PHILIPS CITY LINE BERLIN VACUUM CLEANER
FC8421
CIRCUIT AND DISASSEMBLING
TECHNICAL INFORMATION
- Maximum air displacement : 34 l/sec.
- Maximum vacuum water column : 260 cm
- Power consumption (IEC) 225V : 1500 W
- Dust storage capacity : 2 l
- Cord length (depends on version) : 6 m
- Filter system : 5 filters
- Dimensions of cleaner : 382 x 292 x 218 mm
- Dimensions of packaging : 510 x 305 x 330 mm
- Net weight : 4.5 Kg
- Gross weight : 8,0 Kg
- Noise : 79 dB
- Maximum air displacement : 34 l/sec.
- Maximum vacuum water column : 260 cm
- Power consumption (IEC) 225V : 1500 W
- Dust storage capacity : 2 l
- Cord length (depends on version) : 6 m
- Filter system : 5 filters
- Dimensions of cleaner : 382 x 292 x 218 mm
- Dimensions of packaging : 510 x 305 x 330 mm
- Net weight : 4.5 Kg
- Gross weight : 8,0 Kg
- Noise : 79 dB
DISASSEMBLY- AND RE-ASSEMBLY ADVISE
First lift and remove the knob and printed knob base and then loosen mounting screws A.
First lift and remove the knob and printed knob base and then loosen mounting screws A.
Lift the motor housing (item 26) out of the lower housing and
take out the cord winder unit.
To disassemble the cord winder, use TORX screwdriver no. T10, which is one of
a set consisting of T20; T15; T10; T9; T8; T7 and T6 (code number 4822 395
50145).
REPAIR INSTRUCTION
- The spare parts have been standardized as much as possible.
- Cotton dustbags are used in countries where paper dustbags are unobtainable.
- If the reel half spring unit is replaced, shaft F must be lubricated with silicone grease. Do not apply any silicone grease to or spill any grease on terminals (36) or conductors (35).
- Item 34 is provided with a long cord-winder spring, but both long and short cords can be used in combination with this spring. (L = 9.3 m)
- Depending on the length of the original cord, the spare cord may have to be shortened.
- The cord winder spring must be tensioned to the maximum level and then be rewound approx. 1.5 turn.
- The RPM can be adjusted by means of the potentiometer mounted on the PCB (item 25). The RPM is correctly adjusted if the motor starts automatically and continues to run smoothly with the ON/OFF position and the adjustable potentiometer in minimum position.
- If the function of the electronic control unit (item 25) is not required, the Triac must be short-circuited in the manner shown in the circuit diagram.
- When the vacuum cleaner is used to suck up fine dust, the pores of the dustbag may become clogged, causing the passage of air through the dustbag to become obstructed. As a result, the dustbag-full indicator will indicate that the dustbag needs to be replaced, even though the dustbag is not full at all.
- The spare parts have been standardized as much as possible.
- Cotton dustbags are used in countries where paper dustbags are unobtainable.
- If the reel half spring unit is replaced, shaft F must be lubricated with silicone grease. Do not apply any silicone grease to or spill any grease on terminals (36) or conductors (35).
- Item 34 is provided with a long cord-winder spring, but both long and short cords can be used in combination with this spring. (L = 9.3 m)
- Depending on the length of the original cord, the spare cord may have to be shortened.
- The cord winder spring must be tensioned to the maximum level and then be rewound approx. 1.5 turn.
- The RPM can be adjusted by means of the potentiometer mounted on the PCB (item 25). The RPM is correctly adjusted if the motor starts automatically and continues to run smoothly with the ON/OFF position and the adjustable potentiometer in minimum position.
- If the function of the electronic control unit (item 25) is not required, the Triac must be short-circuited in the manner shown in the circuit diagram.
- When the vacuum cleaner is used to suck up fine dust, the pores of the dustbag may become clogged, causing the passage of air through the dustbag to become obstructed. As a result, the dustbag-full indicator will indicate that the dustbag needs to be replaced, even though the dustbag is not full at all.
PARTS LIST
|
Service code
|
Description
|
Service code
|
Description
|
|
4341
009 00680
|
handle
|
4322
009 06430
|
motor
ANS 1451 230 V
|
|
4341
009 00730
|
dust
cover
|
4322
009 06770
|
motor
ANS 1241 EL 120 V
|
|
8838
021 00000
|
S-bag
set
|
4822
466 62655
|
buffer
ring front
|
|
4822
480 10115
|
cotton
dustbag
|
4341
003 02360
|
ANS
motor disc
|
|
4341
009 00760
|
dustbag
frame
|
4322
003 06620
|
push
rod
|
|
4341
001 70180
|
dust
cover sealing
|
4322
001 72360
|
brake
tyre
|
|
4341
009 00800
|
lowerhousing
assy
|
4322
009 07640
|
base
plate assy
|
|
4341
001 70190
|
inlet
rubber
|
4322
009 07610
|
reel
half spring unit
|
|
4341
003 02180
|
nose
piece
|
4322
009 09060
|
reel
half spring unit PRC
|
|
4341
009 00790
|
rear
wheel standard
|
4341
005 01330
|
reel
half contact side
|
|
4322
003 12220
|
wheel
bush
|
4341
005 00790
|
contact
plate assy
|
|
4822
480 40234
|
safety
filter
|
4322
006 01770
|
flat
cord set Japan/Taiwan 5.3 m
|
|
4341
009 00770
|
caster
assy
|
4341
006 01890
|
cordset
1.0 / 5.3 m PRC / R
|
|
4341
009 00780
|
cover
and filter
|
4322
006 02100
|
flat
cord set U.K./H.K. 6.3 m fl
|
|
4341
005 00780
|
turn
knob grip stand
|
4322
006 02060
|
at cord
set Euro/Korea 6.3 m
|
|
4341
005 01360
|
knob
base
|
4322
006 02080
|
flat
cord set Swiss
|
|
4341
003 02280
|
cord
outlet
|
4322
003 17380
|
bend
con.
|
|
4341
009 00810
|
upper
housing
|
4341
004 20450
|
bend
and hose assy
|
|
4341
003 02310
|
pedal
|
4322
002 22610
|
metal
tube con. (opt.)
|
|
4341
003 02250
|
AFS
back grille
|
4322
004 22990
|
telesc.tube
con.
|
|
4822
015 70056
|
AFS
filter
|
4341
003 02470
|
accessory
clip
|
|
4341
003 02240
|
wheel
peg
|
4341
004 20170
|
crevice
nozzle con.
|
|
4341
003 02330
|
cooling
tube
|
4341
004 20100
|
small
nozzle con.
|
|
4341
003 02390
|
switch
lever
|
4341
004 20190
|
dusting
brush con. (opt.)
|
|
4322
006 50600
|
switch
soldered
|
4322
004 22940
|
big
nozzle con.
|
|
4341
006 20560
|
PCB ANS
EL 220 - 240 V
|
4322
004 22330
|
twist
& clean nozzle con. (opt.)
|
|
4341
006 20570
|
PCB ANS
EL 120 V
|
4322
005 11040
|
polishing
disc (opt.)
|
|
4341
003 02320
|
motor
cap
|
8838
041 01010
|
pads
for twist & clean nozzle (opt.)
|
|
4341
001 70210
|
buffer
back
|
|
|
ELECTRICAL DIAGRAM
EXPLODED VIEW
CLICK ON THE IMAGES TO ZOOM IN
