PIONEER BDP-LX54 - BDP-43FD - BDP-430 - BDP-41FD BLU RAY PLAYER
FACTORY RESET SOFTWARE UPDATE TROUBLE SHOOTING AND POWER SUPPLY CIRCUIT
To Reset this Player
# If this Player receives strong interference from a source such as excessive static electricity, strong external noise, malfunction of power supply, or voltage caused by lightning during use or a wrong operation is sent to the Player, errors like the Player not accepting an operation may occur. Press and hold STANDBY/ON on the Player until "RESET" appears on the front panel display when the Player does not operate properly even after the power has been turned off. Then turn on the power again.
# It may take several minutes until completion as the system check will be executed when the power is turned ON. Please wait until the indicator lights up in this case.
# Since all settings including the language setting stored in memory are also reset when a reset has been performed, they must be set again.
# When the problem persists even after performing a reset, unplug the AC cord and plug it in again. If this does not solve the problem, contact the nearest service center approved by Pioneer.
# If this Player receives strong interference from a source such as excessive static electricity, strong external noise, malfunction of power supply, or voltage caused by lightning during use or a wrong operation is sent to the Player, errors like the Player not accepting an operation may occur. Press and hold STANDBY/ON on the Player until "RESET" appears on the front panel display when the Player does not operate properly even after the power has been turned off. Then turn on the power again.
# It may take several minutes until completion as the system check will be executed when the power is turned ON. Please wait until the indicator lights up in this case.
# Since all settings including the language setting stored in memory are also reset when a reset has been performed, they must be set again.
# When the problem persists even after performing a reset, unplug the AC cord and plug it in again. If this does not solve the problem, contact the nearest service center approved by Pioneer.
FACTORY REST
To reset to
factory default, proceed as follows:
1. Select "SHIP" then "ON" on the menu, using the [UP/DOWN/LEFT/RIGHT] key on the supplied remote control unit, then press the ENTER key.
2. The unit automatically turns off and on. The On Screen Language setting screen is displayed,Select the language.
1. Select "SHIP" then "ON" on the menu, using the [UP/DOWN/LEFT/RIGHT] key on the supplied remote control unit, then press the ENTER key.
2. The unit automatically turns off and on. The On Screen Language setting screen is displayed,Select the language.
UPDATING OF THE FIRMWARE
Updating Procedure
Note: Be sure to update the firmware after the MAIN PWB-S is replaced.
(Updating can also be performed using the User menu. For details, refer to the operating instructions of the unit.)
1. Press [STANDBY/ON] button to turn the switch on, then wait till the BD/DVD/CD disc indicator changes from blinking to lit.
2. Press [OPEN/CLOSE] button to open the Tray, put the update disc on the tray and close the tray.
3. The updating with the disc will start.
4. During the updating, "NOW UPDATING DO NOT UNPLUG AC CORD" appears on the monitor screen. And the version updating progress bar is displayed.
5. When updating with the disc is completed, the Tray automatically opens.
6. When the updating is completed, the following appears on the monitor screen. : "Success, Please remove the disc..."
If the version updating fails, take out the disc, turn off the power and take the procedure again starting from [1] above.
7. Remove the disc from the Tray and press [ENTER], then the Tray will close and the power will automatically turn off and on.
# If the front-end software was updated, start updating front-end software at this point. Please follow the procedure described on the screen.
8. Check the version on [HOME MENU] - [SETTINGS] - [VERSION]. If the version is not updated, take the procedure again from Step [2].
Note: Be sure to update the firmware after the MAIN PWB-S is replaced.
(Updating can also be performed using the User menu. For details, refer to the operating instructions of the unit.)
1. Press [STANDBY/ON] button to turn the switch on, then wait till the BD/DVD/CD disc indicator changes from blinking to lit.
2. Press [OPEN/CLOSE] button to open the Tray, put the update disc on the tray and close the tray.
3. The updating with the disc will start.
4. During the updating, "NOW UPDATING DO NOT UNPLUG AC CORD" appears on the monitor screen. And the version updating progress bar is displayed.
5. When updating with the disc is completed, the Tray automatically opens.
6. When the updating is completed, the following appears on the monitor screen. : "Success, Please remove the disc..."
If the version updating fails, take out the disc, turn off the power and take the procedure again starting from [1] above.
