FUNAI 32FL532/10
LCD TV
SERVICE MODE AND T CON BOARD CIRCUIT
INITIALIZING THE TV
1. Turn the power on.
2. Enter the service mode. - To cancel the service mode, press [BACK] button on the remote control unit.
3. Select “Factory Reset” and [OK] button on the remote control unit.
The TV set will go off and turn back on automatically when initialization completes.
2. Enter the service mode. - To cancel the service mode, press [BACK] button on the remote control unit.
3. Select “Factory Reset” and [OK] button on the remote control unit.
The TV set will go off and turn back on automatically when initialization completes.
SERVICE MODE
1. Turn the power on.
2. Press [SOURCE], [2], [5], [8] and [0] buttons on the remote control unit in this order to enter the service mode. The Factory Setting menu appears in the screen
1. Turn the power on.
2. Press [SOURCE], [2], [5], [8] and [0] buttons on the remote control unit in this order to enter the service mode. The Factory Setting menu appears in the screen
White Balance Adjustment
Purpose: To mix red and blue beams correctly for
pure white.
Symptom of Misadjustment: White becomes bluish or reddish.
1. Operate the unit for more than 60 minutes.
2. Input the White Raster (70%=70IRE, 40%=40IRE)
Purpose: To mix red and blue beams correctly for
pure white.
Symptom of Misadjustment: White becomes bluish or reddish.
1. Operate the unit for more than 60 minutes.
2. Input the White Raster (70%=70IRE, 40%=40IRE)
3. Enter the service mode.
4. Press [2] button on the remote control unit to display the “GENERAL SETTING” menu.
5. Select “0 W/B ADJUST” and press [OK] button to display the “W/B ADJUST” menu.
6. Select a color mode (“3 R-GAIN”, “5 B-GAIN”, “7 R-OFFSET” or “9 B-OFFSET”).
7. Set the color analyzer at the CHROMA mode and zero point calibration. Bring the optical receptor pointing at the center of the LCD-Panel.
4. Press [2] button on the remote control unit to display the “GENERAL SETTING” menu.
5. Select “0 W/B ADJUST” and press [OK] button to display the “W/B ADJUST” menu.
6. Select a color mode (“3 R-GAIN”, “5 B-GAIN”, “7 R-OFFSET” or “9 B-OFFSET”).
7. Set the color analyzer at the CHROMA mode and zero point calibration. Bring the optical receptor pointing at the center of the LCD-Panel.
8. In each color mode, press [<] or [>]
button to adjust the color temperature becomes 12000°K (x= 0.272 / y= 0.278 ±0.002).
9. Select “10COPY ALL” and press [OK] button.
10. To cancel or to exit from the White Balance Adjustment, press [BACK] button.
9. Select “10COPY ALL” and press [OK] button.
10. To cancel or to exit from the White Balance Adjustment, press [BACK] button.
Firmware Update Procedure
1. Prepare USB storage device.
2. Copy F/W-file to USB storage device.
2. Copy F/W-file to USB storage device.
Note: Make sure to use the blank USB Storage.
3. Make sure that the F/W-file’s name is “BIN_MSD_309.bin”.
Update procedure3. Make sure that the F/W-file’s name is “BIN_MSD_309.bin”.
1. Turn the power on.
2. Insert USB storage device with F/W to TV set.
3. Press the [MENU] button on the remote control unit to display Menu.
4. Select “SETUP”.
5. Select “Software Update (USB)” and press [OK] button. The message “Are you sure?” will appear in the screen.
6. Press [LEFT] button to select “YES”.
7. Updating starts.
Note: Do not turn off the TV set and do not remove the USB storage device while this procedure.
8. The TV set will go off and turn back on automatically when update completes.
Confirmation of update
1. Enter the service mode.
2. Press [4] button on the remote control unit to display the “SW INFORMATION”.
3. Check the “Build Time” section
T CON BOARD CIRCUIT
CLICK ON THE IMAGE TO ZOOM IN
