SHARP BLU RAY
|
SHARP LC-32LE210E/RU - LC-32LE210EB/RUB - LC-32LE220E/RU - LC-32LE220EB/RUB - LC-32LB220E/RU - LC-32LB220EB/RUB - LC-32LS220E/RU - LC-32LS220EB/RUB
LED LCD
SERVICE MODE AND POWER SUPPLY CIRCUIT
Entering and exiting the adjustment process mode.
Standard method.
1. By key-unit.
1. Unplug the AC power cord.
2. Press and hold “V-” and “AV (INPUT ) ” keys, simultaneously, and then plug the AC power cord.
3. “K” appears on the screen.
4. Press and hold “V-” and “P-” keys, simultaneously.
5. “SHARP FACTORY MENU” appears .
6. Unplug the AC power cord to exit of adjustments process.
2. By own R/C
1. Turn on the TV set.
2. Press “AV(INPUT)”,”2”,”5”, “8”, “0” (the time is limited to 5 sec. approx., for enter this code).
3. “SHARP FACTORY MENU” appears.
4. Press “OK” on lines 5 >12 to go to submenu.
5. Press “MENU” to return to main menu.
6. Press “END” to exit of adjustments mode.
1. By key-unit.
1. Unplug the AC power cord.
2. Press and hold “V-” and “AV (INPUT ) ” keys, simultaneously, and then plug the AC power cord.
3. “K” appears on the screen.
4. Press and hold “V-” and “P-” keys, simultaneously.
5. “SHARP FACTORY MENU” appears .
6. Unplug the AC power cord to exit of adjustments process.
2. By own R/C
1. Turn on the TV set.
2. Press “AV(INPUT)”,”2”,”5”, “8”, “0” (the time is limited to 5 sec. approx., for enter this code).
3. “SHARP FACTORY MENU” appears.
4. Press “OK” on lines 5 >12 to go to submenu.
5. Press “MENU” to return to main menu.
6. Press “END” to exit of adjustments mode.
RGB SCART ADC
1. Enter in Service mode.
2. Press “DOWN” until selecting “ADC ADJUST” option.
3. Press “OK”.
4. “ADC ADJUST” menu appears.
5. Press “DOWN” until selecting “ADJUST” option.
6. Press “RIGHT”until selecting “Internal Signal”.
7. Press “UP”until selecting “MODE” option.
8. Press “RIGHT”until selecting “RGB”.
9. Press “DOWN” until selecting “AUTO ADC” option.
10. Press “RIGHT”, the adjustment starts.
11. “SUCCESS” appears when the adjustments Finish.
12. Exit of Service mode.
1. Enter in Service mode.
2. Press “DOWN” until selecting “ADC ADJUST” option.
3. Press “OK”.
4. “ADC ADJUST” menu appears.
5. Press “DOWN” until selecting “ADJUST” option.
6. Press “RIGHT”until selecting “Internal Signal”.
7. Press “UP”until selecting “MODE” option.
8. Press “RIGHT”until selecting “RGB”.
9. Press “DOWN” until selecting “AUTO ADC” option.
10. Press “RIGHT”, the adjustment starts.
11. “SUCCESS” appears when the adjustments Finish.
12. Exit of Service mode.
COMPONENTS ADC
1. Enter in Service mode.
2. Press “DOWN” until selecting “ADC ADJUST” option.
3. Press “OK”.
4. “ADC ADJUST” menu appears.
5. Press “DOWN” until selecting “ADJUST” option.
6. Press “RIGHT”until selecting “Internal Signal”.
7. Press “UP”until selecting “MODE” option.
8. Press “RIGHT”until selecting “YPbPr(SD)” or “YPbPr(HD)”
9. Press “DOWN” until selecting “AUTO ADC” option.
10. Press “RIGHT”, the adjustment starts.
11. “SUCCESS” appears when the adjustments Finish.
Note: both SD and HD are adjusted.
12. Exit of Service mode.
1. Enter in Service mode.
2. Press “DOWN” until selecting “ADC ADJUST” option.
3. Press “OK”.
4. “ADC ADJUST” menu appears.
5. Press “DOWN” until selecting “ADJUST” option.
6. Press “RIGHT”until selecting “Internal Signal”.
7. Press “UP”until selecting “MODE” option.
8. Press “RIGHT”until selecting “YPbPr(SD)” or “YPbPr(HD)”
9. Press “DOWN” until selecting “AUTO ADC” option.
10. Press “RIGHT”, the adjustment starts.
11. “SUCCESS” appears when the adjustments Finish.
