Contents of this article
- How to enter to service mode
- OLED panel test
- Led blinking codes
PANASONIC OLED TV TX-65CZ952B
Service mode
MPU controls the functions switching for each IICs through IIC bus in this chassis. The following setting and adjustment can be adjusted by remote control in Service Menu
How to enter into Service Mode
While pressing [VOLUME ( - )] button on the main unit, press the [RED] button on the remote control for 3 times within 2 seconds.
How to exit
Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control.
MPU controls the functions switching for each IICs through IIC bus in this chassis. The following setting and adjustment can be adjusted by remote control in Service Menu
How to enter into Service Mode
While pressing [VOLUME ( - )] button on the main unit, press the [RED] button on the remote control for 3 times within 2 seconds.
How to exit
Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control.
Key Command
# Press the (UP /DOWN /LEFT / RIGHT) button to step up/down/right/left through the functions and adjustments
# Press the OK button to change the adjustment values.
# Press the RETURN button for return to the main menu.
# Press the (UP /DOWN /LEFT / RIGHT) button to step up/down/right/left through the functions and adjustments
# Press the OK button to change the adjustment values.
# Press the RETURN button for return to the main menu.
Replacement of ICs:
PRO5 IC (IC8000) + eMMC(IC8920)
1. When Pro5 IC (IC8000) is replaced, eMMc (IC8920) should be also replaced with new one the same time.
2. When eMMc Memory (IC8920) is replaced, Pro5 IC (IC8000) is not necessary to be replaced the same time.
After the replacement of IC, SELF CHECK should be done to generate the final KEY data.
MTK IC (IC10000) + eMMC(IC14000)
1. When MTK IC (IC10000) is replaced, eMMc (IC14000) should be also replaced with new one the same time.
2. When eMMc Memory (IC14000) is replaced, MTK IC (IC10000) is not necessary to be replaced the same time.
After the replacement of IC, SELF CHECK should be done to generate the final KEY data.
How to SELF CHECK: While pressing [VOLUME ( - )] button on the main unit, press the MENU button on the remote control for more than 3 seconds.
TV will be forced to the factory shipment setting after this SELF CHECK
PRO5 IC (IC8000) + eMMC(IC8920)
1. When Pro5 IC (IC8000) is replaced, eMMc (IC8920) should be also replaced with new one the same time.
2. When eMMc Memory (IC8920) is replaced, Pro5 IC (IC8000) is not necessary to be replaced the same time.
After the replacement of IC, SELF CHECK should be done to generate the final KEY data.
MTK IC (IC10000) + eMMC(IC14000)
1. When MTK IC (IC10000) is replaced, eMMc (IC14000) should be also replaced with new one the same time.
2. When eMMc Memory (IC14000) is replaced, MTK IC (IC10000) is not necessary to be replaced the same time.
After the replacement of IC, SELF CHECK should be done to generate the final KEY data.
How to SELF CHECK: While pressing [VOLUME ( - )] button on the main unit, press the MENU button on the remote control for more than 3 seconds.
TV will be forced to the factory shipment setting after this SELF CHECK
Self Check
How to access
Self-check indication only:
While pressing [VOLUME ( - )] button on the main unit, press [BLUE] button on the remote control.
Self-check indication and forced to factory shipment setting:
While pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote control for more than 3 seconds.
How to exit
Switch off the power with the [POWER] button on the main unit.
How to access
Self-check indication only:
While pressing [VOLUME ( - )] button on the main unit, press [BLUE] button on the remote control.
Self-check indication and forced to factory shipment setting:
While pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote control for more than 3 seconds.
How to exit
Switch off the power with the [POWER] button on the main unit.
Power LED blinking
When abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the defective block can be identified by number of blinking of the Power LED on the front panel of the unit.
When abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the defective block can be identified by number of blinking of the Power LED on the front panel of the unit.
|
Blinking times
|
Contents
|
Check point
|
|
1
|
Panel
SOS
|
OLED
PANEL
|
|
2
|
EVDD(24V)_SOS
|
OLED
PANEL
P2 Board |
|
7
|
SUB3.3V_SOS
|
A
BOARD
P2 Board |
|
8
|
Power
SOS
|
P2
Board
|
|
9
|
SOUND
SOS
|
A
BOARD
Speaker |
|
10
|
GCX
SOS
|
FR
BOARD
|
|
13
|
EMERGENCY
SOS
|
A
BOARD
|
Panel adjustment function
The use of the OLED panel for a long period causes no uniformity of charge in each OLED cell and there is a possible cause of "image retention“.
