SAMSUNG UN40B6000VM
SERVICE MODE
Entering Factory Mode
To enter ‘Service Mode’ Press the remote -control keys in this sequence :
# If you do not have Factory remote – control
To enter ‘Service Mode’ Press the remote -control keys in this sequence :
# If you do not have Factory remote – control
MUTE > Number Key(1) > Number Key(8) >
Number Key(2) > Power on
# If you have Factory remote - control
PICTURE ON > DISPLAY > FACTORY
PICTURE ON > DISPLAY > FACTORY
The buttons are active in the service mode.
1. Remote - Control Key : Power, Arrow Up, Arrow Down, Arrow Left Arrow Right, Menu, Enter, Number Key(0~9)
2. Function - Control Key : Power, CH +, CH -, VOL +, VOL -, Menu, TV/VIDEO(Enter)
1. Remote - Control Key : Power, Arrow Up, Arrow Down, Arrow Left Arrow Right, Menu, Enter, Number Key(0~9)
2. Function - Control Key : Power, CH +, CH -, VOL +, VOL -, Menu, TV/VIDEO(Enter)
Checking the panel
You have to check Panel Maker Because of different adjustments as follows.
First of all, Check the label rating!
1) Label Rating File
- LCD PANEL MARK
A:ACER(AUO) S : SEC C : CMO
* If not printed you could consider S(sec) panel mark.
You have to check Panel Maker Because of different adjustments as follows.
First of all, Check the label rating!
1) Label Rating File
- LCD PANEL MARK
A:ACER(AUO) S : SEC C : CMO
* If not printed you could consider S(sec) panel mark.
White Balance – Calibration
You must perform Calibration in the Lattice
Pattern before adjusting the White Balance.
Color Calibration
Adjust spec.
1. Source : HDMI
2. Setting Mode : 1280*720@60Hz
3. Pattern : Pattern #24 (Chess Pattern)
Adjust spec.
1. Source : HDMI
2. Setting Mode : 1280*720@60Hz
3. Pattern : Pattern #24 (Chess Pattern)
4. Use Equipment : CA210 & Master
MSPG925 Generator
Method of Color Calibration
(AV)
1) Apply the NTSC Lattice (N0. 3) pattern signal to the AV IN 1 port
2) Press the Source key to switch to “AV1” mode
3) Enter Service mode
4) Select the “Calibration” menu
5) Select the “AV Calibration” menu.
6) In “AV Calibration Off” status, press the “ > ” key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “AV Calibration” status from Failure to Success.
Method of Color Calibration (Component)
1) Apply the 720p Lattice (N0. 6) pattern signal to the Component IN 1 port
2) Press the Source key to switch to “Component1” mode
3) Enter Service mode
4) Select the “Calibration” menu
5) Select the “DTV Calibration” menu.
6) In “DTV (Component) Calibration Off” status, press the “ > ” key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “Comp Calibration” status from Failure to Success.
Method of Color Calibration (PC)
1) Apply the VESA XGA Lattice (N0. 21) pattern signal to the PC IN port
2) Press the Source key to switch to “PC” mode
3) Enter Service mode
4) Select the “Calibration” menu
5) Select the “PC Calibration” menu.
6) In “PC Calibration Off” status, press the “ > ” key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “PC Calibration” status from Failure to Success.
Method of Color Calibration (HDMI)
1) Apply the 720p Lattice (N0. 6) pattern signal to the HDMI1/DVI IN port
2) Press the Source key to switch to “HDMI1” mode
3) Enter Service mode
4) Select the “Calibration” menu
5) Select the “HDMI Calibration” menu.
6) In “HDMI Calibration Off” status, press the “ > ” key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “HDMI Calibration” status from Failure to Success.
1) Apply the NTSC Lattice (N0. 3) pattern signal to the AV IN 1 port
2) Press the Source key to switch to “AV1” mode
3) Enter Service mode
4) Select the “Calibration” menu
5) Select the “AV Calibration” menu.
6) In “AV Calibration Off” status, press the “ > ” key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “AV Calibration” status from Failure to Success.
Method of Color Calibration (Component)
1) Apply the 720p Lattice (N0. 6) pattern signal to the Component IN 1 port
2) Press the Source key to switch to “Component1” mode
3) Enter Service mode
4) Select the “Calibration” menu
5) Select the “DTV Calibration” menu.
6) In “DTV (Component) Calibration Off” status, press the “ > ” key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “Comp Calibration” status from Failure to Success.