7. Remove the disc from the Tray and press [ENTER], then the Tray will close and the power will automatically turn off and on.
# If the front-end software was updated, start updating front-end software at this point. Please follow the procedure described on the screen.
8. Check the version on [HOME MENU] - [SETTINGS] - [VERSION]. If the version is not updated, take the procedure again from Step [2].
Note: Do not unplug the AC cord during
version updating.
TROUBLE SHOOTING
Power does not come ON.
Is the 12V
power supplied to pins (2, 3 and 4) of P9001 inside MAIN PWB-S (AT_12V) while
AC is ON and the power source is OFF >>The POWER Assy is normal. (12V
power is supplied.) Replace and check MAIN PWB-S.
Disconnect the
P9001 connector on the MAIN PWB-S after turn the power off, then do not pins 2
and 5 of P9001 on the MAIN PWB-S short-circuit >>Replace and check the MAIN PWB-S.
(Short-circuit is being caused in the MAIN PWB-S.).
Is the 12V
power supplied to pins (2, 3 and 4) of CN901 on the POWER Assy (AT_12V) while
AC is ON and the power source is OFF >>Replace and check the POWER Assy. (The circuit up to
12 V generation in the POWER Assy has broken down.).
Check between
CN901 on the POWER Assy and P9001 on the MAIN PWB-S and their peripheral
circuits. (e.g. nearly detached connector, disconnection).
BD drive does not operate properly.
Does the
problem (discs cannot be played back stably) happen only to certain discs
>>
(In case discs
cause the problem)
1 Check any dirt on discs.
2 Check whether the problem is disc-specific.
1 Check any dirt on discs.
2 Check whether the problem is disc-specific.
Does the
problem happen only to BD, DVD or CD >>(In case LD breakdown etc. causes the problem) Replace
and check BD drive.
Is the error
rate wrong >>
(In case the
problem derives from PU breakdown or disc-related factors)
1 Check any dirt on discs
2 Check whether the problem is disc-specific (e.g. Pirated edition)
3 Replace and check BD drive
1 Check any dirt on discs
2 Check whether the problem is disc-specific (e.g. Pirated edition)
3 Replace and check BD drive
1 Check the drive relay board (BRIDGE Assy) and circuits around
CN101 and CN104. Check any connector nearly detached or obliquely inserted. Check
any disconnected pattern etc.
2 Replace and check MAIN PWB-S.
3 Replace and check BD drive.
2 Replace and check MAIN PWB-S.
3 Replace and check BD drive.
Discs cannot be played back stably.
Does SLED motor
initialize while the power is ON >>
1 Check the drive relay board (BRIDGE Assy) and circuits around
CN101 and CN104.
Check any connector nearly detached or obliquely inserted.
Check any disconnected pattern etc.
2 Replace and check MAIN PWB-S.
3 Replace and check BD drive.
Check any connector nearly detached or obliquely inserted.
Check any disconnected pattern etc.
2 Replace and check MAIN PWB-S.
3 Replace and check BD drive.
Does it load
>>
1 Check the drive relay board (BRIDGE Assy) and circuits around
CN102 and CN104.
Check any connector nearly detached or obliquely inserted.
Check any disconnected pattern etc.
2 Replace and check MAIN PWB-S.
3 Replace and check BD drive.
Check any connector nearly detached or obliquely inserted.
Check any disconnected pattern etc.
2 Replace and check MAIN PWB-S.
3 Replace and check BD drive.
Does the
spindle revolve when a disc is inserted.
1 Check the drive relay board (BRIDGE Assy) and circuits around
CN103 and CN104.
Check any connector nearly detached or obliquely inserted.
Check any disconnected pattern etc.
2 Replace and check MAIN PWB-S.
3 Replace and check BD drive.
Check any connector nearly detached or obliquely inserted.
Check any disconnected pattern etc.
2 Replace and check MAIN PWB-S.
3 Replace and check BD drive.
How to open the tray when the
power cannot be turned on
When the tray
cannot be opened because the power cannot be turned on, it can be opened using the
emergency disc ejection rod (GGF1529). (A long, thin rod about 1 mm in diameter
can be used in place of the rod.) Bend the emergency disc ejection rod at
aright angle, and insert it horizontally into a hole as shown in the figure.
POWER SUPPLY CIRCUIT
CLICK ON THE IMAGES TO ZOOM IN
