Category: LCD Television Repair And Service
Contents of this article
- How to access to service mode
- Factory Initialization
- Power supply circuit
FUNAI LT6-M32
Service mode
How to set up the service mode
1. Use the service remote control unit.
2. Turn the power on.
3. Press the service button on the service remote control unit as shown in Fig bellow.
1. Use the service remote control unit.
2. Turn the power on.
3. Press the service button on the service remote control unit as shown in Fig bellow.
Purity Check Mode
This mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels.
1. Enter the Service mode.
2. Each time pressing [7] button on the service remote control unit, the display
1. Enter the Service mode.
2. Each time pressing [7] button on the service remote control unit, the display
VCOM Adjustment
1. Operate the unit for more than 20 minutes.
2. Set the color analyzer and bring the optical receptor to the center on the LCD-Panel surface after zero point calibration as shown above.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
3. Enter the Service mode.
4. [VCOM1]
Press [2] button on the service remote control unit.
[VCOM2]
Press [3] button on the service remote control unit.
5. Press [P UP/DOWN ] buttons on the service remote control unit so that the color analyzer value becomes minimum.
2. Set the color analyzer and bring the optical receptor to the center on the LCD-Panel surface after zero point calibration as shown above.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
3. Enter the Service mode.
4. [VCOM1]
Press [2] button on the service remote control unit.
[VCOM2]
Press [3] button on the service remote control unit.
5. Press [P UP/DOWN ] buttons on the service remote control unit so that the color analyzer value becomes minimum.
White Balance Adjustment
Purpose: To mix red, green and blue beams correctly for pure white.
Symptom of Misadjustment: White becomes bluish or reddish.
Purpose: To mix red, green and blue beams correctly for pure white.
Symptom of Misadjustment: White becomes bluish or reddish.
1. Operate the unit for more than 20 minutes.
2. Input the White Raster(70%=70IRE, 30%=30IRE).
2. Input the White Raster(70%=70IRE, 30%=30IRE).
3. Set the color analyzer to the CHROMA mode and bring the optical receptor to the center on the LCD-Panel surface after zero point calibration.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
4. Enter the Service mode. Press [ V -] button on the service remote control unit and select “C/D” mode.
4. Enter the Service mode. Press [ V -] button on the service remote control unit and select “C/D” mode.
5. [CUTOFF]
Press [3] button to select “COB” for Blue Cutoff adjustment. Press [1] button to select “COR” for Red Cutoff adjustment.
[DRIVE]
Press [6] button to select “DB” for Blue Drive adjustment. Press [4] button to select “DR” for Red
Drive adjustment.
6. In each color mode, press [P UP/DOWN ] buttons to adjust the values of color.
7. Adjust Cutoff and Drive so that the color temperature becomes 12000°K (x= 0.272 / y= 0.278 ±0.005).
Press [3] button to select “COB” for Blue Cutoff adjustment. Press [1] button to select “COR” for Red Cutoff adjustment.
[DRIVE]
Press [6] button to select “DB” for Blue Drive adjustment. Press [4] button to select “DR” for Red
Drive adjustment.
6. In each color mode, press [P UP/DOWN ] buttons to adjust the values of color.
7. Adjust Cutoff and Drive so that the color temperature becomes 12000°K (x= 0.272 / y= 0.278 ±0.005).
HOW TO INITIALIZE THE LCD TELEVISION
1. Turn the power on.
2. To enter the service mode, press the service button on the service remote control unit.
# To cancel the service mode, Press [POWER ] button on the remote control unit.1. Turn the power on.
2. To enter the service mode, press the service button on the service remote control unit.
3. Press [ i ] button on the service remote control unit to initialize the LCD television.
4. "INITIALIZED" will appear in the upper right of the screen. "INITIALIZED" color will change to green from red when initializing is complete.
4. "INITIALIZED" will appear in the upper right of the screen. "INITIALIZED" color will change to green from red when initializing is complete.
How to make the Service remote control unit
Cut “A” portion of the attached remote control unit as shown in Fig
Cut “A” portion of the attached remote control unit as shown in Fig
POWER SUPPLY CIRCUIT
CLICK ON THE IMAGE TO ZOOM IN
