PIONEER BDP-170-K
SERVICE MODE AND FIRMWARE UPDATE
SERVICE
MODE
In Service
Mode, there is a mixture of Design and Development, Production Line Menu and
Service Menu.
Here, menu items that are usable in Service and instructions are listed. Only use the menu explained in this document. Others are for Design and Product lines. Each item of Service mode can be quit by pressing the [STOP] button. However, to check operations such as normal playback, turn the unit OFF then back ON again.
Here, menu items that are usable in Service and instructions are listed. Only use the menu explained in this document. Others are for Design and Product lines. Each item of Service mode can be quit by pressing the [STOP] button. However, to check operations such as normal playback, turn the unit OFF then back ON again.
HOW
TO ENTER SERVICE MODE
1. Press [HOME
MENU] button on the remote controller and select "Initial Setup" from
the home menu.
2. Pressing the
number buttons on the remote control in the following order [5] > [1] > [7] > [7] will display the Menu screen.
(If it does not appear, slowly press the number keys with a 1 second interval.)
(If it does not appear, slowly press the number keys with a 1 second interval.)
Laser Check
Verifies the
output value of each laser diode inside the pick-up area. Implement according
to the following procedures.
1 Select "[4] Laser Check" with the b button from the
Service Mode screen and press the [ENTER] button. (perform without disc in
tray)
2 After a few seconds, measurement and judgment results will be displayed, as shown below. If all measurement (Meas) values are 1/3 or greater or less than triple the target values (hex), [Pass] will be displayed.
If any of the measurement values is out of this range, [NG] will be displayed.
2 After a few seconds, measurement and judgment results will be displayed, as shown below. If all measurement (Meas) values are 1/3 or greater or less than triple the target values (hex), [Pass] will be displayed.
If any of the measurement values is out of this range, [NG] will be displayed.
Enter SP Mode
There are 17
items in the SP Mode, the main items being for Production line and
Design/Development. The following is to explain items usable in Service. Other
items require time for completion, or are not suited for Service purposes. If
you select them by mistake, press the [STOP] button to end that item you
accidentally selected. (none of the items will affect the main unit)
[ Instructions ]
1 Select "[7] Enter SP Mode" with the DOWN button from the Service Mode screen, and press the [ENTER] button.
2 The SP Mode window menu will be displayed, so select "Start Up" and press the [ENTER] button.
3 The tray will automatically open and the dedicated screen will appear. Place the disc you wish to use on the tray, and push it in manually. ([Close] button will not function)
4 Start Up mode will be initiated, and count will start. Implement 20,000 times (4E20 in hex), and if no errors occur, "Pass" will appear.
If errors do occur, they will be counted. Therefore, errors can be identified without finishing the process.
[ Effective indications ]
Tray sometimes does not open, discs sometimes are not recognized, discs sometime do not playback, (When indications are related to discs, implment on the type of disc which has been pointed out. If it is the disc on which the indications occurred, possibility of reoccurrence is higher.)
1 Select "[7] Enter SP Mode" with the DOWN button from the Service Mode screen, and press the [ENTER] button.
2 The SP Mode window menu will be displayed, so select "Start Up" and press the [ENTER] button.
3 The tray will automatically open and the dedicated screen will appear. Place the disc you wish to use on the tray, and push it in manually. ([Close] button will not function)
4 Start Up mode will be initiated, and count will start. Implement 20,000 times (4E20 in hex), and if no errors occur, "Pass" will appear.
If errors do occur, they will be counted. Therefore, errors can be identified without finishing the process.
[ Effective indications ]
Tray sometimes does not open, discs sometimes are not recognized, discs sometime do not playback, (When indications are related to discs, implment on the type of disc which has been pointed out. If it is the disc on which the indications occurred, possibility of reoccurrence is higher.)
Jitter Measure / BLER Measure
[ Content of
test ]
Measures the Jitter or the Block Error Rate (BLER) of the disc inserted.
Only Pass or NG will be displayed, not Measurement values.
All of CD, DVD, and BD can be judged.
[ Instructions ]
1 Select "[7] Enter SP Mode" with the DOWN button from the Service Mode screen, and press the [ENTER] button.
2 The SP Mode window menu will be displayed, so select either "Jitter Measure" "BLER Measure," and press the [ENTER] button.
3 The tray will automatically open and the dedicated screen will appear. Place the disc you wish to use on the tray, and push it in manually. ([Close] button will not function)
4 The tray will reopen automatically. Measurement will start when you push the tray in manually.
5 When test is completed, "Pass" or "NG" is displayed.
[ Effective indications ]
Defect related to playback (blocked noise, sound jumping, image jumping, disc is paused, freeze of screen etc.) If an NG is generated in a specific disc only, the defect is likely to be caused by the disc. If an NG is generated in other discs too, the defect is likely to be caused by the drive part. However, even if Pass is displayed after this test, it is difficult to determine that the Driver is normal with these Pass judgments only.
