MITSUBISHI ELECTIRC WD-60C10 - WD-65C10 - WD-73C10 -WD-60638 - WD-65638 - WD-73638 - WD-60738 - WD-65738 - WD-73738 -- WD-82738 - WD-65838 - WD-73838 - WD-82838
DLP PROJECTION TELEVISION
SERVICE MODE LED BLINKING CODE AND POWER SUPPLY CIRCUIT
APPLICABLE CHASSIS
V43C Chassis
WD-60C10
WD-65C10
WD-73C10
WD-65C10
WD-73C10
V43 Chassis
WD-60638
WD-65638
WD-73638
WD-65638
WD-73638
V43+ Chassis
WD-60738
WD-65738
WD-73738
WD-82738
WD-65738
WD-73738
WD-82738
V43++ Chassis
WD-65838
WD-73838
WD-82838
WD-73838
WD-82838
SELF DIAGNOSTICS
A blinking red and yellow Status LED will indicate an Error Code that can help determine the cause of a circuit failure.
• The number of Red blinks indicates the value of the MSD (tens digit) of the Error Code.
• The number of Yellow blinks indicates the value of the LSD (ones digit) of the Error Code.
Example: If the Error Code is “37”, the LED will continuously blink Red three times, followed by blinking Yellow seven times.
A blinking red and yellow Status LED will indicate an Error Code that can help determine the cause of a circuit failure.
• The number of Red blinks indicates the value of the MSD (tens digit) of the Error Code.
• The number of Yellow blinks indicates the value of the LSD (ones digit) of the Error Code.
Example: If the Error Code is “37”, the LED will continuously blink Red three times, followed by blinking Yellow seven times.
See the following for a list of Error Codes.
To perform a System Reset, press and hold the Power button for 10 seconds. Or, unplug the set for 10 seconds then restore power.
To perform a System Reset, press and hold the Power button for 10 seconds. Or, unplug the set for 10 seconds then restore power.
ERROR CODES
Code
|
Description
|
Most Likely Cause
|
16
|
LAMP-EN Detection
|
Check Color Wheel / Check J6
& J7 circuitry /
Engine Failure |
17
|
I2C Communication loss between
TV Micro and Engine
|
Loss of 12V from PWB-POWER to
Engine /
Check PE & PE2 circuitry Engine Failure, PWB-MAIN Failure |
18
|
Engine will not accept data
(ASIC-READY signal from Engine is not detected). |
LDVS circuitry
Engine Failure |
24
|
Sirocco fan (Lamp fan) rotation
not detected.
|
Check Sirocco Fan / Check J8
circuitry
|
34
|
Lamp turns Off while the TV is
playing.
Lamp Failure Lamp Enable signal from engine is lost. |
Lamp Cartridge Failure
|
36
|
Exhaust Fan rotation not
detected.
|
Check Exhaust Fan / Check J4
circuitry
|
37
|
Engine (DMD) fan rotation not
detected.
|
Check DMD Fan / Check J5
circuitry
|
44
|
LVDS cable between PWB-MAIN and
Engine not detected.
|
Check LVDS Cable & circuitry
|
48
|
PON-SHORT 3.3V or 5V switched
supply short
|
PWB-MAIN Failure
|
57
|
Ballast communication problem
(ballast to chassis)
|
Loss of 340V from PWB-POWER to
Ballast /
Check PL & CJ1 circuitry Loss of communications between PWB-MAIN and Ballast / Check FB & CJ3 circuitry Ballast Failure |
66
|
Lamp did not turn on at P-ON
sequence
(No Lamp inserted) (Disconnected cable between ballast and lamp) (Lamp-Enable goes to PWB-MAIN but not to Ballast) |
Check CJ4 circuitry
No Lamp Inserted. HV connection or lead wire to lamp. Lamp Cartridge Failure |
Activating the Service Menu
V43C & V43
For the V43C & V43 chassis, all service functions except Data Transfer are included under the Service Menu.
