SAMSUNG LE32M86BDX - LE32M87BDX
SERVICE MODE AND ADJUSTMENTS
How to Access Service Mode
Entering Factory Mode
1. To enter "Service Mode" Press the remote -control keys in this sequence :
- If you do not have Factory remote – control
Entering Factory Mode
1. To enter "Service Mode" Press the remote -control keys in this sequence :
- If you do not have Factory remote – control
Power OFF > MUTE > MENU
> MUTE > Power On
- If you have Factory remote – control
- If you have Factory remote – control
PICTURE ON > DISPLAY > FACTORY
The buttons are active in the service mode.
1. Remote - Control Key : Power, Arrow Up, Arrow Down, Arrow Left
Arrow Right, Menu, Enter, Number Key(0~9)
2. Function - Control Key : Power, CH +, CH -, VOL +, VOL -, Menu, TV/VIDEO(Enter)
Panel Check
You have to check Panel Maker Because of different adjustments as follows.
First of all, Check the label rating!
1) Label Rating File
1. Remote - Control Key : Power, Arrow Up, Arrow Down, Arrow Left
Arrow Right, Menu, Enter, Number Key(0~9)
2. Function - Control Key : Power, CH +, CH -, VOL +, VOL -, Menu, TV/VIDEO(Enter)
Panel Check
You have to check Panel Maker Because of different adjustments as follows.
First of all, Check the label rating!
1) Label Rating File
CD PANEL MARK -
A:ACER(AUO) S : SEC C : CMO * If not printed you could consider S(sec) panel mark.
2) If Panel Mark is "A", Set the factory mode indicating as follows.
* Option Byte
1. Inch Option 32"
2. Panel Vender AUO_EXT_N
3. Panel Type 32"AU 100
Others are same shown below
A:ACER(AUO) S : SEC C : CMO * If not printed you could consider S(sec) panel mark.
2) If Panel Mark is "A", Set the factory mode indicating as follows.
* Option Byte
1. Inch Option 32"
2. Panel Vender AUO_EXT_N
3. Panel Type 32"AU 100
Others are same shown below
Service Adjustment
White Balance - Calibration
If picture color is wrong, do calibration first.
Equipment : CA210, Patten : chess pattern
Execute calibration in Factory Mode
Source AV : PAL composite, Component : 1280*720/60Hz
PC : 1024*768/60Hz
White Balance - Calibration
If picture color is wrong, do calibration first.
Equipment : CA210, Patten : chess pattern
Execute calibration in Factory Mode
Source AV : PAL composite, Component : 1280*720/60Hz
PC : 1024*768/60Hz
White Balance - Adjustment
If picture color is wrong, check White Balance condition.
Equipment : CA210, Patten : Flat W/B Pattern
Adjust W/B in Factory Mode
Sub brightness and R/G/B Offset controls low light region
Sub contrast and R/G/B Gain controls high light region
Source AV : PAL composite, Component : 1280*720/60Hz
HDMI[DVI] : 1280*720/60Hz
If picture color is wrong, check White Balance condition.
Equipment : CA210, Patten : Flat W/B Pattern
Adjust W/B in Factory Mode
Sub brightness and R/G/B Offset controls low light region
Sub contrast and R/G/B Gain controls high light region
Source AV : PAL composite, Component : 1280*720/60Hz
HDMI[DVI] : 1280*720/60Hz
Conditions for Measurement
1. On the basis of toshiba ABL pattern : High Light level (57 IRE)
- INPUT SIGNAL GENERATOR : MSPG-925LTH
* Mode NO 2 : 744X484@60 Hz
NO 6 : 1280X720@60 Hz
NO 21 : 1024X768@60 Hz
* Pattern NO 36 : 16 Color Pattern
NO 16 : Toshiba ABL Pattern
2. Optical measuring device : CA210 (FL)
Please use the MSPG-925 LTH generator for model LE26M51B/LE32M51B/LE40M51B/LE46M51B.
Method of Adjustment
1. Adjust the white balance of AV, Component and DVI Modes. (AV Component)
a) Set the input to the mode in which the adjustment will be made (RF DTV PC DVI).
* Input signal - VIDEO Mode : Model #2 (744*484 Mode), Pattern #16
- DTV,DVI Mode : Model #6 (1280*720 Mode), Pattern #16
- HDMI Mode: Model #6(1280*720 Mode), Pattern #16
b) Enter factory color control, confirm the data.
c) Adjust the low light. (Refer to table 1, 2 in adjustment position by mode)
- Adjust sub - Brightness to set the 'Y' value.
- Adjust red offset ('x') and blue offset ('y') to the color coordinates.