Measures the Jitter or the Block Error Rate (BLER) of the disc inserted.
Only Pass or NG will be displayed, not Measurement values.
All of CD, DVD, and BD can be judged.
[ Instructions ]
1 Select "[7] Enter SP Mode" with the DOWN button from the Service Mode screen, and press the [ENTER] button.
2 The SP Mode window menu will be displayed, so select either "Jitter Measure" "BLER Measure," and press the [ENTER] button.
3 The tray will automatically open and the dedicated screen will appear. Place the disc you wish to use on the tray, and push it in manually. ([Close] button will not function)
4 The tray will reopen automatically. Measurement will start when you push the tray in manually.
5 When test is completed, "Pass" or "NG" is displayed.
[ Effective indications ]
Defect related to playback (blocked noise, sound jumping, image jumping, disc is paused, freeze of screen etc.) If an NG is generated in a specific disc only, the defect is likely to be caused by the disc. If an NG is generated in other discs too, the defect is likely to be caused by the drive part. However, even if Pass is displayed after this test, it is difficult to determine that the Driver is normal with these Pass judgments only.
Error List
The following
serves as the Error List generated in SP MODE
|
Error
Code
|
Error
Name
|
Description
|
|
12
|
PWR_CURVE_ERROR
|
Power curve chk-sum error
|
|
22
|
STARTUP_TIMEOUT_ERROR
|
Time-out criterion over
|
|
23
|
MEDIA_MISMATCH
|
Wrong disc
|
|
25
|
DISCID_ERROR 0x25
|
Disc ID error
|
|
26
|
MEDIUM_SUPPORT_ERROR
|
Unsupported disc
|
|
31
|
TRAYOUT_ERROR
|
Tray-out time-out criterion over
|
|
32
|
TRAYIN_ERROR
|
Tray-in time-out criterion over
|
|
33
|
FLASH_UPDATE_ERROR
|
Updating FA result failed
|
|
36
|
OPU_TEMP_ERROR
|
Abnormal OPU temperature
|
|
41
|
SEEK_TIMEOUT_ERROR
|
Seek time-out criterion over
|
|
42
|
SEEK_CMD_FAIL_ERROR
|
Seek command failed
|
|
51
|
READ_TOC_ERROR
|
Read TOC command failed
|
|
52
|
TOC_TIMEOUT_ERROR
|
TOC read time-out criterion over
|
|
61
|
PIPO_TIMEOUT_ERROR
|
Time-out criterion over
|
|
62
|
PIPO_C1C2_ERROR
|
Read PIPO command failed
|
|
63
|
PIPO_C1C2_OVER
|
PIPO criterion over
|
|
71
|
RD_CMD_FAIL_ERROR
|
Read command failed
|
|
72
|
RD_CMD_ERROR
|
Command error or illegality mode
|
|
73
|
RD_TIME_OUT_ERROR
|
Read command time-out criterion over
|
|
81
|
CHECK_FA_TABLE_ERROR
|
FA table check-sum error
|
UPDATING
OF THE FIRMWARE
The following are the steps of update:
1. Before update, please check the current version of firmtware installed in this unit.
You can press [HOME MENU] button to enter the menu, after that, press UP/DOWN/LEFT/RIGHT buttons to display
"Home Menu" > "Initial Setup" > "Options" > "System Information" > "Next Screen", then you can see the information of current firmware version by pressing the [ENTER] button.
2. Save the updating file [DLdiscidentifier.txt], [DVD.bin] and [BDP-3130_Vxx.xx.bin] to the USB memory device route path.
3. After step 2, please insert the USB memory device into unit. While the screen shows the information that a USB memory device has been inserted, please press [HOME MENU] button to enter the menu, then find "USB devices" through "Home Menu" > "Initial Setup" > "Options" > "Update" > "USB Storage" After press the [ENTER] button, the system will search the update file itself to update.
4. After reset, the unit is available for test.
1. Before update, please check the current version of firmtware installed in this unit.
You can press [HOME MENU] button to enter the menu, after that, press UP/DOWN/LEFT/RIGHT buttons to display
"Home Menu" > "Initial Setup" > "Options" > "System Information" > "Next Screen", then you can see the information of current firmware version by pressing the [ENTER] button.
2. Save the updating file [DLdiscidentifier.txt], [DVD.bin] and [BDP-3130_Vxx.xx.bin] to the USB memory device route path.
3. After step 2, please insert the USB memory device into unit. While the screen shows the information that a USB memory device has been inserted, please press [HOME MENU] button to enter the menu, then find "USB devices" through "Home Menu" > "Initial Setup" > "Options" > "Update" > "USB Storage" After press the [ENTER] button, the system will search the update file itself to update.
4. After reset, the unit is available for test.