1. Press the <MENU> button on a remote control. (The Customer Menu will appear.) 2. Press the buttons <2-4-7-0>. (The Service Menu will appear.)
V43C & V43
For the V43C & V43 chassis, all service functions except Data Transfer are included under the Service Menu.
1. Press the <MENU> button on a remote control. (The Customer Menu will appear.) 2. Press the buttons <2-4-7-0>. (The Service Menu will appear.)
V43+ & V43++
1. Press the <MENU> button on a remote control. (The Customer Menu will appear.)
2. Press the buttons <2-4-5-7>. (The Service Menu will appear.)
Test Pattern Activation
V43C & V43
1. When in the Service Menu select “Test Picture” <ENTER> <0,1,2,3,4 or 5> to select specific patterns.
2. When in the Service Menu select “Calibration” <ENTER> <1-1-1-1>. Use <CH UP> and <CH DOWN> to toggle between patterns.
V43+ & V43++
1. When in the Service Menu, press Play to activate the internal test patterns (no indication will be displayed initially). Use FWD and RWD to toggle between patterns.
2. Press Play a second time and use FWD and RWD to access additional patterns.
3. Press Play again to toggle back to the previous patterns.
V43C & V43
1. When in the Service Menu select “Test Picture” <ENTER> <0,1,2,3,4 or 5> to select specific patterns.
2. When in the Service Menu select “Calibration” <ENTER> <1-1-1-1>. Use <CH UP> and <CH DOWN> to toggle between patterns.
V43+ & V43++
1. When in the Service Menu, press Play to activate the internal test patterns (no indication will be displayed initially). Use FWD and RWD to toggle between patterns.
2. Press Play a second time and use FWD and RWD to access additional patterns.
3. Press Play again to toggle back to the previous patterns.
Adjusting Data
After selecting an adjustment item, use the Navigation arrows or other buttons indicated in the adjustment procedure to perform the adjustment.
After selecting an adjustment item, use the Navigation arrows or other buttons indicated in the adjustment procedure to perform the adjustment.
Saving Data
Press <ENTER> to save the adjustment data.
V43C & V43, The Status LED will turn red for about 1 second.
V43+ & V43++, The menu display will turn red for approximately one second.
Note: If the circuit adjustment mode is terminated without pressing <ENTER>, changes in adjustment data are not saved.
Press <ENTER> to save the adjustment data.
V43C & V43, The Status LED will turn red for about 1 second.
V43+ & V43++, The menu display will turn red for approximately one second.
Note: If the circuit adjustment mode is terminated without pressing <ENTER>, changes in adjustment data are not saved.
Exiting the Service Menu
Press <EXIT> to quit.
Press <EXIT> to quit.
Horizontal and Vertical Position Adjustment
V43C & V43
1. Enter the Service Menu <MENU><2-4-7-0> .
2. Select “Calibration” <ENTER>. The raster will blank out.
3. Enter the H & V Position adjustment by pressing <2-8-4-6>. The geometry pattern below will be displayed and the STATUS LED will blink Green at a 1 second interval during the alignment..
1. Enter the Service Menu <MENU><2-4-7-0> .
2. Select “Calibration” <ENTER>. The raster will blank out.
3. Enter the H & V Position adjustment by pressing <2-8-4-6>. The geometry pattern below will be displayed and the STATUS LED will blink Green at a 1 second interval during the alignment..
4. Use the Navigation <UP,DOWM.LEFT,RIGH>
buttons to center the display.