Note: both SD and HD are adjusted.
12. Exit of Service mode.
PC IN RGB ADC
1. Enter in Service mode.
2. Press “DOWN” until selecting “ADC ADJUST” option.
3. Press “OK”.
4. “ADC ADJUST” menu appears.
5. Press “DOWN” until selecting “ADJUST” option.
6. Press “RIGHT”until selecting “Internal Signal”.
7. Press “Ÿ”until selecting “MODE” option.
8. Press “RIGHT”until selecting “PC-RGB”.
9. Press “DOWN” until selecting “AUTO ADC” option.
10. Press “RIGHT”, the adjustment starts
11. “SUCCESS” appears when the adjustments Finish.
12. Exit of Service mode
1. Enter in Service mode.
2. Press “DOWN” until selecting “ADC ADJUST” option.
3. Press “OK”.
4. “ADC ADJUST” menu appears.
5. Press “DOWN” until selecting “ADJUST” option.
6. Press “RIGHT”until selecting “Internal Signal”.
7. Press “Ÿ”until selecting “MODE” option.
8. Press “RIGHT”until selecting “PC-RGB”.
9. Press “DOWN” until selecting “AUTO ADC” option.
10. Press “RIGHT”, the adjustment starts
11. “SUCCESS” appears when the adjustments Finish.
12. Exit of Service mode
White Balance Adjustment
Condition: AV MODE= Dynamic (backlight at max.).
• Adjustments reference device: Minolta CA-210
• Adjustments target: x=0.272, y=0.277
High: adjustments spec ±0.001, inspection spec: ±0.002
Low: adjustments spec ±0.002, inspection spec: ±0.004
1. Press “DOWN” until selecting “GAMMA” option.
2. Press “OK”.
3. “GAMMA” menu appears.
4. Press “DOWN” until selecting “MGAMMA RESET”.
5. Press “RIGHT”, to restore default values.
6. “MGAMMA RESET SUCCESS” appears.
7. Press “P+” to increase one page.
8. Press “1”, appears “Internal Adjustments Pattern 1”.
9. Hold the default value for “MGAMMA G1”.
(Note: next, try to get the (x, y) adjustments target, changing “MGAMMA R1” and “MGAMMA B1” as follow).
10. Press “DOWN” until selecting “MGAMMA R1”.
11. Press “LEFT/RIGHT” until you obtain the desired value.
12. Press “MENU” to return to previous menu.
13. Press “DOWN” until selecting “MGAMMA B1”.
14. Press “LEFT/RIGHT” until you obtain the desired value.
15. Press “MENU” to return to previous menu.
(Note: In case of not being possible to achieve the desired (x, y) target, try to get it by changing also the “MGAMMA G1”)
16. Press “2”, appears “Internal Adjustments Pattern 2”.
17. Repeat from step 9 to 15 for the “MGAMMA R2” and “MGAMMA B2”.
18. Press “3”, appears “Internal Adjustments Pattern 3”.
19. Repeat from step 9 to 15 for the “MGAMMA R3” and “MGAMMA B3”.
20. Press “4”, appears “Internal Adjustments Pattern 4”.
21. Repeat from step 9 to 15 for the “MGAMMA R4” and “MGAMMA B4”.
22. Press “5”, appears “Internal Adjustments Pattern 5”.
23. Repeat from step 9 to 15 for the “MGAMMA R5” and “MGAMMA B5”.
24. Press “6”, appears “Internal Adjustments Pattern 6”.
25. Repeat from step 9 to 15 for the “MGAMMA R6” and “MGAMMA B6”.
26. Press “DOWN” until selecting “MGAMMA WRITE”.
27. Press “RIGHT ”, to save the new values.
28. “MGAMMA WRITE SUCCESS” appears.
NOTE: For activating the W/B flag, only is necessary to send the order MGAMMA WRITE. After this action, the “W” W/B flag will change to “1”.
Condition: AV MODE= Dynamic (backlight at max.).
• Adjustments reference device: Minolta CA-210
• Adjustments target: x=0.272, y=0.277
High: adjustments spec ±0.001, inspection spec: ±0.002
Low: adjustments spec ±0.002, inspection spec: ±0.004
1. Press “DOWN” until selecting “GAMMA” option.
2. Press “OK”.
3. “GAMMA” menu appears.
