SANYO BLU RAY
|
SANYO DP42647
SERVICE MODE AND TROUBLE SHOOTING
This set has an On-screen Service Menu system
included in the CPU that allows remote operation for most of the service
adjustments.
SERVICE MENU SYSTEM
1. Enter the Service Menu:
Turn off the receiver and disconnect the AC power supply.
While pressing the Volume (–) button on the television, reconnect the AC power supply. The Service Menu will now appear. The remote can now be used to make adjustments.
SERVICE MENU SYSTEM
1. Enter the Service Menu:
Turn off the receiver and disconnect the AC power supply.
While pressing the Volume (–) button on the television, reconnect the AC power supply. The Service Menu will now appear. The remote can now be used to make adjustments.
2. Service Adjustments:
Press the Channel UP or DOWN key to select the desired service menu item you want to adjust.
Press the Channel UP or DOWN key to select the desired service menu item you want to adjust.
Use the Volume + or – key to adjust the
data.
The + or – keys will increase or decrease the data sequentially.
3. Exit from the Service Menu:
Press the MENU key to turn off the Service Menu display.
The + or – keys will increase or decrease the data sequentially.
3. Exit from the Service Menu:
Press the MENU key to turn off the Service Menu display.
PROGRAM CODES
The microprossesor used in this model is a multi-purpose type and is used in several different models. To ensure proper operation and the correct features for your particular model, the program codes must be correct.
Note 1. Option Data 1 (NO. 087 OPT) should be hexadecimal 18. See 087 above. If this program code is wrong the TV will not operate properly.
The microprossesor used in this model is a multi-purpose type and is used in several different models. To ensure proper operation and the correct features for your particular model, the program codes must be correct.
Note 1. Option Data 1 (NO. 087 OPT) should be hexadecimal 18. See 087 above. If this program code is wrong the TV will not operate properly.
Note 2. Option Data 2 (NO. 088
OP2) should be hexadecimal 0A. See 088
above. If this program code is wrong the TV will not operate properly.
POWER FAILURE CIRCUIT
This unit is equipped with a Power Failure
Detector function included in the CPU which checks for an abnormal condition in
the chassis power supplies.
If, while the power is on, a failure is caused by any of the following that results in a low voltage supply, the CPU will turn the unit off in 1.5 seconds to prevent further damage:
# Failure within the power supply circuits.
# A short circuit in the load side from the supply.
1. Power Failure 1: Detected voltage failure for analog and digital circuits. (Connected to IC801 pin 32.)
2. Power Failure 2: Detected voltage failure for LVDS. (Connected to IC801 pin 36.)
(Normal: High; Failure: Low)
If, while the power is off, the power is switched on and any of these failures remains uncorrected, the CPU will shut off the power within three seconds.
If, while the power is on, a failure is caused by any of the following that results in a low voltage supply, the CPU will turn the unit off in 1.5 seconds to prevent further damage:
# Failure within the power supply circuits.
# A short circuit in the load side from the supply.
1. Power Failure 1: Detected voltage failure for analog and digital circuits. (Connected to IC801 pin 32.)
2. Power Failure 2: Detected voltage failure for LVDS. (Connected to IC801 pin 36.)
(Normal: High; Failure: Low)
If, while the power is off, the power is switched on and any of these failures remains uncorrected, the CPU will shut off the power within three seconds.
Check the following if the unit is
turned off by the power failure detector.
1. Disconnect the AC power cord (120V AC line) for at least 10 seconds.
2. Connect a DC Voltmeter to the circuits shown below.
3. Press the Power key and check for the proper voltage supplies.
4. If any of these voltages is low, the power failure detector should turn the unit off within three seconds.
5. Check all circuits shown below.
Note: This unit is equipped with a Power Surge Protection feature included in the CPU. If power failure occurs three times within 15 minutes, the CPU will stop functioning automatically to help prevent secondary damage. (TV will not turn on by pressing the power key.) To reset the operating programs within the CPU, disconnect the AC power cord for at least 10 seconds.
1. Disconnect the AC power cord (120V AC line) for at least 10 seconds.
2. Connect a DC Voltmeter to the circuits shown below.
3. Press the Power key and check for the proper voltage supplies.
4. If any of these voltages is low, the power failure detector should turn the unit off within three seconds.
5. Check all circuits shown below.
Note: This unit is equipped with a Power Surge Protection feature included in the CPU. If power failure occurs three times within 15 minutes, the CPU will stop functioning automatically to help prevent secondary damage. (TV will not turn on by pressing the power key.) To reset the operating programs within the CPU, disconnect the AC power cord for at least 10 seconds.
BACK CABINET REMOVAL
Remove 14 screws to take the cabinet back off
Remove 14 screws to take the cabinet back off
TROUBLESHOOTING
NO AUDIO
Check:
Line: IC001 6pin - IC801 (CPU) 38pin (Mute)
Parts: Around IC001 (Audio AMP.)
Line: IC001 6pin - IC801 (CPU) 38pin (Mute)
Parts: Around IC001 (Audio AMP.)
