FUNAI 22FL532/10
LCD TV
SERVICE MODE ADJUSTMENTS
SERVICE MODE
1. Turn the power
on.
2. Press [SOURCE], [2], [5], [8] and [0] buttons on the remote control unit in this order to enter the service mode. The Factory Setting menu appears in the screen.
2. Press [SOURCE], [2], [5], [8] and [0] buttons on the remote control unit in this order to enter the service mode. The Factory Setting menu appears in the screen.
WHITE BALANCE ADJUSTMENT
Purpose: To mix red and blue beams correctly for pure white.
Symptom of Misadjustment: White becomes bluish or reddish.
1. Operate the unit for more than 60 minutes.
2. Input the White Raster (70%=70IRE, 40%=40IRE).
Purpose: To mix red and blue beams correctly for pure white.
Symptom of Misadjustment: White becomes bluish or reddish.
1. Operate the unit for more than 60 minutes.
2. Input the White Raster (70%=70IRE, 40%=40IRE).
3. Enter the
service mode.
4. Press [2] button on the remote control unit to display the “GENERAL SETTING” menu.
5. Select “0 W/B ADJUST” and press [OK] button to display the “W/B ADJUST” menu.
6. Select a color mode (“3 R-GAIN”, “5 B-GAIN”, “7 R-OFFSET” or “9 B-OFFSET”).
7. Set the color analyzer at the CHROMA mode and zero point calibration. Bring the optical receptor pointing at the center of the LCD-Panel.
4. Press [2] button on the remote control unit to display the “GENERAL SETTING” menu.
5. Select “0 W/B ADJUST” and press [OK] button to display the “W/B ADJUST” menu.
6. Select a color mode (“3 R-GAIN”, “5 B-GAIN”, “7 R-OFFSET” or “9 B-OFFSET”).
7. Set the color analyzer at the CHROMA mode and zero point calibration. Bring the optical receptor pointing at the center of the LCD-Panel.
Note: The optical receptor must be set perpendicularly
to the LCD Panel surface.
8. In each color mode, press [ LEFT ] or [ RIGHT ] button to adjust the color temperature becomes 9000°K (x= 0.286 / y= 0.295 ±0.002).
9. Select “10COPY ALL” and press [OK] button.
10. To cancel or to exit from the White Balance Adjustment, press [BACK] button.
8. In each color mode, press [ LEFT ] or [ RIGHT ] button to adjust the color temperature becomes 9000°K (x= 0.286 / y= 0.295 ±0.002).
9. Select “10COPY ALL” and press [OK] button.
10. To cancel or to exit from the White Balance Adjustment, press [BACK] button.
INITIALIZE THE LCD TELEVISION
1. Turn the power
on.
2. Enter the service mode.
2. Enter the service mode.
- To cancel the
service mode, press [BACK] button on the remote control unit.
3. Select “Factory Reset” and [OK] button on the remote control unit. The TV set will go off and turn back on automatically when initialization completes.
3. Select “Factory Reset” and [OK] button on the remote control unit. The TV set will go off and turn back on automatically when initialization completes.
FIRMWARE RENEWAL MODE
Equipment Required
a. USB storage device
b. Remote Control Unit
a. USB storage device
b. Remote Control Unit
Firmware Update Procedure
Preparation
1. Prepare USB storage device.
2. Copy F/W-file to USB storage device.
Note: Make sure to use the blank USB Storage.
3. Make sure that the F/W-file’s name is “BIN_MSD_309.bin”.
Preparation
1. Prepare USB storage device.
2. Copy F/W-file to USB storage device.
Note: Make sure to use the blank USB Storage.
3. Make sure that the F/W-file’s name is “BIN_MSD_309.bin”.
Update
procedure
1. Turn the power on.
2. Insert USB storage device with F/W to TV set.
3. Press the [MENU] button on the remote control unit to display Menu.
4. Select “SETUP”.
5. Select “Software Update (USB)” and press [OK] button. The message “Are you sure?” will appear in the screen.
6. Press [LEFT] button to select “YES”.
7. Updating starts.
Note: Do not turn off the TV set and do not remove the USB storage device while this procedure.
8. The TV set will go off and turn back on automatically when update completes.
Confirmation of update
1. Enter the service mode.
1. Turn the power on.
2. Insert USB storage device with F/W to TV set.
3. Press the [MENU] button on the remote control unit to display Menu.
4. Select “SETUP”.
5. Select “Software Update (USB)” and press [OK] button. The message “Are you sure?” will appear in the screen.
6. Press [LEFT] button to select “YES”.
7. Updating starts.
Note: Do not turn off the TV set and do not remove the USB storage device while this procedure.
8. The TV set will go off and turn back on automatically when update completes.
Confirmation of update
1. Enter the service mode.
2. Press [4]
button on the remote control unit to display the “SW INFORMATION”.
3. Check the “Build Time” section.
3. Check the “Build Time” section.
