Category: Blu Ray player Repair and Service
Contents of this article
- How to enter to Service mode
- Self Diagnosis
- Error codes
PANASONIC DMP-B200
Service Mode
Information necessary for service can be displayed.
Service mode setting:
1. Turn the power off.
2. Press the [SUB MNU] + [PLAY] and [VOL DOWN] button simultaneously for five seconds.
3. It is displayed on LCD as [SERV]. : It is shown to have entered the service mode.
4. The command is transmitted by attached remote control.
Method of making clear service mode : Press the power button (power off).
The display of information to each command is as follows.
NOTE:
Do not use it excluding the designated command.
Information necessary for service can be displayed.
Service mode setting:
1. Turn the power off.
2. Press the [SUB MNU] + [PLAY] and [VOL DOWN] button simultaneously for five seconds.
3. It is displayed on LCD as [SERV]. : It is shown to have entered the service mode.
4. The command is transmitted by attached remote control.
Method of making clear service mode : Press the power button (power off).
The display of information to each command is as follows.
NOTE:
Do not use it excluding the designated command.
Error Code Display
Press [0] [1] in service mode.
Press [0] [1] in service mode.
Last Error Code of U/F held by memory is dis played
on FL.
Details are described in "Self-Diagnosis Functions".
Details are described in "Self-Diagnosis Functions".
ROM Version Display
Press [0] [2] in service mode.
Press [0] [2] in service mode.
The display contents are switched over every 5 seconds.
1. Region code
2. Main firm version
3. Timer firm version
4. Drive firm version
5. ROM PATCH version
6. Firmware version
7. BOOT2 version
8. BOOT3 version
1. Region code
2. Main firm version
3. Timer firm version
4. Drive firm version
5. ROM PATCH version
6. Firmware version
7. BOOT2 version
8. BOOT3 version
Drive Check
Press [0] [3] in service mode.
Press [0] [3] in service mode.
Simple quality of BD drive
Laser Used Time Indication
Press [4] [1] in service mode
Press [4] [1] in service mode
Check laser used time (hours) of drive.
BD drive last error
Press [4] [2] in service mode.
Press [4] [2] in service mode.
BD drive error code display.
CEC (H) output check
Press [5] [5] in service mode.
Press [5] [5] in service mode.
Check of the CEC terminal high output of HDMI.
CEC (L) output check
Press [5] [6] in service mode.
Press [5] [6] in service mode.
Check of the CEC terminal low output of HDMI.
Manufacturing Date
Press[6][1]in service mode.
Press[6][1]in service mode.
Read out the manufacturing date of the unit.
Drive adjustment value initialization
Press[7][1]in service mode.
Press[7][1]in service mode.
Initialize the drive going to factory
production adjustment values.
Release Service Mode
Press [POWER] button on the front panel or Remote
controller in service mode.
Self-Diagnosis Functions
Self-Diagnosis Function provides information for errors to service personnel by “Self-Diagnosis Display” when any error has occurred.
U** and F** are stored in memory and held.
You can check latest error code by transmitting [0] [1] of Remote Controller in Service Mode. In case of clear the self-diagnosis display, remove the battery pack and the AC adaptor from the main unit after the power of the main unit is turned off.
Self-Diagnosis Function provides information for errors to service personnel by “Self-Diagnosis Display” when any error has occurred.
U** and F** are stored in memory and held.
You can check latest error code by transmitting [0] [1] of Remote Controller in Service Mode. In case of clear the self-diagnosis display, remove the battery pack and the AC adaptor from the main unit after the power of the main unit is turned off.
ERROR CODES
Error Code
|
Diagnosis contents
|
Description
|
U580
|
Battery
supply current abnormality
|
A
problem has occurred with the battery pack.
|
U581
|
Abnormal
charge time on battery power
|
The
battery pack has been recharging but has failed to
recharge for some reason. Recharge again. |
U582
|
Battery-powered
temperature anomaly
|
You
are recharging in a location that is too hot or too cold.
Recharge at normal temperature [+5 to +35 Degree C (+41 to +95 F)]. |
U59
|
Abnormal
inner temperature detected
|
Display
appears when drive temperature exceeds 70 Degree C.
The power is turned off forcibly. For 30 minutes after this, all key entries are disabled. The event is saved in memory as well. |
U72
|
HDMI
connection error
(communication error) |
This
error is displayed when there are any communication
problems with the unit and the equipments (TV, amplifier etc.) connected to the unit by HDMI. (or when there is a problem with the HDMI cable). The display disappears only when the connection is released. Neither the button operation nor the passage of the fixed time disappear the display. |
U73
|
HDMI
connection error
(authentication error) |
When
authentication error occurs while the equipments (TV, amplifier etc.) are connected by HDMI. (or when there is a problem with the HDMI cable).
The display disappears only when the connection is released. Neither the button operation nor the passage of the fixed time disappear the display. |
U76
|
Connection
error
|
This
error is displayed when equipment such as TVs or amplifiers connected to the unit with the HDMI cable do not correspond to the copyright protection. (The BD/DVD video where the copyright is protected cannot be played.)
|
U77
|
Illegal
disc error
|
This
error is displayed when it becomes impossible to reproduce because of copyright illegal information.
|
U88
|
Restoration
is operation.
(When the disc is in the disc tray) |
This
error is displayed when there is a disc in the disc tray or abnormality is confirmed during playback. It is shown that the restoration to return the main unit operation normally is operating. It becomes possible to use as soon as not the breakdown but the U88 display disappears.
|
F00
|
No
error information
|
Initial
setting for error code in memory (Error code Initialization is possible with error code initialization and main unit initialization.)
|
F58
|
Drive
hardware error
|
When
drive unit error is detected, the event is saved in memory.
|
F74
|
HDMI
Device Key Communication
error |
This
error is displayed when the information error is occurred at HDMI device key loading.
|
F75
|
HDMI
Device Key Loading error
|
This
error is displayed when the key of loaded is illegal at
HDMI device key loading. |
