PANASONIC TX-32LX700F - TX-32LX700P
SERVICE MODE AND LED BLINKING CODE
Power LED blinking
timing chart
When abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the defective block can be identified by number of blinking of the Power LED on the front panel of the unit.
When abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the defective block can be identified by number of blinking of the Power LED on the front panel of the unit.
Blinking times
|
Contents
|
Check point
|
1
|
INVERTER_SOS
|
DG BOARD
LCD PANEL |
2
|
FAN_SOS
|
H BOARD
DG BOARD |
3
|
BT_30V,SOUND 15V
PANEL 12V, HQ_ 3.3V |
H BOARD
AP BOARD,DG BOARD |
4
|
DTV_9V
|
AP BOARD
H BOARD, DG BOARD |
5
|
MAIN_9V
|
AP BOARD
H BOARD, DG BOARD |
6
|
SUB_5V
|
AP BOARD
H BOARD, DG BOARD |
7
|
MAIN_5V
|
DG BOARD
|
8
|
MAIN_3.3V
|
DG BOARD
|
9
|
SOUND_SOS
|
H BOARD
DG BOARD |
10
|
HQ1L_SOS
|
DG BOARD
|
Service Mode Function
MPU controls the functions switching for each IICs through IIC bus in this chassis. The following setting and adjustment can
be adjusted by remote control in Service Menu
How to enter SERVICE
While pressing (-/v) button on the TV unit, press 0 on the remote control for 3 times within 2 seconds.
Note:
To exit from Service mode, press the exit button on remote control.
MPU controls the functions switching for each IICs through IIC bus in this chassis. The following setting and adjustment can
be adjusted by remote control in Service Menu
How to enter SERVICE
While pressing (-/v) button on the TV unit, press 0 on the remote control for 3 times within 2 seconds.
Note:
To exit from Service mode, press the exit button on remote control.
Key Command
# Press the 3/4 button to change the adjustment values or function.
# Press the 1/2 button to step up/down through the functions and adjustments
# Press the numerical button VOLUME (+/-) to change of each option item.
# Press the OK button after each adjustment has been made to store the required values.
# Press the 3/4 button to change the adjustment values or function.
# Press the 1/2 button to step up/down through the functions and adjustments
# Press the numerical button VOLUME (+/-) to change of each option item.
# Press the OK button after each adjustment has been made to store the required values.
Subcontrast
adjustment
1. Receive PAL colour bar (100% white) RF signal.
2. Enter “Contrast” adj. In SERVICE mode.
3. Start adjusting by using Yellow Key.
4. If the adjustment finished normally, the letter of Contrast will change from red
to black.
White Balance adjustment
1. Procedure basically performs checking using the production software and
make automatic adjustment using external computer.
2. It adjusts in the mode of: Colour balance Normal
Viewing Mode Dynamic
1. Receive PAL colour bar (100% white) RF signal.
2. Enter “Contrast” adj. In SERVICE mode.
3. Start adjusting by using Yellow Key.
4. If the adjustment finished normally, the letter of Contrast will change from red
to black.
White Balance adjustment
1. Procedure basically performs checking using the production software and
make automatic adjustment using external computer.
2. It adjusts in the mode of: Colour balance Normal
Viewing Mode Dynamic
BOARD DESCRITION
Board Name
|
Function
|
AP-Board
|
Power Supply Regulator
|
DG-Board
|
Global Core, HDMI, IDTV Processor, D/A Converter
|
G-Board
|
Side AV Connector
|
H-Board
|
AV Connector, TV tuner, AV Switch
|
K-Board
|
Main Switch
|
P-Board
|
Main Input, Power Supply
|
V-Board
|
Remote Receiver, LED IR, Cats
|
GH-Board
|
HDMI
|
GS-Board
|
SD Card
|
Setting
Inspection
Voltage Confirmation
Voltage Confirmation
Confirm
the following voltages:
AP board
Description > Test point > Position > Normal mode > Stand by mode
Sound_Vcc TP7302 AP3, pin 2,3 15V +/- 0,8V Max 5V
DTV_9V TP7502 AP3, pin 17,18 9,1V +/- 0,45V Max 3V
Sub_5V TP7402 AP3, pin 21,22 5,1V +/- 0,25V Max 2V
Main_9V AP3, pin 23 9,1V +/- 0,45V Max 3V
LCD_3.3V TP7602 AP4, pin 16,17 3,3V +/- 0,16V Max 2V
STB_5V TP7103 AP4, pin 3 5,1V +/- 0,25V 5,1V +/- 0,25V
Panel 12V TP7702 AP4, pin 11,12 12,2V +/- 0,6V Max 4V
Description > Test point > Position > Normal mode > Stand by mode
Sound_Vcc TP7302 AP3, pin 2,3 15V +/- 0,8V Max 5V
DTV_9V TP7502 AP3, pin 17,18 9,1V +/- 0,45V Max 3V
Sub_5V TP7402 AP3, pin 21,22 5,1V +/- 0,25V Max 2V
Main_9V AP3, pin 23 9,1V +/- 0,45V Max 3V
LCD_3.3V TP7602 AP4, pin 16,17 3,3V +/- 0,16V Max 2V
STB_5V TP7103 AP4, pin 3 5,1V +/- 0,25V 5,1V +/- 0,25V
Panel 12V TP7702 AP4, pin 11,12 12,2V +/- 0,6V Max 4V
P board
5Vs TP823 P8, pin 1 5,1V +/- 0,25V 5,1V +/- 0,25V
24V TP825 P5, pin 1-3 24V +/- 2V Max 4V
DG board
Sub1,2V TP5601 1,17V - 1,32V
Sub1,8V TP5602 1,7V - 1,9V
Sub3,3V TP5600 3,14V - 3,46V
MHQ1,2V TP4209 1,1V - 1,3V
5Vs TP823 P8, pin 1 5,1V +/- 0,25V 5,1V +/- 0,25V
24V TP825 P5, pin 1-3 24V +/- 2V Max 4V
DG board
Sub1,2V TP5601 1,17V - 1,32V
Sub1,8V TP5602 1,7V - 1,9V
Sub3,3V TP5600 3,14V - 3,46V
MHQ1,2V TP4209 1,1V - 1,3V
