SAMSUNG CS21Z30MLMXXST
CRT TV
SERVICE MODE AND POWER SUPPLY CIRCUIT
How to Access Service Mode
1. To enter Service Mode, press the keys on
the remote control according to the following sequence. (in Stand-by status)
Info → Menu → Mute → Power On
When failing to enter Service Mode, repeat the
procedure above.
2. The initial screen of Service Mode
3. Functions of the Keys within Service Mode.
MENU ---- SHOW ALL MENUS
UP AND DOWN--- TO SELECT ITEM
RIGHT AND LEFT -----CHANGE DATA
Adjusting the Picture Size
Since the KS9D chassis has the deflection
settings data within the Factory Data, the picture size has to be adjusted when replacing the Main Board or the VCTi Module, according to the following
procedures.
1. Display the Lion pattern.
2. Press "Info → Menu → Mute → Power On" using the remote control and enter Factory Mode.
3. Enter Adjust Mode.
4. Adjust the VS, VA, HS items so that the
width becomes 92.5 and the height becomes 92.5.
Adjusting the Picture Straight
Lines
1. Display the Cross Hatch pattern
2. Adjust settings other than VA,VH and HS so
that straight lines are displayed without curves.
3. Adjust the V-Linearity and V-SC settings so
that the intervals of the horizontal lines become uniform.
4. When the adjustments are complete, display
the Lion pattern and check that the picture size has not been changed. If there
is no change, finish the adjustments.
Adjusting the Focus
1. Display the CROSS Hatch pattern.
2. Turn the Focus clockwise to the optimal position.
3. Slowly turn the Focus clockwise so that the cross line is the most clearly displayed.
2. Turn the Focus clockwise to the optimal position.
3. Slowly turn the Focus clockwise so that the cross line is the most clearly displayed.
Adjusting the Screen Voltage
1. Select "Info → Menu → Mute → Power On " to enter Factory Mode.
2. Use remocon come into " G2 Adjust" mode by hand or automatically.
3. Turn Screen VR of FBT and confirm the characters below changed to GREEN.
2. Use remocon come into " G2 Adjust" mode by hand or automatically.
3. Turn Screen VR of FBT and confirm the characters below changed to GREEN.
Adjusting the White Balance
1. Initialize all settings to the values
appropriate to the corresponding model.
2. Select "Info → Menu → Mute → Power On " to enter Factory Mode.
3. Initialize all settings to the values appropriate to the corresponding model.
4. Display the Toshiba pattern and adjust the White Balance using CA100 with the coordinates of the corresponding model
2. Select "Info → Menu → Mute → Power On " to enter Factory Mode.
3. Initialize all settings to the values appropriate to the corresponding model.
4. Display the Toshiba pattern and adjust the White Balance using CA100 with the coordinates of the corresponding model
5. Enter Adjust of Service Mode. Adjust
Low/Light.
- Adjust Sub Bright to set Y.
- Adjust B Cutoff to set y.
- Adjust R Cutoff to set x.
6. Enter Adjust of Service Mode. Adjust High/Light.
- Adjust Sub Contrast to set Y.
- Adjust B Drive to set y.
- Adjust R Drive to set x.
7. Check Low/Light and readjust it if its value has been changed.
8. If you have readjusted Low/Light, readjust High/Light until the two values are identical to the coordinates of the corresponding model.
- Adjust Sub Bright to set Y.
- Adjust B Cutoff to set y.
- Adjust R Cutoff to set x.
6. Enter Adjust of Service Mode. Adjust High/Light.
- Adjust Sub Contrast to set Y.
- Adjust B Drive to set y.
- Adjust R Drive to set x.
7. Check Low/Light and readjust it if its value has been changed.
8. If you have readjusted Low/Light, readjust High/Light until the two values are identical to the coordinates of the corresponding model.
Check List for the Screen Voltage
and White Balance Adjustment
1. The Screen Voltage and White Balance are
connected each other, and both of them have to be configured to the correct
values.
2. Adjust the White Balance after the Screen Voltage was adjusted, and check if the Screen Voltage is normal after adjusting the White Balance.
3. If the White Balance is readjusted, check the Screen Voltage again.
4. When the adjustment is finished, check the following checklist.
- If there is a spot on the screen when turning the TV set off/on, adjust the screen Voltage again.
- If there is a ghost line on the screen, adjust the screen Voltage again.
2. Adjust the White Balance after the Screen Voltage was adjusted, and check if the Screen Voltage is normal after adjusting the White Balance.
3. If the White Balance is readjusted, check the Screen Voltage again.
4. When the adjustment is finished, check the following checklist.
- If there is a spot on the screen when turning the TV set off/on, adjust the screen Voltage again.
- If there is a ghost line on the screen, adjust the screen Voltage again.
POWER SUPPLY CIRCUIT
CLICK ON THE IMAGE TO ZOOM IN
