SANYO BLU RAY
|
SANYO LCD-24K40
SERVICE MODE POWER SUPPLY CIRCUIT AND INVERTER CIRCUIT
On-screen Service Menu
General
This set has an On-screen Service Menu System included in the CPU that allows remote operation for most of the service adjustments.
Service Menu
Quick operation is needed to enter Service Mode.
How to enter the Service Menu
1. Press and hold the MENU button on Side Controls.
2. Keep pressing the MENU button and press the "1" button on the remote control, and the FACTORY MENU will be displayed.
This set has an On-screen Service Menu System included in the CPU that allows remote operation for most of the service adjustments.
Service Menu
Quick operation is needed to enter Service Mode.
How to enter the Service Menu
1. Press and hold the MENU button on Side Controls.
2. Keep pressing the MENU button and press the "1" button on the remote control, and the FACTORY MENU will be displayed.
To adjust data:
1) Select “DATA” line by pressing ▲▼ button
1) Select “DATA” line by pressing ▲▼ button
2) Press ◄► button to adjust data.
To exit service mode
Press MENU button to exit service mode.
Note: The all adjusted data in service mode will be memorized into EEPROM automatically.
Press MENU button to exit service mode.
Note: The all adjusted data in service mode will be memorized into EEPROM automatically.
Setting the Initial data
This adjustment is controlled by the CPU (IC8000) through the IIC Bus Data Line in the chassis, and those adjustment data are memorized the memory IC (IC7200). Therefore, Main board or the memory IC (IC7200) is replaced, these data will be disappeared. Readjust should be made. Initial data is provided in the CPU ROM, when the memory IC (IC7200) is replaced with new one. CPU ROM data is loaded into the memory.
This adjustment is controlled by the CPU (IC8000) through the IIC Bus Data Line in the chassis, and those adjustment data are memorized the memory IC (IC7200). Therefore, Main board or the memory IC (IC7200) is replaced, these data will be disappeared. Readjust should be made. Initial data is provided in the CPU ROM, when the memory IC (IC7200) is replaced with new one. CPU ROM data is loaded into the memory.
Initial data is provided to operating the monitor basically. For operating the
monitor quality performance, further adjustment is required following chassis electrical adjustment.
1. Receive good quality signal.
2. Enter the Service Mode.
3. Confirm data value to be the same as the Service Adjustment Data Table. If it is different, change to
correct data
4. Exit the Service Mode
2. Enter the Service Mode.
3. Confirm data value to be the same as the Service Adjustment Data Table. If it is different, change to
correct data
4. Exit the Service Mode
White and Black Balance Adjustment
Pattern
White Pattern 100% (in AV mode).
Condition
Picture Mode: STANDARD
Color Temperature: NORMAL
Pre-heating Time: More than 10 minutes
Adjustment
1. Enter the Service Mode.
2. Select WHITE BALANCE / BLACK BALANCE by pressing ▲▼ button, and press ◄► button to enter.
3. Set R,G,B value to “FF” by pressing NUMERIC buttons.
To adjust Red : Press 1 (data value up) and 4 (data value down).
To adjust Green : Press 2 (data value up) and 5 (data value down).
To adjust Blue : Press 3 (data value up) and 6 (data value down)
Pattern
White Pattern 100% (in AV mode).
Condition
Picture Mode: STANDARD
Color Temperature: NORMAL
Pre-heating Time: More than 10 minutes
Adjustment
1. Enter the Service Mode.
2. Select WHITE BALANCE / BLACK BALANCE by pressing ▲▼ button, and press ◄► button to enter.
3. Set R,G,B value to “FF” by pressing NUMERIC buttons.
To adjust Red : Press 1 (data value up) and 4 (data value down).
To adjust Green : Press 2 (data value up) and 5 (data value down).
To adjust Blue : Press 3 (data value up) and 6 (data value down)
4. Decide one item in three items to a fixed value (For example,
let R be fixed value), select item of other
2 colors (Example, G or B), and adjust to produce a normal black and white picture in highlight areas.
(Note: At this time, Adjust the other colors data less than fixed data.)
2 colors (Example, G or B), and adjust to produce a normal black and white picture in highlight areas.
(Note: At this time, Adjust the other colors data less than fixed data.)
5. Exit the Service Mode.
After adjustment, confirm white balance again by normal picture.
After adjustment, confirm white balance again by normal picture.
POWER SUPPLY CIRCUIT
INVERTER CIRCUIT
CLICK ON THE IMAGES TO ZOOM IN
