PHLIPS BDP8000/12/51
3D BLU RAY PLAYER
SERVICE MODE OPTICAL PICKUP AND MAIN BROAD ALIGNMENT – POWER SUPPLY AND SOFTWARE UPDATE
Preparation to upgrade software
1)Start the CD burning software & create a folder named "UPG_ALL",
2)Then copy the Bin file (BDP_8000_S_B.bin ) into it,
3)Burn the data onto the blank CD or USB.
4)If the model is BDP8000,must use (BDP_8000_S_X.bin )to upgrade x(A,B,C)if the model BD code is A, X=A, BD code is B , X =B BD=code is C ,X=C
Procedure for software upgrade
Upgrade software via Disc
1) Power on the set and insert the prepared Upgrade CDR.
2) The set will starts reading disc & response with the following display TV screen: Now searching for upgrade software!
Please wait…!
1)Start the CD burning software & create a folder named "UPG_ALL",
2)Then copy the Bin file (BDP_8000_S_B.bin ) into it,
3)Burn the data onto the blank CD or USB.
4)If the model is BDP8000,must use (BDP_8000_S_X.bin )to upgrade x(A,B,C)if the model BD code is A, X=A, BD code is B , X =B BD=code is C ,X=C
Procedure for software upgrade
Upgrade software via Disc
1) Power on the set and insert the prepared Upgrade CDR.
2) The set will starts reading disc & response with the following display TV screen: Now searching for upgrade software!
Please wait…!
3) Press <OK> button to confirm, then screen will
display : An upgrade software has been found! Start upgrade with
version:WKXXX.X?
4) Press Right cursor button to choose "Start",
then press <OK>;
5) The software will updagrde and screen will display as below: Upgrade is ongoing, Please wait… Please do not unplug or switch off the device.
6) The screen will display as below when upgrading complete: Upgrade has completed successfully! Power off after 5s.
5) The software will updagrde and screen will display as below: Upgrade is ongoing, Please wait… Please do not unplug or switch off the device.
6) The screen will display as below when upgrading complete: Upgrade has completed successfully! Power off after 5s.
5) Restart the set.
Upgrade softwar via network:
1) Setup the network connection (See "Getting started">"Set up
network").
2) In the Home menu, select <Setting>-<Advanced Setup>-
<Software Download>-<Network>.
* You are prompted to start upgrading processes if upgrade media is detected.
3) Follow the instructions on the TV screen to confirm update operation.
* Once software updated is complete, this player automatically truns off to standby.
4) Disconnect the power cord for a few seconds and connect again to turn on the player.
Update software via USB Flash Drive:
1) Go to philips/support to check if the latest software version is available for this player.
2) Download the software onto a USB flash drive.
3) Insert the USB flash drive to the USB jack of the rear panel.
4) In the Home menu, select <Setup>-<Advanced Setup>-<Software Updade >-<USB>.
5) Follow the instructions on the TV screen to confrim update operation.
*Once software update is complete, this player automatically turns to standby.
6) Disconnect the power cord for a few seconds and connect again to turn on the player.
1) Setup the network connection (See "Getting started">"Set up
network").
2) In the Home menu, select <Setting>-<Advanced Setup>-
<Software Download>-<Network>.
* You are prompted to start upgrading processes if upgrade media is detected.
3) Follow the instructions on the TV screen to confirm update operation.
* Once software updated is complete, this player automatically truns off to standby.
4) Disconnect the power cord for a few seconds and connect again to turn on the player.
Update software via USB Flash Drive:
1) Go to philips/support to check if the latest software version is available for this player.
2) Download the software onto a USB flash drive.
3) Insert the USB flash drive to the USB jack of the rear panel.
4) In the Home menu, select <Setup>-<Advanced Setup>-<Software Updade >-<USB>.
5) Follow the instructions on the TV screen to confrim update operation.
*Once software update is complete, this player automatically turns to standby.
6) Disconnect the power cord for a few seconds and connect again to turn on the player.
Read out the software versions to confirm
upgrading
1) Power on the set and open the tray door.
2) Press <Home> button on the reomote control.
3) Select <Setup>, then press <OK>.
4) Select <Advanced Setup>, press right cursor to choose
<Version Info.>, then press <OK>, the software version and other information will display on the TV screen as below: Model:BDP8XXX Versions:
Philips web
1) Power on the set and open the tray door.
2) Press <Home> button on the reomote control.
3) Select <Setup>, then press <OK>.
4) Select <Advanced Setup>, press right cursor to choose
<Version Info.>, then press <OK>, the software version and other information will display on the TV screen as below: Model:BDP8XXX Versions:
Philips web
How to proceed OPU and mainboard alignment ?
1. Record the 1D barcode with barcode reader or all the 32 digits of label a ached on the top of original loader (if replaced with a new main board) or new loader spare part (if replaced with a new loader
1. Record the 1D barcode with barcode reader or all the 32 digits of label a ached on the top of original loader (if replaced with a new main board) or new loader spare part (if replaced with a new loader
Note: to skip this step for the loader without 1D barcode
label.
2. Power on the set and connect with TV, press “5” “1” “7”
“7” by remote control when in the HOME menu, it will enter a special menu with
7 options.
Use “Up” and “Down” button by remote control to select op on
“[5] Repair (or Service)”.
3. When you see this screen, please plug a USB drive. After
that press “Enter” to install
barcode.
barcode.
Note: 1) We need to plug-in USB drive otherwise you cannot
proceed to next step. This is for saving data in case of failure happen, and
then loader supplier could use this information on to investigate.
2) Due to ny current on USB port, a blank USB drive is recommended. If using MP3 or MP4 device, it should be full charged, or the TV display will show “Fail: Try Again”.
2) Due to ny current on USB port, a blank USB drive is recommended. If using MP3 or MP4 device, it should be full charged, or the TV display will show “Fail: Try Again”.
4. Input alphanumeric code by remote control, then press
“Back” and then press “Enter” to save the setting
Note: Try to input any one of 4 codes as below if no 1D
barcode label until it works .
1). B6B412
2). 278412
3). 06D412
4). A55412
1). B6B412
2). 278412
3). 06D412
4). A55412
5. If setting is saved successfully, it will display “Pas”
on screen. Otherwise, it will display “Fail” on screen. If “fail”, confirm the
alphanumeric code information again . (this is like a password, failed if we
input the wrong password)
6. Press “Stop” key on remote control to go back the HOME
menu again, and then press “5” “1” “7” “7” by remote control to enter a special
menu with 6 options again. Use “Up” and “Down” bu on by remote control to select
op on “[6] Laser Check”
7. If the cable is well connected and welded protection
point is ok, it will display “Passe” on screen.
8. Restart the player, test with CD, DVD, BD disc. If ok,
the repair procedure is finished!
SMPS POWER SUPPLY CIRCUIT
CLICK ON THE IMAGES TO ZOOM IN