Audio Out only
Check:
IC3200 5pin (L) - Audio Out Terminal
IC3200 28pin (R) - Audio Out Terminal
Parts: Q1006, Q1007
IC3200 5pin (L) - Audio Out Terminal
IC3200 28pin (R) - Audio Out Terminal
Parts: Q1006, Q1007
RF (TV) only
Check:
A6100 3pin - Q6100 - IC6250 1pin (SIF)
IC6250 22pin - Q6251 - IC1251 1pin(R)
IC6250 23pin - Q6250 - IC1251 12pin(L)
Parts: Around A6100(TU), IC6250, Q6250, Q6251
A6100 3pin - Q6100 - IC6250 1pin (SIF)
IC6250 22pin - Q6251 - IC1251 1pin(R)
IC6250 23pin - Q6250 - IC1251 12pin(L)
Parts: Around A6100(TU), IC6250, Q6250, Q6251
Digital (TV) only
Check:
A6100 21, 20pin - IC6100 93, 94pin (IF)
IC5500 N4, U1pin - IC6300 5, 6pin (R),
IC5500 T1, T2pin - IC6300 3, 2pin (L),
IC6300 7pin - IC3200 31pin (R),
IC6300 1pin - IC3200 2pin (L),
Parts: Around A6100(TU), IC6100,IC5500,IC6300
A6100 21, 20pin - IC6100 93, 94pin (IF)
IC5500 N4, U1pin - IC6300 5, 6pin (R),
IC5500 T1, T2pin - IC6300 3, 2pin (L),
IC6300 7pin - IC3200 31pin (R),
IC6300 1pin - IC3200 2pin (L),
Parts: Around A6100(TU), IC6100,IC5500,IC6300
AV1, AV2, AV3 only
Check:
AV1 Terminal - IC1251 14pin (L), 5pin (R)
AV2 Terminal - IC1251 15pin (L), 2pin (R)
AV3 Terminal - IC1251 11pin (L), 4pin (R)
AV1 Terminal - IC1251 14pin (L), 5pin (R)
AV2 Terminal - IC1251 15pin (L), 2pin (R)
AV3 Terminal - IC1251 11pin (L), 4pin (R)
HDMI 1 / 2 / 3
Check:
Line: HDMI1 Terminal - IC6502
HDMI2 Terminal - IC6502
HDMI3 Terminal - IC6502
IC6502 21-40pin - IC5500 A1, B2,
C1-C3, D1-D2, E1-E3, F2-F3
Parts: Around IC6502, IC5500, IC6551
Line: HDMI1 Terminal - IC6502
HDMI2 Terminal - IC6502
HDMI3 Terminal - IC6502
IC6502 21-40pin - IC5500 A1, B2,
C1-C3, D1-D2, E1-E3, F2-F3
Parts: Around IC6502, IC5500, IC6551
NO VIDEO
RF (TV) only
Check:
Line: A6100 4pin - Q101 - IC1201 2pin
Parts: Around A6100 (TU_IF), Q101
Line: A6100 4pin - Q101 - IC1201 2pin
Parts: Around A6100 (TU_IF), Q101
AV2 only
Check:
Terminal(Y) - IC6200 12pin (Y)
Terminal(Cr) - IC6200 7pin (Cr)
Terminal(Cb) - IC6200 19pin (Cb)
Parts: Around
IC6200 (AD Converter)
Terminal(Y) - IC6200 12pin (Y)
Terminal(Cr) - IC6200 7pin (Cr)
Terminal(Cb) - IC6200 19pin (Cb)
Parts: Around
IC6200 (AD Converter)
AV3 only
Check:
Terminal(Y) - IC6200 26pin (Y)
Terminal(Cr) - IC6200 22pin (Cr)
Terminal(Cb) - IC6200 28pin (Cb)
Parts: Around
IC6200 (AD Converter)
Terminal(Y) - IC6200 26pin (Y)
Terminal(Cr) - IC6200 22pin (Cr)
Terminal(Cb) - IC6200 28pin (Cb)
Parts: Around
IC6200 (AD Converter)
Digital (TV) only
Check:
A6100 21, 20pin - IC6100 93, 94pin (IF)
Parts: Around
A6100 (TU, IF), IC6100
A6100 21, 20pin - IC6100 93, 94pin (IF)
Parts: Around
A6100 (TU, IF), IC6100
HDMI 1 / 2 / 3
Check:
HDMI1 Terminal - IC6502
HDMI2 Terminal - IC6502
HDMI3 Terminal - IC6502
IC6502 21~40pin - IC5500 A1, B2,
C1~C3, D1~D2, E1~E3, F2~F3
Parts: Around IC6502, IC5500
HDMI1 Terminal - IC6502
HDMI2 Terminal - IC6502
HDMI3 Terminal - IC6502
IC6502 21~40pin - IC5500 A1, B2,
C1~C3, D1~D2, E1~E3, F2~F3
Parts: Around IC6502, IC5500
All Inputs
Check:
Line: IC5500 - LCD Panel (RGB)
Parts: Around IC5500 (Screen Controller), LCD Panel,
Wire (K5LV: To LCD Panel)
Line: IC5500 - LCD Panel (RGB)
Parts: Around IC5500 (Screen Controller), LCD Panel,
Wire (K5LV: To LCD Panel)