To reduce the "image retention" Panel adjustment function is newly introduced for OLED models TX-65CZ950 series.
When "image retention" is not reduced by this function it seems that the "image retention" is permanent due to deterioration of OLED cell.
During the Panel adjustment period please avoid touching or exerting any pressure on the screen e.g. wiping the screen, etc.
If the Panel adjustment has been completed LED lights Red or Orange (standby mode).
The Panel adjustment function starts running automatically after switching off to standby if the TV has been in operation for at least 3 hours since the last panel adjustment.
If the Panel adjustment has been interrupted before completion it will start again after the next switching off to the standby mode.
How to activate Panel adjustment function manually:
Step 1. Change from “Home” mode to “Shop” mode
1. “MENU” button on remote control is pushed and while selecting "Picture" in menu press “Green” button on remote control for more than 3 seconds.
2. OSD screen (Figure 18) is displayed. "Shop" is selected.
Step 2. Pull out and insert the main plug. After TV turns on Panel adjustment function is activated.
Step 3. Change from “Shop” mode to “Home” mode after finish this function.
1. OSD screen (Figure 18) is displayed according to the procedure of Step1.
2. Select “Home” mode
Note: When TV has already been set to “Shop” mode the procedure of Step1 and Step3 is unnecessary.
The use of the OLED panel for a long period causes no uniformity of charge in each OLED cell and there is a possible cause of "image retention“.
To reduce the "image retention" Panel adjustment function is newly introduced for OLED models TX-65CZ950 series.
When "image retention" is not reduced by this function it seems that the "image retention" is permanent due to deterioration of OLED cell.
During the Panel adjustment period please avoid touching or exerting any pressure on the screen e.g. wiping the screen, etc.
If the Panel adjustment has been completed LED lights Red or Orange (standby mode).
The Panel adjustment function starts running automatically after switching off to standby if the TV has been in operation for at least 3 hours since the last panel adjustment.
If the Panel adjustment has been interrupted before completion it will start again after the next switching off to the standby mode.
How to activate Panel adjustment function manually:
Step 1. Change from “Home” mode to “Shop” mode
1. “MENU” button on remote control is pushed and while selecting "Picture" in menu press “Green” button on remote control for more than 3 seconds.
2. OSD screen (Figure 18) is displayed. "Shop" is selected.
Step 2. Pull out and insert the main plug. After TV turns on Panel adjustment function is activated.
Step 3. Change from “Shop” mode to “Home” mode after finish this function.
1. OSD screen (Figure 18) is displayed according to the procedure of Step1.
2. Select “Home” mode
Note: When TV has already been set to “Shop” mode the procedure of Step1 and Step3 is unnecessary.
OLED Panel Test Mode
Purpose:
To find the possible failure point where in OLED Panel, FR board or A board when the abnormal picture is displayed.
Procedure:
Step 1. Go into OLED Panel test mode and confirm the symptom
While pressing [VOLUME ( - )] button of the main unit, press [YELLOW] button of the remote control three times within 2 seconds.
The several test patterns generated by OLED Panel are displayed. Judge by the following method:
Still abnormal picture is displayed: The cause must be in OLED Panel. Exit test mode.
Normal picture is displayed: The cause must be in A board or FR board. Go into FR test mode
Purpose:
To find the possible failure point where in OLED Panel, FR board or A board when the abnormal picture is displayed.
Procedure:
Step 1. Go into OLED Panel test mode and confirm the symptom
While pressing [VOLUME ( - )] button of the main unit, press [YELLOW] button of the remote control three times within 2 seconds.
The several test patterns generated by OLED Panel are displayed. Judge by the following method:
Still abnormal picture is displayed: The cause must be in OLED Panel. Exit test mode.
Normal picture is displayed: The cause must be in A board or FR board. Go into FR test mode
Step 2. Go into FR test mode and confirm the symptom
During in OLED Panel test mode, press [OK] button on the remote control.
The test pattern generated by FR board is displayed. Judge by the following method:
Abnormal picture is displayed: The cause must be in FR board.
Normal picture is displayed: The cause must be in A board.
Step 3. Go into Additional OLED Panel test mode
During in FR test mode, press [OK] button on the remote control.
The several additional test patterns generated by OLED Panel are displayed.
Result and Judgment are same as step 1.
