Contents of this article
- Error code
- Causes
- Remedies
Canon CLC4040
color printer
Error
code causes and remedies
E000-0001
Insufficient temperature rise of fixing unit when power
is turned ON
When the temperature of the fixing belt main thermistor failed to reach 50 deg C within 120 sec. after the fixing belt temperature regulation has started.
When the temperature of the fixing belt main thermistor failed to reach 50 deg C within 120 sec. after the fixing belt temperature regulation has started.
Check for broken or disconnected heater wires. Checking
Disconnection of the Connector in the Thermistor Wiring. Replace the fixing
belt unit. Replace the fixer. Replace the IH power supply PCB and AC driver
PCB. Replace the DC controller PCB 2 (MAISY). In the service mode, clear the
error by selecting COPIER > FUNCTION > CLEAR > ERR.
E000-0101
Insufficient temperature rise of fixing unit when power
is turned ON
When the temperature of the pressure belt main thermistor failed to reach 50 deg C within 120 sec. after the pressure belt temperature regulation has started.
When the temperature of the pressure belt main thermistor failed to reach 50 deg C within 120 sec. after the pressure belt temperature regulation has started.
Check for broken or disconnected heater wires. Replace
the fixing belt unit. Checking Disconnection of the Connector in the Thermistor
Wiring. Replace the fixer and AC driver PCB. Replace the DC controller PCB 2
(MAISY). In the service mode, clear the error by selecting COPIER > FUNCTION
> CLEAR > ERR.
E001-0001
Abnormally high temperature rise of fixing unit (circuit
trouble)
When the fixing belt main thermistor has detected a high temperature (ASIC detection).
When the fixing belt main thermistor has detected a high temperature (ASIC detection).
Check the connection of the connector in the thermistor
wiring (wirepinching, disconnection). Replace the fixing unit. Replace the IH
unit, halogen heater, fixer and AC driver PCB. Replace the DC controller PCB 2
(MAISY). In the service mode, clear the error by selecting COPIER > FUNCTION
> CLEAR > ERR.
E001-0002
Abnormally high temperature rise of fixing unit (circuit
trouble)
When fixing sub-thermistor 1 has detected a high temperature (ASIC detection).
When fixing sub-thermistor 1 has detected a high temperature (ASIC detection).
Check the connection of the connector in the thermistor
wiring (wirepinching, disconnection). Replace the fixing unit. Replace the IH
unit, halogen heater, fixer and AC driver PCB. Replace the DC controller PCB 2
(MAISY). In the service mode, clear the error by selecting COPIER > FUNCTION
> CLEAR > ERR.
E001-0003
Abnormally high temperature rise of fixing unit (circuit
trouble)
When fixing sub-thermistor 2 has detected a high temperature (ASIC detection).
When fixing sub-thermistor 2 has detected a high temperature (ASIC detection).
Check the connection of the connector in the thermistor
wiring (wirepinching, disconnection). Replace the fixing unit. Replace the IH
unit, halogen heater, fixer and AC driver PCB. Replace the DC controller PCB 2
(MAISY). In the service mode, clear the error by selecting COPIER > FUNCTION
> CLEAR > ERR.
E001-0101
Abnormally high temperature rise of fixing unit (circuit
trouble)
When pressure main thermistor has detected a high temperature (ASIC detection).
When pressure main thermistor has detected a high temperature (ASIC detection).
Check the connection of the connector in the thermistor
wiring (wirepinching, disconnection). Replace the fixing unit. Replace the IH
unit, halogen heater, fixer and AC driver PCB. Replace the DC controller PCB 2
(MAISY). In the service mode, clear the error by selecting COPIER > FUNCTION
> CLEAR > ERR.
E001-0102
Abnormally high temperature rise of fixing unit (circuit
trouble)
When pressure sub-thermistor 1 has detected a high temperature (ASIC detection).
When pressure sub-thermistor 1 has detected a high temperature (ASIC detection).
