NORDICTRACK X9I INCLINE TRAINER
MOTORISE TREAMILL
FIRMWARE UPDATE AND TROUBLE SHOOTING
UPDATING THE FIRMWARE
For the best results, regularly check for firmware updates.
Touch the Firmware Update button to check for firmware updates using your wireless network. The update will begin automatically.
To avoid damaging the incline trainer, do not turn off the power or remove the key while the firmware is being updated.
Note: Occasionally, a firmware update may cause your console to function slightly differently. These updates are always designed to improve your exercise experience.
Note: If you cannot update the console firmware over your wireless network, you can update the firmware using a USB drive. Go to iFit web page and download the latest firmware update onto your
For the best results, regularly check for firmware updates.
Touch the Firmware Update button to check for firmware updates using your wireless network. The update will begin automatically.
To avoid damaging the incline trainer, do not turn off the power or remove the key while the firmware is being updated.
Note: Occasionally, a firmware update may cause your console to function slightly differently. These updates are always designed to improve your exercise experience.
Note: If you cannot update the console firmware over your wireless network, you can update the firmware using a USB drive. Go to iFit web page and download the latest firmware update onto your
The screen will show the progress of the update. When the update is complete,
the incline trainer will turn off and then turn back on. If it does not, press
the power switch into the off position. Wait for several seconds, and then
press the power switch into the reset position. Note: It may take a few minutes
for the console to be ready for use.
Calibrate the incline system of
the trainer.
Touch the Calibrate Incline button. Then, touch the Begin button to calibrate the incline system. The incline trainer will automatically rise to the maximum incline level, lower to the minimum incline level, and then return to the starting position. This will calibrate the incline system. Press the Cancel button to return to the maintenance mode. When the incline system is calibrated, touch the Finish button.
IMPORTANT: Keep pets, feet, and other objects away from the incline trainer while the incline system is calibrating. In an emergency, pull the key from the console to stop the incline calibration.
Touch the Calibrate Incline button. Then, touch the Begin button to calibrate the incline system. The incline trainer will automatically rise to the maximum incline level, lower to the minimum incline level, and then return to the starting position. This will calibrate the incline system. Press the Cancel button to return to the maintenance mode. When the incline system is calibrated, touch the Finish button.
IMPORTANT: Keep pets, feet, and other objects away from the incline trainer while the incline system is calibrating. In an emergency, pull the key from the console to stop the incline calibration.
TROUBLESHOOTING
TREADMILL IS NOT POWERING UP
a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet Use only a single-outlet surge suppressor that meets all of the specifications of the treadmill
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the power switch located on the incline trainer frame near the power cord. If the switch protrudes as shown, the switch has tripped. To reset the power switch, wait for five minutes and then press the switch back in.
a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet Use only a single-outlet surge suppressor that meets all of the specifications of the treadmill
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the power switch located on the incline trainer frame near the power cord. If the switch protrudes as shown, the switch has tripped. To reset the power switch, wait for five minutes and then press the switch back in.
TREADMILL POWER FAILS WHILE
WORKING
a. Check the power switch (see the drawing above). If the switch has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.
a. Check the power switch (see the drawing above). If the switch has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.
c. Remove the
key from the console, and then reinsert it.
d. If the incline trainer still will not run, please see the front cover of this manual.
d. If the incline trainer still will not run, please see the front cover of this manual.
THE DISPLAY WORKS EVEN WHEN KEY IS
NOT IN PLACE
a. The console features a display demo mode, designed to be used if the incline trainer is displayed in a store. If the screen remains lit when you remove the key, the demo mode is turned on.
a. The console features a display demo mode, designed to be used if the incline trainer is displayed in a store. If the screen remains lit when you remove the key, the demo mode is turned on.
NOT DISPLAYING SPEED AND DISTANCE
a. Remove the key from the console and UNPLUG THE POWER CORD. Next, remove the three indicated #8 x 1/2" Cover Screws (18) and the #8 x 1 1/4" Screw (36). Lift off the Left Roller Cover (38).
a. Remove the key from the console and UNPLUG THE POWER CORD. Next, remove the three indicated #8 x 1/2" Cover Screws (18) and the #8 x 1 1/4" Screw (36). Lift off the Left Roller Cover (38).
Locate the Reed
Switch (55) and the Magnet (41) on the left side of the Pulley (42). Turn the
Pulley until the Magnet is aligned with the Reed Switch. Make sure that the
gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If
necessary, loosen the #8 x 3/4" Clamp Screw (20), move the Reed Switch slightly,
and then retighten the Screw. Reattach the Left Roller Cover (not shown) and
run the incline trainer for a few minutes to check for a correct speed reading.
INCLINE NOT GOING UP OR DOWN
a. Calibrate the incline system
WAKING BELT SLOWDOWN
a. Use only a single-outlet surge suppressor that meets all of the specifications of the treadmill
a. Calibrate the incline system
WAKING BELT SLOWDOWN
a. Use only a single-outlet surge suppressor that meets all of the specifications of the treadmill
b. If the
walking belt is overtightened, incline trainer performance may decrease and the
walking belt may become damaged. Remove the key and UNPLUG THE POWER CORD. Using
the hex key, turn both idler roller screws counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you should be able to lift each
edge of the walking belt 3 to 4 in. (8 to 10 cm) off the walking platform. Be careful
to keep the walking belt centered. Then, plug in the power cord, insert the key,
and run the incline trainer for a few minutes. Repeat until the walking belt is
properly tightened.
c. Your incline
trainer features a walking belt coated with high-performance lubricant.
IMPORTANT: Never apply silicone spray or
other substances to the walking belt or the walking platform unless
instructed to do so by an authorized service representative. Such substances
may deteriorate the walking belt and cause excessive wear.
CENTRING THE WALKING BELT
a. If the walking belt is off-center, first adjust incline to 40 percent. Remove the key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the hex key to turn the left idler roller screw clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the left idler roller screw counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and run the incline trainer for a few minutes. Repeat until the walking belt is centered.
a. If the walking belt is off-center, first adjust incline to 40 percent. Remove the key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the hex key to turn the left idler roller screw clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the left idler roller screw counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and run the incline trainer for a few minutes. Repeat until the walking belt is centered.
b. If the
walking belt slips when walked on, first adjust incline to 40 percent.
Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both
idler roller screws clockwise, 1/4 of a turn. When the walking belt is
correctly tightened, you should be able to lift each edge of the walking belt 3
to 4 in. (8 to 10 cm) off the walking platform. Be careful to keep the walking
belt centered. Then, plug in the power cord, insert the key, and carefully walk
on the incline trainer for a few minutes. Repeat until the walking belt is
properly tightened.
THE IFIT MODE IS NOT FUNCTIONING
a. If the iFit
Live mode is not functioning correctly, make sure that the incline trainer has
the most current firmware available
NOT CONNECTING TO WIFI NETWORK
a. Make sure that the wireless settings on your console are correct
NOT CONNECTING TO WIFI NETWORK
a. Make sure that the wireless settings on your console are correct
b. Make sure
that the settings for your wireless network are correct.