5. Press <ENTER> to save the adjustment data. The STATUS LED will turn Red while the data is saved
5. Press <ENTER> to save the adjustment data. The STATUS LED will turn Red while the data is saved
Horizontal and Vertical Position Adjustment
V43+ & V43++
1. Enter the Service Menu <MENU><2-4-5-7> .
2. Select the Geometry Test Pattern Play Rewind x2.
3. If necessary, use the <VIDEO> button to select the adjustment, “1.HVPOS”.
1. Enter the Service Menu <MENU><2-4-5-7> .
2. Select the Geometry Test Pattern Play Rewind x2.
3. If necessary, use the <VIDEO> button to select the adjustment, “1.HVPOS”.
4. After selecting the HVPOS adjustment item,
use the Navigation <UP,DOWM.LEFT,RIGH> buttons to center the display.
5. Press <ENTER> to save the adjustment data. The on-screen display will flash red while the data is saved.
5. Press <ENTER> to save the adjustment data. The on-screen display will flash red while the data is saved.
Index Delay Adjustment (Perform
after color wheel replacement)
V43C & V43
1. Enter the Service Menu <MENU><2-4-7-0> .
2. Select “Calibration” <ENTER>. The raster will blank out.
3. Enter the Index Delay adjustment by pressing <2-5-8-0>. The ramp pattern below will be displayed and the
STATUS LED will blink Green at a 1 second interval during the alignment..
V43C & V43
1. Enter the Service Menu <MENU><2-4-7-0> .
2. Select “Calibration” <ENTER>. The raster will blank out.
3. Enter the Index Delay adjustment by pressing <2-5-8-0>. The ramp pattern below will be displayed and the
STATUS LED will blink Green at a 1 second interval during the alignment..
4. Use the Navigation <UP,DOWN> buttons to adjust the ramp
pattern color bars for the smoothest transition from dark to bright.
5. Press <ENTER> to save the adjustment data. The STATUS LED will turn Red while the data is saved.
5. Press <ENTER> to save the adjustment data. The STATUS LED will turn Red while the data is saved.
Index Delay Adjustment (Perform after
color wheel replacement)
V43+ & V43++
1. Enter the Service Menu <MENU><2-4-5-7> .
2. Select the Ramp Pattern PLAY >REWIND x3.
3. Use the <VIDEO> button to select the adjustment, “60.IDL”
V43+ & V43++
1. Enter the Service Menu <MENU><2-4-5-7> .
2. Select the Ramp Pattern PLAY >REWIND x3.
3. Use the <VIDEO> button to select the adjustment, “60.IDL”
4. After selecting the IDL adjustment item, use
the Navigation <UP,DOWN> buttons to adjust the ramp pattern color bars for the
smoothest transition from dark to bright.
5. Press <ENTER> to save the adjustment data. The on-screen display will turn red while the data is saved.
5. Press <ENTER> to save the adjustment data. The on-screen display will turn red while the data is saved.
Manual Geometry Alignment
V43C & V43
Entering the Manual Geometry Alignment Mode
1. Activate the Service Menu <MENU><2-4-7-0>.
2. Select “Calibration” <ENTER>. A “dot pattern” will be displayed.
V43C & V43
Entering the Manual Geometry Alignment Mode
1. Activate the Service Menu <MENU><2-4-7-0>.
2. Select “Calibration” <ENTER>. A “dot pattern” will be displayed.
Enter the Manual Geometry Alignment mode by
pressing <1-3-9-7>. The Manual Geometry Alignment Pattern will appear
Manual Geometry Alignment
V43+ & V43++
Entering the Manual Geometry Alignment Mode
1. Activate the Service Mode <MENU><2-4-5-7>.
2. From the Service Menu, press the <0> button. The Data Transfer & Geometry Menu will appear.
V43+ & V43++
Entering the Manual Geometry Alignment Mode
1. Activate the Service Mode <MENU><2-4-5-7>.
2. From the Service Menu, press the <0> button. The Data Transfer & Geometry Menu will appear.
3. Use the <UP,DOWN> buttons to select
“MANUAL GEOMETRY ALIGNMENT” <ENTER>. The Manual Geometry Alignment Pattern will appear
POWER SUPPLY CIRCUITS
V43C & V43