Method of Color Calibration (PC)
1) Apply the VESA XGA Lattice (N0. 21) pattern signal to the PC IN port
2) Press the Source key to switch to “PC” mode
3) Enter Service mode
4) Select the “Calibration” menu
5) Select the “PC Calibration” menu.
6) In “PC Calibration Off” status, press the “ > ” key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “PC Calibration” status from Failure to Success.
Method of Color Calibration (HDMI)
1) Apply the 720p Lattice (N0. 6) pattern signal to the HDMI1/DVI IN port
2) Press the Source key to switch to “HDMI1” mode
3) Enter Service mode
4) Select the “Calibration” menu
5) Select the “HDMI Calibration” menu.
6) In “HDMI Calibration Off” status, press the “ > ” key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “HDMI Calibration” status from Failure to Success.
White Ratio (Balance)
Adjustment
1. You can adjust the white ratio in factory mode (1:Calibration, 3:White-Balance).
2.Since the adjustment value and the data value vary depending on the input source, you have to adjust these in CVBS, Component 1 and HDMI 1 modes.
3. The optimal values for each mode are configured by default.
It varies with Panel’s size and Specification.
# Equipment : CS-210
# Pattern: MIK K-7256 #92 “Flat W/B Pattern” as standard
# Use other equipment only after comparing the result with that of the Master equipment.
#Set Aging time : 60min
1. You can adjust the white ratio in factory mode (1:Calibration, 3:White-Balance).
2.Since the adjustment value and the data value vary depending on the input source, you have to adjust these in CVBS, Component 1 and HDMI 1 modes.
3. The optimal values for each mode are configured by default.
It varies with Panel’s size and Specification.
# Equipment : CS-210
# Pattern: MIK K-7256 #92 “Flat W/B Pattern” as standard
# Use other equipment only after comparing the result with that of the Master equipment.
#Set Aging time : 60min
Calibration and Manual setting for WB adjustment.
HDMI : Time #6 720P, Pattern #24 Chessboard Calibration > Manual adjustment #92 pattern (720p)
COMP: Time #6 720P, Pattern #24 Chessboard Calibration > Manual adjustment at #92 pattern (720p)
CVBS: Time #3 NTSC-J, Pattern #24 Chessboard Calibration > Manual adjustment at #92 pattern (NTSC)
PC: Time #21 1024*768, Pattern #24 Chessboard Calibration > Manual adjustment at #92 pattern (NTSC)
# If finishing in HDMI mode, adjustment coordinate is almost same in AV/COMP mode.
# White Balance Manual Adjustment
HDMI : Time #6 720P, Pattern #24 Chessboard Calibration > Manual adjustment #92 pattern (720p)
COMP: Time #6 720P, Pattern #24 Chessboard Calibration > Manual adjustment at #92 pattern (720p)
CVBS: Time #3 NTSC-J, Pattern #24 Chessboard Calibration > Manual adjustment at #92 pattern (NTSC)
PC: Time #21 1024*768, Pattern #24 Chessboard Calibration > Manual adjustment at #92 pattern (NTSC)
# If finishing in HDMI mode, adjustment coordinate is almost same in AV/COMP mode.
# White Balance Manual Adjustment
Adjustment Specification
White Balance : High light (±3), Low light (±5)
Luminance : High light (±0.1Ft/L), Low light (±0.1Ft/L)
White Balance : High light (±3), Low light (±5)
Luminance : High light (±0.1Ft/L), Low light (±0.1Ft/L)
Servicing Information
USB Download Method
Samsung may offer upgrades for TV’s firmware in the future. Please contact the Samsung to receive information about downloading upgrades and using a USB drive.
Upgrades will be possible by connecting a USB drive to the USB port located on located on the back of your TV.
Insert a USB drive containing the firmware upgrade into the wiselink port on the side of the TV. (USB drive make folder “T-CHE7IBRC” and this folder download micom program.)
Samsung may offer upgrades for TV’s firmware in the future. Please contact the Samsung to receive information about downloading upgrades and using a USB drive.
Upgrades will be possible by connecting a USB drive to the USB port located on located on the back of your TV.
Insert a USB drive containing the firmware upgrade into the wiselink port on the side of the TV. (USB drive make folder “T-CHE7IBRC” and this folder download micom program.)
2. Insert USB drive.
Menu > Support > Software Upgrade then press the ENTER button.
The message “Scanning for USB. It may take up to 30 seconds.” Please be careful to not disconnect the power or remove the USB drive while upgrade is being applied.