4. Press “DOWN” until selecting “MGAMMA RESET”.
5. Press “RIGHT”, to restore default values.
6. “MGAMMA RESET SUCCESS” appears.
7. Press “P+” to increase one page.
8. Press “1”, appears “Internal Adjustments Pattern 1”.
9. Hold the default value for “MGAMMA G1”.
(Note: next, try to get the (x, y) adjustments target, changing “MGAMMA R1” and “MGAMMA B1” as follow).
10. Press “DOWN” until selecting “MGAMMA R1”.
11. Press “LEFT/RIGHT” until you obtain the desired value.
12. Press “MENU” to return to previous menu.
13. Press “DOWN” until selecting “MGAMMA B1”.
14. Press “LEFT/RIGHT” until you obtain the desired value.
15. Press “MENU” to return to previous menu.
(Note: In case of not being possible to achieve the desired (x, y) target, try to get it by changing also the “MGAMMA G1”)
16. Press “2”, appears “Internal Adjustments Pattern 2”.
17. Repeat from step 9 to 15 for the “MGAMMA R2” and “MGAMMA B2”.
18. Press “3”, appears “Internal Adjustments Pattern 3”.
19. Repeat from step 9 to 15 for the “MGAMMA R3” and “MGAMMA B3”.
20. Press “4”, appears “Internal Adjustments Pattern 4”.
21. Repeat from step 9 to 15 for the “MGAMMA R4” and “MGAMMA B4”.
22. Press “5”, appears “Internal Adjustments Pattern 5”.
23. Repeat from step 9 to 15 for the “MGAMMA R5” and “MGAMMA B5”.
24. Press “6”, appears “Internal Adjustments Pattern 6”.
25. Repeat from step 9 to 15 for the “MGAMMA R6” and “MGAMMA B6”.
26. Press “DOWN” until selecting “MGAMMA WRITE”.
27. Press “RIGHT ”, to save the new values.
28. “MGAMMA WRITE SUCCESS” appears.
NOTE: For activating the W/B flag, only is necessary to send the order MGAMMA WRITE. After this action, the “W” W/B flag will change to “1”.
Initialization to factory setting
1. Enter in Service mode.
2. Press “DOWN” or “UP” key until selecting INIT.
3. Press OK key.
4. INIT menu appears and “Factory init” option is selected.
5. Press “LEFT” or “RIGHT” until selecting the option desired (EURO/RUSSIA/SWEDEN/UK/EAST EUROPE).
6. Press OK key and initialization starts.
7. OK, EURO message appears for EURO option when the setting is complete.
OK, RUSSIA message appears for RUSSIA option when the setting is complete.
OK, SWEDEN message appears for SWEDEN option when the setting is complete.
OK, UK message appears for UK option when the setting is complete.
OK, EAST EUROPE message appears for EAST EUROPE option when the setting is complete.
Note: Never turn the power off during initialization.
2. Press “DOWN” or “UP” key until selecting INIT.
3. Press OK key.
4. INIT menu appears and “Factory init” option is selected.
5. Press “LEFT” or “RIGHT” until selecting the option desired (EURO/RUSSIA/SWEDEN/UK/EAST EUROPE).
6. Press OK key and initialization starts.
7. OK, EURO message appears for EURO option when the setting is complete.
OK, RUSSIA message appears for RUSSIA option when the setting is complete.
OK, SWEDEN message appears for SWEDEN option when the setting is complete.
OK, UK message appears for UK option when the setting is complete.
OK, EAST EUROPE message appears for EAST EUROPE option when the setting is complete.
Note: Never turn the power off during initialization.
The following settings will be back to their
factory ones.
• User settings
• Channel data (e.g. broadcast frequencies)
• Maker option setting
• Password data
• User settings
• Channel data (e.g. broadcast frequencies)
• Maker option setting
• Password data
POWER SUPPLY CIRCUIT
Power Supply Diagram LC32LE210/220E MODELS (AUO PANEL)
RDENCA409WJQZ (1 / 2)
Power Supply Diagram LC32LE210/220E MODELS (AUO PANEL)
RDENCA409WJQZ (2 / 2)
Power Supply Diagram LC32LE210/220EB MODELS (CMI PANEL)
RDENCA411WJQZ (1 / 1)
CLICK ON THE IMAGES TO ZOOM IN