1. On the basis of toshiba ABL pattern : High Light level (57 IRE)
- INPUT SIGNAL GENERATOR : MSPG-925LTH
* Mode NO 2 : 744X484@60 Hz
NO 6 : 1280X720@60 Hz
NO 21 : 1024X768@60 Hz
* Pattern NO 36 : 16 Color Pattern
NO 16 : Toshiba ABL Pattern
2. Optical measuring device : CA210 (FL)
Please use the MSPG-925 LTH generator for model LE26M51B/LE32M51B/LE40M51B/LE46M51B.
Method of Adjustment
1. Adjust the white balance of AV, Component and DVI Modes. (AV Component)
a) Set the input to the mode in which the adjustment will be made (RF DTV PC DVI).
* Input signal - VIDEO Mode : Model #2 (744*484 Mode), Pattern #16
- DTV,DVI Mode : Model #6 (1280*720 Mode), Pattern #16
- HDMI Mode: Model #6(1280*720 Mode), Pattern #16
b) Enter factory color control, confirm the data.
c) Adjust the low light. (Refer to table 1, 2 in adjustment position by mode)
- Adjust sub - Brightness to set the 'Y' value.
- Adjust red offset ('x') and blue offset ('y') to the color coordinates.
* Do not adjust green offset data.
d) Adjust the high light. (Refer to table 1, 2 in adjustment position by mode)
- Adjust red gain ('x') and blue gain ('y') to the color coordinates.
* Do not adjust the green gain and sub-contrast (Y) data.
d) Adjust the high light. (Refer to table 1, 2 in adjustment position by mode)
- Adjust red gain ('x') and blue gain ('y') to the color coordinates.
* Do not adjust the green gain and sub-contrast (Y) data.
d) Adjust the high light. (Refer to table 1, 2
in adjustment position by mode)
- Adjust red gain ('x') and blue gain ('y') to the color coordinates.
* Do not adjust the green gain and sub-contrast (Y) data.
- Adjust red gain ('x') and blue gain ('y') to the color coordinates.
* Do not adjust the green gain and sub-contrast (Y) data.
Software Upgrade
How to Update Flash ROM
1. Install the Flash Downloader
ConnectSet(Service Jack)and Jig Cable to execute Program Update.
How to Update Flash ROM
1. Install the Flash Downloader
ConnectSet(Service Jack)and Jig Cable to execute Program Update.
2. Flash Downloader program update
-Before Turning on the set,Click "connect"which is under of OSD Screen!
-Turn on the Set.
-Before Turning on the set,Click "connect"which is under of OSD Screen!
-Turn on the Set.
Troubleshooting
No Power
Does proper DC 13V appear at JP845? > Change
a Assy PCB Power.
Does proper DC A3.3V, A5V appear at C1158,
C1150? > Check a IC1112, Q1103. Change a main PCB ass'y.
Does proper DC 5V, 3.3V, 1.2V appear at C1153,
C1178, C1170? > Check a IC1111, IC1102, IC1113. Change a main PCB ass'y
TIP: How to drive the circuit by force when
LCD panel Lamp is faulty.
- It is available to drive the circuit when the pin of 2 in Main_Power_control CN1101 connect the pin of 4.
- It is available to drive the circuit when the pin of 2 in Main_Power_control CN1101 connect the pin of 4.
No Video (Analog PC)
Check a PC source and check the connection of
DSUB cable? > Input a analog PC signal and connected cable(DPMS).
Does the signal appear at C2078,C2077,C2079(R,
G, B) of IC2001? > PC cable. Change a PC cable. Change a main PCB ass'y.
Does the digital data appear at the output of LVDS
(RA2008~2013)? > Check a IC2001 Change a main PCB ass'y.
Check a LVDS cable? Replace a lcd panel?
No Video (Digital-HDMI)
Does the digital data appear at R1333_UX~R1340_UX?
> Check a a IC1405 Change a main PCB ass'y.
Does the digital data appear at output of
IC4001 LVDS(RA2008~2013)? > Check a IC1405 Change a main PCB ass'y.
Check a LVDS cable? Replace lcd panel.
No Sound
Does the signal appear at Pin #10, #12, #13,
#9 (I2S_CLK, I2S_SCLK, I2S_LRCLK, I2S_DATA) of IC1202? > Check a connection
harness and headphone jack./Side AV Check Sound Processor IC1202 (SGTV5810)
Check the DC 12V of IC1203? > Check a B12V
Line. Change a main PCB ass'y.
Does the signal appear at Pin #47 or 48, #53
or 54(CH1_L Sound) And Pin #36 or 37, #30 or 31 (CH2_R Sound) of IC1203? > Change
a main PCB ass'y.