The message “Upgrade version XXXX to version XXXX ?
The system would be reset after upgrade.”
Press the left, right button to select “OK”.
The TV will shut off after completing the firmware upgrade.
Please check the firmware version after the upgrade is complete.
Menu > Support > Software Upgrade then press the ENTER button.
The message “Scanning for USB. It may take up to 30 seconds.” Please be careful to not disconnect the power or remove the USB drive while upgrade is being applied.
The message “Upgrade version XXXX to version XXXX ?
The system would be reset after upgrade.”
Press the left, right button to select “OK”.
The TV will shut off after completing the firmware upgrade.
Please check the firmware version after the upgrade is complete.
S/W Update method (JIG)
1. Connect Power & Uart cable to board
and Turn on the board.
2. Press [shift + ~] to enter uboot prompt.
2. Press [shift + ~] to enter uboot prompt.
3. Press any key to enter BOOTROM DEBUG
SESSION before timeout.
4. Make sure watchdog off.
If watchdog status is on then board will reboot after 15secs
If watchdog status is on then board will reboot after 15secs
5. Press “0”.
6. Save latest BSP images to /update folder
in usb memory.
7. Enter “bbm usb” after connecting usb
memory.
8. Press “1”.
9. Enter “u-boot.bin”.
10. Press “x” to return prompt menu.
11. Press [shift + ~] to enter uboot prompt
again.
12. Press any key to enter BOOTROM DEBUG
SESSION before timeout.
13. Press “0”.
14. Enter “bbm usb”.
* If there is not “a” option, Image is old
version or not updated. Then try again from No.1.
15. Enter “a”.
16. Enter directory path (if “/update/”is
right, just input Enter key).
It takes about 1 minute
17. Press “x”.
18. Enter “bbm show partition”
- Check partition status same as red box on picture below
- If different, go back to first phase. Do it all again!!!
- Check partition status same as red box on picture below
- If different, go back to first phase. Do it all again!!!
After this, if you want to update BSP image
except for partition format
Then just press “b”instead of 8 ~ 15
19. Turn off master power of TV and turn on and reset after prompt is shown.
20. Mount USB memory with next command.
# cd
# ls
Java mnt mtd_contents mtd_pers proc
bin mtd_acap mtd_down mtd_ram sbin
dev mtd_appdata mtd_drv mtd_rwarea sys
dtv mtd_boot mtd_epg mtd_swu usr
etc mtd_chmap mtd_exe mtd_tlib
lib mtd_cmmlib mtd_factory mtd_wiselink
#start_usb.sh
# cd dtv
# ls
usb
# cd usb
# ls
log sda
# cd sda
# ls
Autorun.inf T-CHL7DEUC update
T-CHL5DEUC photos.zip.exe
# cd update
# ls
Image exe.img oneboot.bin uboot_env.bin
Image_serial fnw.bin rootfs.img validinfo.txt
appdata.img info.txt serial_temp version_info.txt
boot.img onboot.bin u-boot.bin
21. Write ‘exe.img and appdata.img’.
fsrrestore /dev/bml0/8 exe.img;
fsrrestore /dev/bml0/9 appdata.img;
fsrrestore /dev/bml0/10 exe.img;
fsrrestore /dev/bml0/11 appdata.img;
Then just press “b”instead of 8 ~ 15
19. Turn off master power of TV and turn on and reset after prompt is shown.
20. Mount USB memory with next command.
# cd
# ls
Java mnt mtd_contents mtd_pers proc
bin mtd_acap mtd_down mtd_ram sbin
dev mtd_appdata mtd_drv mtd_rwarea sys
dtv mtd_boot mtd_epg mtd_swu usr
etc mtd_chmap mtd_exe mtd_tlib
lib mtd_cmmlib mtd_factory mtd_wiselink
#start_usb.sh
# cd dtv
# ls
usb
# cd usb
# ls
log sda
# cd sda
# ls
Autorun.inf T-CHL7DEUC update
T-CHL5DEUC photos.zip.exe
# cd update
# ls
Image exe.img oneboot.bin uboot_env.bin
Image_serial fnw.bin rootfs.img validinfo.txt
appdata.img info.txt serial_temp version_info.txt
boot.img onboot.bin u-boot.bin
21. Write ‘exe.img and appdata.img’.
fsrrestore /dev/bml0/8 exe.img;
fsrrestore /dev/bml0/9 appdata.img;
fsrrestore /dev/bml0/10 exe.img;
fsrrestore /dev/bml0/11 appdata.img;