Check the connection of the connector in the thermistor
wiring (wirepinching, disconnection). Replace the fixing unit. Replace the IH
unit, halogen heater, fixer and AC driver PCB. Replace the DC controller PCB 2
(MAISY). In the service mode, clear the error by selecting COPIER > FUNCTION
> CLEAR > ERR.
E001-0103
Abnormally high temperature rise of fixing unit (circuit
trouble)
When pressure sub-thermistor 2 has detected a high temperature (ASIC detection).
When pressure sub-thermistor 2 has detected a high temperature (ASIC detection).
Check the connection of the connector in the thermistor
wiring (wirepinching, disconnection). Replace the fixing unit. Replace the IH
unit, halogen heater, fixer and AC driver PCB. Replace the DC controller PCB 2
(MAISY). In the service mode, clear the error by selecting COPIER > FUNCTION
> CLEAR > ERR.
E002-0002
Insufficient temperature rise of fixing unit
When the fixing main thermistor fails to reach 80 deg C within the prescribed period of time after reaching 50 deg C during warm-up.
When the fixing main thermistor fails to reach 80 deg C within the prescribed period of time after reaching 50 deg C during warm-up.
Replace the fixing belt unit. Replace the fixer and AC
driver PCB. Replace the DC controller PCB 2 (MAISY). In the service mode, clear
the error by selecting COPIER > FUNCTION > CLEAR > ERR.
E002-0003
Insufficient temperature rise of fixing unit
When the fixing main thermistor fails to reach 110 deg C within the prescribed period of time after reaching 80 deg C during warm-up.
When the fixing main thermistor fails to reach 110 deg C within the prescribed period of time after reaching 80 deg C during warm-up.
Replace the fixing belt unit. Replace the fixer and AC
driver PCB. Replace the DC controller PCB 2 (MAISY). In the service mode, clear
the error by selecting COPIER > FUNCTION > CLEAR > ERR.
E002-0004
Insufficient temperature rise of fixing unit
When the fixing main thermistor fails to reach 130 deg C within the prescribed period of time after reaching 110 deg C during warm-up.
When the fixing main thermistor fails to reach 130 deg C within the prescribed period of time after reaching 110 deg C during warm-up.
Replace the fixing belt unit. Replace the fixer and AC
driver PCB. Replace the DC controller PCB 2 (MAISY). In the service mode, clear
the error by selecting COPIER > FUNCTION > CLEAR > ERR.
E002-0005
Insufficient temperature rise of fixing unit
When the fixing main thermistor fails to reach 170 deg C within the prescribed period of time after reaching 150 deg C during warm-up.
When the fixing main thermistor fails to reach 170 deg C within the prescribed period of time after reaching 150 deg C during warm-up.
Replace the fixing belt unit. Replace the fixer and AC
driver PCB. Replace the DC controller PCB 2 (MAISY). In the service mode, clear
the error by selecting COPIER > FUNCTION > CLEAR > ERR.
E002-0101
Insufficient temperature rise of fixing unit
When the pressure main thermistor fails to reach 80 deg C within the prescribed period of time after reaching 50 deg C during warm-up.
When the pressure main thermistor fails to reach 80 deg C within the prescribed period of time after reaching 50 deg C during warm-up.
Replace the fixing belt unit. Replace the fixer and AC
driver PCB. Replace the DC controller PCB 2 (MAISY). In the service mode, clear
the error by selecting COPIER > FUNCTION > CLEAR > ERR.
E002-0102
Insufficient temperature rise of fixing unit
When the pressure main thermistor fails to reach 100 deg C within the prescribed period of time after reaching 80 deg C during warm-up.
When the pressure main thermistor fails to reach 100 deg C within the prescribed period of time after reaching 80 deg C during warm-up.
Replace the fixing belt unit. Replace the fixer and AC
driver PCB. Replace the DC controller PCB 2 (MAISY). In the service mode, clear
the error by selecting COPIER > FUNCTION > CLEAR > ERR.
