OPTOMA HD67
Lamp Reset
1. Get into service mode
2. Use "up" or "down" buttons to select "Exit", then use "left" or "right" buttons to re-write the lamp hour back to previous lamp usage hour.
3. Press "Enter" to exit the service mode.
Note: left key = decrease lamp hour
right key =increase lamp hour
1. Get into service mode
2. Use "up" or "down" buttons to select "Exit", then use "left" or "right" buttons to re-write the lamp hour back to previous lamp usage hour.
3. Press "Enter" to exit the service mode.
Note: left key = decrease lamp hour
right key =increase lamp hour
Troubleshooting
LED Blinking
Message
|
Power
LED
(Red / Green)
|
Temp
LED
(Red)
|
Lamp
LED
(Red)
|
Standby
State (input power cord)
|
Red
|
No light
|
No light
|
Power
on (warming)
|
Flashing
Green
|
No light
|
No light
|
Lamp
lighting
|
Green
|
No light
|
No light
|
Power
off (Cooling)
|
Flashing
Green
|
No light
|
No light
|
Error
(Lamp failed)
|
Flashing
Red
|
No light
|
Steady light
|
Error
(Fan failed)
|
Flashing
Red
|
Flashing
|
No light
|
Error
(Over Temp.)
|
Flashing
Red
|
Steady light
|
No light
|
No Power
Ensure the Power Cord and AC Power Outlet
are securely connected
- Check Lamp Cover , Interrupt Switch
- Ensure all connectors are securely connected and aren’t broken
- Check LVPS
- Check Lamp Driver
- Check Main Board
- Check Lamp Cover , Interrupt Switch
- Ensure all connectors are securely connected and aren’t broken
- Check LVPS
- Check Lamp Driver
- Check Main Board
Auto Shut Down
- Check LED Status
a. Lamp Fail: Power LED ( LED (flashes red), Lamp LED (lights red) red), Lamp LED (lights red)
- Check Lamp
- Check Lamp Driver
- Check Main Board
b. Over Temp.:Power LED ( LED (flashes red), Temp LED (lights red) red), Temp LED (lights red) Temp LED (lights red)
- Check Fan
- Check Main Board
c. Fan Fail:Power LED ( LED (flashes red), Temp LED (Flashes red) red), Temp LED (Flashes red) Temp LED (Flashes red)
- Check Fan
- Check Main Board
a. Lamp Fail: Power LED ( LED (flashes red), Lamp LED (lights red) red), Lamp LED (lights red)
- Check Lamp
- Check Lamp Driver
- Check Main Board
b. Over Temp.:Power LED ( LED (flashes red), Temp LED (lights red) red), Temp LED (lights red) Temp LED (lights red)
- Check Fan
- Check Main Board
c. Fan Fail:Power LED ( LED (flashes red), Temp LED (Flashes red) red), Temp LED (Flashes red) Temp LED (Flashes red)
- Check Fan
- Check Main Board
No Light On
- Ensure all connectors are securely
connected and aren’t broken
- Check Lamp Module
- Check Lamp Driver
- Check LVPS
- Check Main Board
- Check Color Wheel
- Check Photo Sensor Board
- Check Lamp Module
- Check Lamp Driver
- Check LVPS
- Check Main Board
- Check Color Wheel
- Check Photo Sensor Board
No Image
- Ensure the Signal Cable and Source work
(If you connect multiple sources at the same time, use the “Source” button switch)
- Ensure all connectors are securely connected and aren’t broken
- Check Main Board
- Check DMD Board
- Check DMD Chip
- Check Color Wheel
- Check Engine Module
(If you connect multiple sources at the same time, use the “Source” button switch)
- Ensure all connectors are securely connected and aren’t broken
- Check Main Board
- Check DMD Board
- Check DMD Chip
- Check Color Wheel
- Check Engine Module
3D Image Abnormal
- Ensure the using 3D glasses is good and
you must face the projection.
- Ensure the CD in DVD is HQFS format or the graphic card from PC can support 3D format.
- Ensure your standing distance is less than 6m from screen.
- Ensure the 3D function is on and execute “3D sync invert” in OSD menu.
- Check main board.
- Ensure the CD in DVD is HQFS format or the graphic card from PC can support 3D format.
- Ensure your standing distance is less than 6m from screen.
- Ensure the 3D function is on and execute “3D sync invert” in OSD menu.
- Check main board.
Service Mode
1. Turn on the projector
2. Do the following actions sequentially to get into service mode
(1) Press "Power", "Left", "Left" and "Menu" buttons sequentially on remote controller.
(2) Service Mode will be shown.
(3) Choose "Exit" to leave the Service Mode after confirming the configuration.
2. Do the following actions sequentially to get into service mode
(1) Press "Power", "Left", "Left" and "Menu" buttons sequentially on remote controller.
(2) Service Mode will be shown.
(3) Choose "Exit" to leave the Service Mode after confirming the configuration.
Factory Fan RPM Reset
After replace main board, Fan, upgrade system FW, it’s necessary to do:
1. Plug in the power cord, power on the projector, when the “logo” disappear, press “Power”, “Left”, “Left” and “right” button in sequence.
2. After about 70 seconds, you can check the fan RPM :
a. Please get into Service Mode
After replace main board, Fan, upgrade system FW, it’s necessary to do:
1. Plug in the power cord, power on the projector, when the “logo” disappear, press “Power”, “Left”, “Left” and “right” button in sequence.
2. After about 70 seconds, you can check the fan RPM :
a. Please get into Service Mode
b. To select “RD MENU”, then press “OK”,
Fan detail information will be shown.
Note: After about 70 seconds,If the blower speed(>70 sec) is not between 2800-3200,you must change fan.
Note: After about 70 seconds,If the blower speed(>70 sec) is not between 2800-3200,you must change fan.
PC MODE
Note: - Test signal: analog 1280 x 720 @60Hz
- Connect VGA IN port of Projector with VGA port of Chroma and connect VGA Out port of Projector with VGA port of Monitor by VGA cable, check if the Projected image and the LCD image are the same.
Note: - Test signal: analog 1280 x 720 @60Hz
- Connect VGA IN port of Projector with VGA port of Chroma and connect VGA Out port of Projector with VGA port of Monitor by VGA cable, check if the Projected image and the LCD image are the same.