Step 4. How to Exit:
Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control in OLED Panel test mode or FR test mode.
Remarks:
1. During OLED Panel test mode and FR test mode, Power LED red and green are flashing alternately.
2. To display the test pattern in FR mode, input signal from HDMI, AV or antenna terminal. If no signal input, the test pattern won’t be generated and no test pattern is displayed.
During in OLED Panel test mode, press [OK] button on the remote control.
The test pattern generated by FR board is displayed. Judge by the following method:
Abnormal picture is displayed: The cause must be in FR board.
Normal picture is displayed: The cause must be in A board.
Step 3. Go into Additional OLED Panel test mode
During in FR test mode, press [OK] button on the remote control.
The several additional test patterns generated by OLED Panel are displayed.
Result and Judgment are same as step 1.
Step 4. How to Exit:
Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control in OLED Panel test mode or FR test mode.
Remarks:
1. During OLED Panel test mode and FR test mode, Power LED red and green are flashing alternately.
2. To display the test pattern in FR mode, input signal from HDMI, AV or antenna terminal. If no signal input, the test pattern won’t be generated and no test pattern is displayed.
Data Copy from TV set to USB Memory
1. Turn on the TV set.
2. Insert USB Memory with a startup file (pwd file) to USB Terminal.
On-screen Display will be appeared according to the startup file automatically.
3. Input a following password for (a) or (b) by using remote control.
(a) For Board replacement: 2770
(b) For Hotel: 4850
Data will be copied from TV set to USB Memory.
It takes around 2 to 6 minutes maximum for copying.
4. After the completion of copying to USB Memory, remove USB Memory from TV set.
5. Turn off the TV set.
Note:
Following new folder will be created in USB Memory for data from TV set.
(a) For Board replacement: user_setup
(b) For Hotel: hotel
1. Turn on the TV set.
2. Insert USB Memory with a startup file (pwd file) to USB Terminal.
On-screen Display will be appeared according to the startup file automatically.
3. Input a following password for (a) or (b) by using remote control.
(a) For Board replacement: 2770
(b) For Hotel: 4850
Data will be copied from TV set to USB Memory.
It takes around 2 to 6 minutes maximum for copying.
4. After the completion of copying to USB Memory, remove USB Memory from TV set.
5. Turn off the TV set.
Note:
Following new folder will be created in USB Memory for data from TV set.
(a) For Board replacement: user_setup
(b) For Hotel: hotel
Data Copy from USB Memory to TV set
1. Turn on the TV set.
2. Insert USB Memory with Data to USB Terminal.
On-screen Display will be appeared according to the Data folder automatically.
3. Input a following password for (a) or (b) by using remote control.
(a) For Board replacement: 2771
(b) For Hotel: 4851
Data will be copied from USB Memory to TV set.
4. After the completion of copying to USB Memory, remove USB Memory from TV set.
(a) For Board replacement: Data will be deleted after copying (Limited one copy).
(b) For Hotel: Data will not be deleted and can be used for other TVs.
5. Turn off the TV set.
Note:
1. Depending on the failure of boards, function of Data for board replacement does not work.
2. This function can be effective among the same model numbers.
1. Turn on the TV set.
2. Insert USB Memory with Data to USB Terminal.
On-screen Display will be appeared according to the Data folder automatically.
3. Input a following password for (a) or (b) by using remote control.
(a) For Board replacement: 2771
(b) For Hotel: 4851
Data will be copied from USB Memory to TV set.
4. After the completion of copying to USB Memory, remove USB Memory from TV set.
(a) For Board replacement: Data will be deleted after copying (Limited one copy).
(b) For Hotel: Data will not be deleted and can be used for other TVs.
5. Turn off the TV set.
Note:
1. Depending on the failure of boards, function of Data for board replacement does not work.
2. This function can be effective among the same model numbers.
Hotel Mode
Access command to the Hotel mode setup menu. In order to display the Hotel mode setup menu, please enter the following command (within 2 second). [TV] : Vol.[Down] + [REMOTE] : AV (3 times) Then, the Hotel mode setup menu is displayed.
Access command to the Hotel mode setup menu. In order to display the Hotel mode setup menu, please enter the following command (within 2 second). [TV] : Vol.[Down] + [REMOTE] : AV (3 times) Then, the Hotel mode setup menu is displayed.
To exit the “Hotel mode”: Switch off the power with the
[POWER] button on the main unit or the [POWER] button on the remote control or
pressing [EXIT] button on the remote control.
