Category: Digital camera Repair and Service
Contents of this article
- How to Access service mode
- Factory Reset
- Error codes and causes
PANASONIC HDC-SD100
Factory Setting
HOW TO TURN ON THE FACTORY SETTINGS
1. Set the mode dial “Recording” mode.
2. While keep pressing the “[LEFT<] of cursor” button and “delete” button, hold down the Mode Select Switch towards to “[FOCUS]” position for more than 3 seconds until the top screen of the Service Menu being displayed.
HOW TO TURN ON THE FACTORY SETTINGS
1. Set the mode dial “Recording” mode.
2. While keep pressing the “[LEFT<] of cursor” button and “delete” button, hold down the Mode Select Switch towards to “[FOCUS]” position for more than 3 seconds until the top screen of the Service Menu being displayed.
3. Under the condition of the Item No.”1” is
yellow high lighted, press the “[RIGHT>] of cursor“ button.
4. By pressing the “[UP ] of cursor” button, then press the “[center] of cursor” button.
5. After few seconds “END” is displayed on LCD monitor. Cutting of battery connection or AC power supply connection as a completion of the “FACTORY SETTINGS”.
4. By pressing the “[UP ] of cursor” button, then press the “[center] of cursor” button.
5. After few seconds “END” is displayed on LCD monitor. Cutting of battery connection or AC power supply connection as a completion of the “FACTORY SETTINGS”.
The factory settings clean up and/or refresh
the following settings.
1. The OSD MENU setting data.
2. Deletion only for all scene files in a card and format of the MPEG2 file system area.
3. Reset the folder number and file number of still pictures.
(Setting the folder number is 100, and file number is 0.)
4. Clear the mechanism lock information.
5. Clear the service mode information contents.
1. The OSD MENU setting data.
2. Deletion only for all scene files in a card and format of the MPEG2 file system area.
3. Reset the folder number and file number of still pictures.
(Setting the folder number is 100, and file number is 0.)
4. Clear the mechanism lock information.
5. Clear the service mode information contents.
Service Mode
1. Indication method of the service menu
Set the mode dial “Recording” mode.
2. While keep pressing the “[LEFT<] of cursor” button and “delete” button, hold down the Mode Select Switch towards to
“[FOCUS]” position for more than 3 seconds until the top screen of the Service Menu being displayed.
1. Indication method of the service menu
Set the mode dial “Recording” mode.
2. While keep pressing the “[LEFT<] of cursor” button and “delete” button, hold down the Mode Select Switch towards to
“[FOCUS]” position for more than 3 seconds until the top screen of the Service Menu being displayed.
Service mode menu
|
Screen display
|
Contents
|
Function
|
|
1
|
Factory
settings
|
Function
to throw a product up in a factory shipment state
|
|
4
|
Lock
search history indication
|
Display
an error cord for three histories saved in EEPROM
|
NOTE:
Do not using service mode except above table of Service Menu.
3. End method of the top screen of the service menu. Push the menu button to end the service mode, and then POWER OFF.
Do not using service mode except above table of Service Menu.
3. End method of the top screen of the service menu. Push the menu button to end the service mode, and then POWER OFF.
Lock Search History Indication
1. Set the mode dial “Recording” mode.
2. While keep pressing the “[LEFT<] of cursor” button and “delete” button, hold down the Mode Select Switch towards to “[FOCUS]” position for more than 3 seconds until the top screen of the Service Menu being displayed.
3. Select [ 4 ] Lock search history indication.
1. Set the mode dial “Recording” mode.
2. While keep pressing the “[LEFT<] of cursor” button and “delete” button, hold down the Mode Select Switch towards to “[FOCUS]” position for more than 3 seconds until the top screen of the Service Menu being displayed.
3. Select [ 4 ] Lock search history indication.
Indication contents
# Lock search history indication
Display the camera system error cord for three histories saved in EEPROM.
# The error cord contents which are displayed
# Lock search history indication
Display the camera system error cord for three histories saved in EEPROM.
# The error cord contents which are displayed
ERROR CODES
|
Error code
|
Function
|
|
51
|
Focus
control is abnormal
|
|
52
|
Zoom
control is abnormal
|
|
53
|
OIS
lens control is abnormal
|
|
71
|
Lens
cover open/close is abnormal
|
|
72
|
Cooling
fan is abnormal
|
|
73
|
High
temperature is abnormal
|
|
33
|
Communication
between camera to ARM is abnormal
|
Electric Adjustment
# Adjustment method is different from a conventional SD video camera.
# An exclusive jig and PC (including software for adjustment “Tatsujin”) are necessary for electric adjustment.
# A USB driver for service is necessary to communication with PC.
# Connection method of the main unit and an exclusive adjustment jig as follows
Adjustment Procedure
# Connect the main unit to PC with USB.
The adjustment instruction is available at "Software download" on the "Support Information from NWBG/VDBG-PAVC" web-site in "TSN System".
# An exclusive jig and PC (including software for adjustment “Tatsujin”) are necessary for electric adjustment.
# A USB driver for service is necessary to communication with PC.
# Connection method of the main unit and an exclusive adjustment jig as follows
Adjustment Procedure
# Connect the main unit to PC with USB.
The adjustment instruction is available at "Software download" on the "Support Information from NWBG/VDBG-PAVC" web-site in "TSN System".
Connection Diagram
CLICK ON THE IMAGE TO ZOOM IN
