SAMSUNG LE32D400 - UE32D400 - UE40D500
LED TV
SERVICE MODE
Entering Factory Mode
To enter ‘Service Mode’ Press the remote -control keys in this sequence :
- If you do not have Factory remote – control
To enter ‘Service Mode’ Press the remote -control keys in this sequence :
- If you do not have Factory remote – control
Power OFF > INFO > MENU > MUTE > Power ON
- If you have Factory remote – control
INFO > FACTORY KEY
How to Access Service Mode Using the Customer Remote
1. Turn the power off and set to stand-by mode.
2. Press the remote buttons in this order; POWER OFF- INFO - MENU - MUTE to turn the set on.
3. The set turns on and enters service mode. This may take approximately 20 seconds.
4. Press the Power button to exit and store data in memory.
- If you fail to enter service mode, repeat steps 1 and 2 above.
5. Initial SERVICE MODE DISPLAY State
2. Press the remote buttons in this order; POWER OFF- INFO - MENU - MUTE to turn the set on.
3. The set turns on and enters service mode. This may take approximately 20 seconds.
4. Press the Power button to exit and store data in memory.
- If you fail to enter service mode, repeat steps 1 and 2 above.
5. Initial SERVICE MODE DISPLAY State
* How to enter the hidden factory mode.
a. into the factory mode
b. move the tap to Advanced
c. key input : 0 + 0 + 0 + 0
** hidden menu : Advanced
a. into the factory mode
b. move the tap to Advanced
c. key input : 0 + 0 + 0 + 0
** hidden menu : Advanced
White Ratio (Balance) Adjustment
1. You can adjust the white ratio in factory mode (1:Calibration, 3:White-Balance).
2. Since the adjustment value and the data value vary depending on the input source, you have to adjust these in CVBS,
Component 1 and HDMI 1 modes.
3. The optimal values for each mode are confiured by default.
1. You can adjust the white ratio in factory mode (1:Calibration, 3:White-Balance).
2. Since the adjustment value and the data value vary depending on the input source, you have to adjust these in CVBS,
Component 1 and HDMI 1 modes.
3. The optimal values for each mode are confiured by default.
It varies with Panel’s size and Specifiation.
- Equipment : CS-210
- Pattern: MIK K-7256 #92 "Flat W/B Pattern" as standard
- Use other equipment only after comparing the result with that of the Master equipment.
- Set Aging time : 60min
- Calibration and Manual setting for WB adjustment
- Equipment : CS-210
- Pattern: MIK K-7256 #92 "Flat W/B Pattern" as standard
- Use other equipment only after comparing the result with that of the Master equipment.
- Set Aging time : 60min
- Calibration and Manual setting for WB adjustment
HDMI : Calibration at #24 Chessboard Pattern > Manual adjustment #92 pattern (720p)
COMP: Calibration at #24 Chessboard Pattern > Manual adjustment at #92 pattern (720p)
CVBS: Calibration at #24 Chessboard Pattern > Manual adjustment at #92 pattern (PAL)
COMP: Calibration at #24 Chessboard Pattern > Manual adjustment at #92 pattern (720p)
CVBS: Calibration at #24 Chessboard Pattern > Manual adjustment at #92 pattern (PAL)
How To Upgrade Sub Micom
Sub S/W (in Factory mode)
If you don't have DDC Manager, Use this method.
1. Into the Factory Mode.
2. Select "SVC". (Use RIGHT ARROW button.)
3. Select "MICOM UPGRADE off". (use RIGHT ARROW button.)
4. If message change from "off" to "wait", TV is upgrading Sub S/W. (It takes about 5 min.)
5. If update completes, TV set will booting automatically
Sub S/W (in Factory mode)
If you don't have DDC Manager, Use this method.
1. Into the Factory Mode.
2. Select "SVC". (Use RIGHT ARROW button.)
3. Select "MICOM UPGRADE off". (use RIGHT ARROW button.)
4. If message change from "off" to "wait", TV is upgrading Sub S/W. (It takes about 5 min.)
5. If update completes, TV set will booting automatically
USB Download Method (Main SW & e-Manual)
Samsung may offer upgrades for TV’s fimware in the future. Upgrades will be possible by connecting a USB drive to the USB port located on your TV.
1. Insert a USB drive containing the fimware (T-MSU4DEUC) upgrade into the USB port on the rear of the TV.
2. Press the MENU button to display the menu. Press the UP or DOWN button to select "Support", then press the ENTER button.
3. Press the UP or DOWN button to select "Software Upgrade", then press the ENTER button to select "By USB". The message "Scanning for USB. It may take up to 1 minute." is displayed.
4. The message "Upgrade version XXXX to version XXXX? The system will be reset after upgrade." is displayed. Press the LEFT or RIGHT to select the "OK", then press the ENTER button.
Please be careful to not disconnect the power or remove the USB drive while upgrades are being applied. The TV will turn off and turn on automatically after completing the fimware upgrade. Please check the fimware version after the upgrades are complete. When software is upgraded, video and audio settings you have made will return to their default (factory) settings. We recommend you write down your settings so that you can easily reset them after the upgrade.