System Information
How to access
1. While pressing [MENU] button on the remote control.
2. To select [ Help] and then to select [System Information]
How to access
1. While pressing [MENU] button on the remote control.
2. To select [ Help] and then to select [System Information]
How to exit
Press the [RETURN] button on the remote control.
Press the [RETURN] button on the remote control.
Setting Inspection
Voltage Confirmation
Voltage Confirmation
A board
|
Description
|
Test
point
|
Voltage
|
|
USB5V
|
TP5440
|
5.17V
± 0.25V
|
|
USB1
|
TP8652
|
5.00V
± 0.25V
|
|
USB2
|
TP8660
|
5.00V
± 0.25V
|
|
USB3
|
TP8656
|
5.00V
± 0.25V
|
|
USB-WIFI
|
TP8650
|
5.2V
± 0.20V
|
|
SUB3.3V
|
TP5401
|
3.36V
± 0.15V
|
|
MTK3.3V
|
TP5200
|
3.33V
± 0.15V
|
|
DCDC3.3V
|
TP8970
|
3.00V
± 0.15V
|
|
HDMI3.3V
|
TP4507
|
3.33V
± 0.17V
|
|
SUB_AI_3.3V
|
TP2300
|
3.3V
± 0.17V
|
|
MT_STB3.3V
|
TP13019
|
3.3V
± 0.17V
|
|
STB_1.5V
|
TP11001
|
1.52V
± 0.07V
|
|
MTK_SUB1.0V
|
TP11000
|
1.02V
± 0.05V
|
|
AVDD1.0V
|
TP11002
|
1.06V
± 0.05V
|
|
SUB1.8V
|
TP8105
|
1.8V
± 0.9V
|
|
SUB_M_0.9V
|
TP8100
|
1.03V
± 0.09V
|
|
SUB_I_0.9V
|
TP8104
|
1.03V
± 0.09V
|
|
STB_I_1.8V
|
TP8108
|
1.8V
± 0.9V
|
|
STB_I_1.5V
|
TP8102
|
1.52V
± 0.07V
|
|
STB_I_1.2V
|
TP8109
|
1.29V
± 0.07V
|
|
STB_I_0.9V
|
TP8107
|
0.96V
± 0.13V
|
|
HDMI1.1V
|
TP4505
|
1.13V
± 0.06V
|
|
RIO1.2V
|
TP4504
|
1.22V
± 0.06V
|
|
WOL3.3V
|
TP8600
|
3.3V
± 0.17V
|
|
REG_1.8V
|
TP5702
|
1.84V
± 0.1V
|
|
LNB_PWR1
|
TP6702
|
18V ±
1.0V
|
|
SUB9V
|
TP5004
|
9V ±
0.4V
|
|
DMD_1.1V_3
|
TP5704
|
1.12V
± 0.11V
|
|
SUB_CI_5V
|
TP8400
|
5.0V
± 0.5V
|
|
SUB_CI_5V-B
|
TP8500
|
5.0V
± 0.5V
|
|
M_3.3V
|
TP8492
|
3.3V
± 0.17V
|
|
M_1.2V
|
TP8406
|
1.2V
± 0.12V
|
|
LNB_PWR2
|
TP6703
|
18V ±
1.0V
|
|
SUB5V
|
TP5420
|
5.06V
± 0.25V
|
Chassis
Board Layout
|
Board
Name
|
Function
|
|
A-Board
|
AV(COMPONENT/VIDEO),AV(SCART),
HDMI1-4, USB1-3, WI-FI, BLUETOOTH, Digital
Audio Out,TUNER A/DVB-T/T2/C(Sx2), DVB-T2/T/C/S2/S Dem 2x, CI slot 1x, Ethernet, Headphone jack, SERVICE PORT - RS-232C, Peaks IC_Pro5 + NAND FLASH eMMC,IC EASTER MTK + NAND FLASH eMMC, DDR3 SDRAM |
|
FR-Board
|
GCX2
2x, AUDIO AMP, SPEAKER+WOOFER+TWEETER output
|
|
P1-Board
|
Power
Supply
|
|
P2-Board
|
Power
Supply
|
|
K-Board
|
Remote
Receiver, Power and Timer LED, C.A.T.S
|
|
PN-Board
|
Temperature
Sensor
|
|
GK-Board
|
Control
Buttons
|
|
S-Board
|
Main
Power Switch
|
