FUNAI LT850-M26
SERVICE MODE AND POWER SUPPLY CIRCUIT
Service mode:
1. Turn the power on.
2. Press [MENU] button to display Setup menu.
3. Select “Software” in “OTHERS” and press [OK] button.
4. Press [0], [4], [2], [5], [7], [4] and [ i ] buttons on the remote control unit in this order. The following screen appears.
1. Turn the power on.
2. Press [MENU] button to display Setup menu.
3. Select “Software” in “OTHERS” and press [OK] button.
4. Press [0], [4], [2], [5], [7], [4] and [ i ] buttons on the remote control unit in this order. The following screen appears.
Purity Check Mode
This mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels.
1. Enter the Service mode.
2. Each time pressing [7] button on the remote control unit, the display changes
This mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels.
1. Enter the Service mode.
2. Each time pressing [7] button on the remote control unit, the display changes
3. To cancel or
to exit from the Purity Check Mode, press [BACK] button.
VCOM Adjustment
1. Operate the
unit for more than 20 minutes.
2. Set the color analyzer and bring the optical receptor to the center on the LCD-Panel surface after zero point calibration as shown above.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
3. Enter the Service mode.
4. To enter the “VCOM-2 adjustment mode”, press [3] button on the remote control unit.
To enter the “VCOM-1 adjustment mode”, press [2] button on the remote control unit.
5. Press [P UP/DOWN ] buttons on the remote control unit so that the color analyzer value becomes minimum.
6. To cancel or to exit from the VCOM Adjustment, press [BACK] button.
2. Set the color analyzer and bring the optical receptor to the center on the LCD-Panel surface after zero point calibration as shown above.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
3. Enter the Service mode.
4. To enter the “VCOM-2 adjustment mode”, press [3] button on the remote control unit.
To enter the “VCOM-1 adjustment mode”, press [2] button on the remote control unit.
5. Press [P UP/DOWN ] buttons on the remote control unit so that the color analyzer value becomes minimum.
6. To cancel or to exit from the VCOM Adjustment, press [BACK] button.
White Balance Adjustment
Purpose: To mix red, green and blue beams correctly
for pure white.
Symptom of Misadjustment: White becomes bluish or reddish
Purpose: To mix red, green and blue beams correctly
for pure white.
Symptom of Misadjustment: White becomes bluish or reddish
1. Operate the
unit for more than 20 minutes.
2. Input the White Raster(70%=70IRE, 40%=40IRE).
2. Input the White Raster(70%=70IRE, 40%=40IRE).
3. Set the color
analyzer to the CHROMA mode and bring the optical receptor to the center on the
LCD-Panel surface after zero point calibration as shown above.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
4. Enter the Service mode. Press [ Volume -] button on the remote control unit and select “C/D” mode.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
4. Enter the Service mode. Press [ Volume -] button on the remote control unit and select “C/D” mode.
5. [CUTOFF]
Press [1] button to select “COR” for Red Cutoff adjustment. Press [3] button to select “COB” for Blue Cutoff adjustment.
[DRIVE]
Press [4] button to select “DR” for Red Drive adjustment. Press [6] button to select “DB” for Blue
Drive adjustment.
6. In each color mode, press [P / ] buttons to adjust the values of color.
7. Adjust Cutoff and Drive so that the color temperature becomes 9200°K (x= 0.286 / y= 0.295 ±0.005).
8. To cancel or to exit from the White Balance Adjustment, press [BACK] button.
Press [1] button to select “COR” for Red Cutoff adjustment. Press [3] button to select “COB” for Blue Cutoff adjustment.
[DRIVE]
Press [4] button to select “DR” for Red Drive adjustment. Press [6] button to select “DB” for Blue
Drive adjustment.
6. In each color mode, press [P / ] buttons to adjust the values of color.
7. Adjust Cutoff and Drive so that the color temperature becomes 9200°K (x= 0.286 / y= 0.295 ±0.005).
8. To cancel or to exit from the White Balance Adjustment, press [BACK] button.
INITIALIZE THE LCD TELEVISION
How to initialize the LCD television:
1. Turn the power on.
2. Enter the service mode.
How to initialize the LCD television:
1. Turn the power on.
2. Enter the service mode.
- To cancel the
service mode, press [ ] button on the remote control unit.
3. Press [ i ] button on the remote control unit to initialize the LCD television.
4. "INITIALIZED" will appear in the upper right of the screen. "INITIALIZED" color will change to green from red when initializing is complete.
3. Press [ i ] button on the remote control unit to initialize the LCD television.
4. "INITIALIZED" will appear in the upper right of the screen. "INITIALIZED" color will change to green from red when initializing is complete.
Firmware Update Procedure
[Check the current version]
1. Press [MENU] button on the remote control unit to display the menu mode.
2. Press [UP] or [DOWN] to select “OTHERS”, then press [OK] button.
3. Press [UP] or [DOWN] to select “Software”, then press [OK] button.
The current FW version will be displayed.
[Check the current version]
1. Press [MENU] button on the remote control unit to display the menu mode.
2. Press [UP] or [DOWN] to select “OTHERS”, then press [OK] button.
3. Press [UP] or [DOWN] to select “Software”, then press [OK] button.
The current FW version will be displayed.
[Preparation]
1. Prepare USB storage device.
2. Copy F/W-file (ecc file) to USB storage device.
Note: Make sure to use the blank USB Storage.
3. Rename the F/W-file’s name. Step1. Add the “_F” at the end of the name. (If the file name in USB says “ZF6731915NOS-030-05.ecc”, the new file name should be “ZF6731915NOS-030-05_F.ecc”.)
Step2. The 6th and 7th digit of the file name indicate the size of TV. If the size of your TV and the file name were not the same, you must change the file name.
1. Prepare USB storage device.
2. Copy F/W-file (ecc file) to USB storage device.
Note: Make sure to use the blank USB Storage.
3. Rename the F/W-file’s name. Step1. Add the “_F” at the end of the name. (If the file name in USB says “ZF6731915NOS-030-05.ecc”, the new file name should be “ZF6731915NOS-030-05_F.ecc”.)
Step2. The 6th and 7th digit of the file name indicate the size of TV. If the size of your TV and the file name were not the same, you must change the file name.
[Update procedure]
1. Plug in the AC power cord.
2. Press [ POWER ] button on the remote control unit to turn off (standby).
3. Check “STAND BY” indicator (Red LED) lighting.
4. Insert USB storage device with F/W to TV set.
5. Press [ POWER ] button to turn on.
6. After approximately 70 seconds, the following will appear on the screen and the update begins automatically.
1. Plug in the AC power cord.
2. Press [ POWER ] button on the remote control unit to turn off (standby).
3. Check “STAND BY” indicator (Red LED) lighting.
4. Insert USB storage device with F/W to TV set.
5. Press [ POWER ] button to turn on.
6. After approximately 70 seconds, the following will appear on the screen and the update begins automatically.
Note: Do not turn off the TV set and do
not remove the USB storage device while this procedure.
7. Press [ POWER ] button to turn off (standby).
8. Check “STAND BY” indicator (Red LED) lighting.
9. Remove USB storage device from TV set.
10. Press [ POWER ] button to turn on.
8. Check “STAND BY” indicator (Red LED) lighting.
9. Remove USB storage device from TV set.
10. Press [ POWER ] button to turn on.
POWER SUPPLY CIRCUIT
CLICK ON THE IMAGE TO ZOOM IN
