.
shown above.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
4. Enter the Service mode. Press [VOL. DOWN] button on the remote control unit and select “C/D” mode.
5. [CUTOFF]
Press [3] button to select “COB” for Blue Cutoff adjustment. Press [1] button to select “COR” for Red Cutoff adjustment.
Press [3] button to select “COB” for Blue Cutoff adjustment. Press [1] button to select “COR” for Red Cutoff adjustment.
[DRIVE]
Press [6] button to select “DB” for Blue Drive adjustment. Press [4] button to
select “DR” for Red Drive adjustment.
6. In each color mode, press [CH. o / p] buttons to adjust the values of color.
7. Adjust Cutoff and Drive so that the color temperature becomes 12000K (x= 0.272 / y=
0.278 ±0.005).
6. In each color mode, press [CH. o / p] buttons to adjust the values of color.
7. Adjust Cutoff and Drive so that the color temperature becomes 12000K (x= 0.272 / y=
0.278 ±0.005).
How to initialize the LCD
television:
1. Turn the power on.
2. To enter the service mode, press the service button on the service remote control unit.
1. Turn the power on.
2. To enter the service mode, press the service button on the service remote control unit.
# To cancel the
service mode, press [POWER] button on the remote control unit.
3. Press [INFO] button on the remote control unit to initialize the LCD television.
4. "INITIALIZED" will appear in the upper right of the screen. "INITIALIZED" color will change to green from red when initializing is complete.
3. Press [INFO] button on the remote control unit to initialize the LCD television.
4. "INITIALIZED" will appear in the upper right of the screen. "INITIALIZED" color will change to green from red when initializing is complete.
