PANASONIC DMP-BD45 - DMP-BD65
BLU RAY PLAYER
SERVICE MODE AND POWER SUPPLY CIRCUIT
Taking out the Disc from BD Drive
Unit when the Disc cannot be ejected
by OPEN/CLOSE button .
When the power can be turned off.
1. Turn the unit off, then press and hold [OK], [Yellow] and [Blue] buttons on the remote control simultaneously for 5 seconds.
- “00 RET” is displayed on the unit’s FL display.
2. Repeatedly press the right cursor button on the remote Control or Power button on the unit until “06 FTO” is displayed on the
unit's FL display.
3. Press [OK] button on the remote control or [OPEN/CLOSE] button on the unit.
When the power can not be turned off.
Press [POWER] button on the unit for over 4 seconds to turn off the power forcibly, and step 1 to 3 above.
When the Forcible Disc Eject can not be done.
1. Turn off the power and pull out AC cord.
2. Remove the Top Case.
3. Put the unit so that bottom can be seen.
4. Insert paper clips, etc. into the hole on the bottom of BD Drive and slide the paper clips, etc. in the direction of the arrow to eject tray slightly.
by OPEN/CLOSE button .
When the power can be turned off.
1. Turn the unit off, then press and hold [OK], [Yellow] and [Blue] buttons on the remote control simultaneously for 5 seconds.
- “00 RET” is displayed on the unit’s FL display.
2. Repeatedly press the right cursor button on the remote Control or Power button on the unit until “06 FTO” is displayed on the
unit's FL display.
3. Press [OK] button on the remote control or [OPEN/CLOSE] button on the unit.
When the power can not be turned off.
Press [POWER] button on the unit for over 4 seconds to turn off the power forcibly, and step 1 to 3 above.
When the Forcible Disc Eject can not be done.
1. Turn off the power and pull out AC cord.
2. Remove the Top Case.
3. Put the unit so that bottom can be seen.
4. Insert paper clips, etc. into the hole on the bottom of BD Drive and slide the paper clips, etc. in the direction of the arrow to eject tray slightly.
5. Pull the unit upward, and push out Tray by
paperclips, etc. or minus screw driver (small).
Service Mode
About the Service Mode
Informations necessary for service can be displayed.
How to enter the Service Mode
About the Service Mode
Informations necessary for service can be displayed.
How to enter the Service Mode
Press 5,9 and RED button on the
remote control simultaneously for 5 seconds
Press the right cursor on the remote
or power button on the unit
Press ok button on the remote or
eject button on the unit
Wait 30 second service mode will display
How to exit the Service Mode
Press and hold the [Power] button (remote control or unit).
>>> The Service Mode is terminated and automatically turns the unit off.
Press and hold the [Power] button (remote control or unit).
>>> The Service Mode is terminated and automatically turns the unit off.
How to Clean the Lens of the Optical
Pick-UP
After performing the step “10. 2. 1. Upper Base Ass'y”, clean the lens of the Optical Pick-UP.
After performing the step “10. 2. 1. Upper Base Ass'y”, clean the lens of the Optical Pick-UP.
How to adjust the BDP/Digital P.C.B.
Module
The adjustment may not resume. If interrupt the adjustment, start from the beginning phase.
The adjustment may not resume. If interrupt the adjustment, start from the beginning phase.
Preparation:
Before starting the adjustment, install the adjustment software to PC and copy the SD DIAG software to SD card.
Note:
This adjustment software can be downloaded from “Support Information from NWBG/VDBG-AVC” web-site in “TSN system”,
together with instructions of “BD Drive Adjustment” including preparations and connections etc.
Before starting the adjustment, install the adjustment software to PC and copy the SD DIAG software to SD card.
Note:
This adjustment software can be downloaded from “Support Information from NWBG/VDBG-AVC” web-site in “TSN system”,
together with instructions of “BD Drive Adjustment” including preparations and connections etc.
1. Connect the Serial cable (RFKZ0139) between
serial port connector (P51601) on the Digital P.C.B. and PC's serial port.
# Confirm the PC’s serial port number (COM1, COM2, etc.) connected to serial cable (RFKZ0139), the port number may be set after this procedure.
# Confirm the PC’s serial port number (COM1, COM2, etc.) connected to serial cable (RFKZ0139), the port number may be set after this procedure.
2. Start the Adjustment software, then click the
[Start(S)].
Selection of Model Name
3. Select the model number and click the [OK] button.
# If several other model names might appear, please select the sure model number for the adjustment.
3. Select the model number and click the [OK] button.
# If several other model names might appear, please select the sure model number for the adjustment.
Setting of Adjustment
4. Click the [Utility] button.
4. Click the [Utility] button.
5. Click the [COM Setup] button.
6. Select the COM number that connect the serial
cable (RFKZ0139) and click the [OK] button.
7. Click the [Exit] button.
8. Click the [Adjustment] button.
The Diag Adjustment (SD Diag)
start
9. When below message displayed, perform followings:
a. Insert the SD Diag card to SD card slot.
b. Set the RFKZ0139 SW into “ON”.
c. Click the [OK] button.
9. When below message displayed, perform followings:
a. Insert the SD Diag card to SD card slot.
b. Set the RFKZ0139 SW into “ON”.
c. Click the [OK] button.
10. When below message displayed, perform
followings:
a. Connect the power cable to the unit.
b. Press the [POWER] button of the unit.
c. Click the [OK] button.
a. Connect the power cable to the unit.
b. Press the [POWER] button of the unit.
c. Click the [OK] button.
# If the BD Drive has replaced before, the
following replaced date message is displayed, click the [OK] button for closing
the window.
11. The unit is turned on, then “DIAG” is
displayed at FL dis
play and automatically begins adjustment.
12. When below message displayed, perform followings:
a. Remove the SD Diag card from the SD card slot.
b. Disconnect the power cable from the unit.
c. Click the [OK] button.
play and automatically begins adjustment.
12. When below message displayed, perform followings:
a. Remove the SD Diag card from the SD card slot.
b. Disconnect the power cable from the unit.
c. Click the [OK] button.
LPC Adjustment
13. When below message displayed, perform followings:
a. Set the RFKZ0139 SW into “OFF”.
b. Connect the power cable to the unit.
c. Click the [OK] button.
13. When below message displayed, perform followings:
a. Set the RFKZ0139 SW into “OFF”.
b. Connect the power cable to the unit.
c. Click the [OK] button.
14. The unit is automatically turned on. After a
while the FL display displays “TEST” and automatically begins adjustment.
When the adjustment is completed, the display is
changed to “ADJ1OK”.
DVD-RAM Adjustment
15. The disc tray is automatically opened and the following message is displayed, set the DVD-RAM test disc (X5RAM-BPS) on the tray and click the [OK] button.
When the adjustment is completed, the display is
changed to “ADJ1OK”.
DVD-RAM Adjustment
15. The disc tray is automatically opened and the following message is displayed, set the DVD-RAM test disc (X5RAM-BPS) on the tray and click the [OK] button.
When clicking the [OK] button, the tray is
automatically closed. After a while the FL display displays “ADJ2” and automatically
begins adjustment. When the adjustment is completed, the display is changed to
“ADJ2OK”.
Caution:
Do not press the [OPEN/CLOSE] button of the unit.
16. The disc tray is automatically opened and the following message is displayed, remove the DVD-RAM test disc (X5RAM-BPS) on the tray and click the [OK] button.
Caution:
Do not press the [OPEN/CLOSE] button of the unit.
16. The disc tray is automatically opened and the following message is displayed, remove the DVD-RAM test disc (X5RAM-BPS) on the tray and click the [OK] button.
BD-ROM Adjustment
17. When the following message is displayed, set the BD ROM test disc (VFF0396) on the tray, then click the [OK] button.
17. When the following message is displayed, set the BD ROM test disc (VFF0396) on the tray, then click the [OK] button.
When clicking the [OK] button, the tray is
automatically closed. After a while the FL display displays “ADJ3” and automatically
begins adjustment. When the adjustment is completed, the display is changed to
”ADJ3OK”.
Caution:
Do not press the [OPEN/CLOSE] button of the unit.
18. The disc tray is automatically opened and the following message is displayed, remove the BD-ROM test disc (VFF0396) on the tray and click the [OK] button.
Caution:
Do not press the [OPEN/CLOSE] button of the unit.
18. The disc tray is automatically opened and the following message is displayed, remove the BD-ROM test disc (VFF0396) on the tray and click the [OK] button.
CD-ROM Adjustment
19. When the following message is displayed, set the CD ROM test disc (CD-ROM-B01) on the tray, then click the [OK] button.
19. When the following message is displayed, set the CD ROM test disc (CD-ROM-B01) on the tray, then click the [OK] button.
When clicking the [OK] button, the tray is
automatically closed.
The FL display displays “TEST” and after a while the dis play changes to “CDDA” and adjustment is automatically begun. When the adjustment is completed, the display is changed to “TEST”.
Caution:
Do not press the [OPEN/CLOSE] button of the unit.
20. The disc tray is automatically opened and the following message is displayed, remove the CD-ROM test disc (CD-ROM-B01) on the tray and click the [OK] button.
The FL display displays “TEST” and after a while the dis play changes to “CDDA” and adjustment is automatically begun. When the adjustment is completed, the display is changed to “TEST”.
Caution:
Do not press the [OPEN/CLOSE] button of the unit.
20. The disc tray is automatically opened and the following message is displayed, remove the CD-ROM test disc (CD-ROM-B01) on the tray and click the [OK] button.
When clicking the [OK] button, the tray is
automatically closed. The FL display displays “FACT” and after a while the
display changes to “FACTOK” and re-changed to “P OFF”.
Finishing the Drive Adjustment
21. When below message displayed, perform followings:
a. Confirm “P OFF” is displayed at the FL Display.
b. Disconnect the power cord from the unit.
c. Click the [OK] button.
21. When below message displayed, perform followings:
a. Confirm “P OFF” is displayed at the FL Display.
b. Disconnect the power cord from the unit.
c. Click the [OK] button.
22. Click the [Exit] button.
23. Click the [Exit] button.
24. Click the [Exit(E)] button.
The Drive Adjustment is finished.
When the latest data is updated to TSN
The data file of the adjustment software may be update because of a firmware update of the machine or other reason. In such case, perform the following steps and use the latest data.
1. Download the latest data to PC.
2. Click the “Spec Setup” button before the step 7.
The data file of the adjustment software may be update because of a firmware update of the machine or other reason. In such case, perform the following steps and use the latest data.
1. Download the latest data to PC.
2. Click the “Spec Setup” button before the step 7.
3. Open the downloaded data and click the “New”
button. Then retrieve the data.
4. Select the latest data and click the “OK”
button.
5. Go back the step 7 and click the “Exit”
button.
POWER SUPPLY CIRCUIT
CLICK ON THE IMAGE TO ZOOM IN
