Indoor Unit - CS-E10KB4EA Outdoor Unit -CU-E10HBEA
Breakdown Self Diagnosis Function
Self Diagnosis Function (Three
Digits Alphanumeric Code)
# Once abnormality has occurred during operation, the unit will stop its operation, and Timer LED blinks.
# Although Timer LED goes off when power supply is turned off, if the unit is operated under a breakdown condition, the LED will light up again.
# In operation after breakdown repair, the Timer LED will no more blink. The last error code (abnormality) will be stored in IC memory.
# To make a diagnosis
1. Timer LED start to blink and the unit automatically stops the operation.
2. Press the CHECK button on the remote controller continuously for 5 seconds.
3. “- -” will be displayed on the remote controller display.
Note: Display only for “- -”. (No transmitting signal, no receiving sound and no Power LED blinking.)
4. Press the “TIMER” UP or DOWN button on the remote controller. The code “H00” (no abnormality) will be displayed and signal will be transmitted to the main unit.
5. Every press of the button (up or down) will increase abnormality numbers and transmit abnormality code signal to the main unit.
6. When the latest abnormality code on the main unit and code transmitted from the remote controller are matched, power LED will light up for 30 seconds and a beep sound (continuously for 4 seconds) will be heard. If no codes are matched, power LED will light up for 0.5 seconds and no sound will be heard.
7. The breakdown diagnosis mode will be canceled unless pressing the CHECK button continuously for 5 seconds or operation the unit for 30 seconds.
8. The LED will be off if the unit is turned off or the RESET button on the main unit is pressed.
# Once abnormality has occurred during operation, the unit will stop its operation, and Timer LED blinks.
# Although Timer LED goes off when power supply is turned off, if the unit is operated under a breakdown condition, the LED will light up again.
# In operation after breakdown repair, the Timer LED will no more blink. The last error code (abnormality) will be stored in IC memory.
# To make a diagnosis
1. Timer LED start to blink and the unit automatically stops the operation.
2. Press the CHECK button on the remote controller continuously for 5 seconds.
3. “- -” will be displayed on the remote controller display.
Note: Display only for “- -”. (No transmitting signal, no receiving sound and no Power LED blinking.)
4. Press the “TIMER” UP or DOWN button on the remote controller. The code “H00” (no abnormality) will be displayed and signal will be transmitted to the main unit.
5. Every press of the button (up or down) will increase abnormality numbers and transmit abnormality code signal to the main unit.
6. When the latest abnormality code on the main unit and code transmitted from the remote controller are matched, power LED will light up for 30 seconds and a beep sound (continuously for 4 seconds) will be heard. If no codes are matched, power LED will light up for 0.5 seconds and no sound will be heard.
7. The breakdown diagnosis mode will be canceled unless pressing the CHECK button continuously for 5 seconds or operation the unit for 30 seconds.
8. The LED will be off if the unit is turned off or the RESET button on the main unit is pressed.
To display memorized error
(Protective operation) status:
1. Turn power on.
2. Press the CHECK button on the remote controller continuously for 5 seconds.
3. “- -” will be displayed on the remote controller display.
Note: Display only for “- -”. (No transmitting signal, no receiving sound and no Power LED blinking.)
4. Press the “TIMER” UP or DOWN button on the remote controller. The code “H00” (no abnormality) will be displayed and signal will be transmitted to the main unit. The power LED lights up. If no abnormality is stored in the memory, three beeps sound will be heard.
5. Every press of the button (up or down) will increase abnormality numbers and transmit abnormality code signal to the main unit.
6. When the latest abnormality code on the main unit and code transmitted from the remote controller are matched, power LED will light up for 30 seconds and a beep sound (continuously for 4 seconds) will be heard. If no codes are matched, power LED will light up for 0.5 seconds and no sound will be heard.
7. The breakdown diagnosis mode will be canceled unless pressing the CHECK button continuously for 5 seconds or operating the unit for 30 seconds.
8. The same diagnosis can be repeated by turning power on again.
1. Turn power on.
2. Press the CHECK button on the remote controller continuously for 5 seconds.
3. “- -” will be displayed on the remote controller display.
Note: Display only for “- -”. (No transmitting signal, no receiving sound and no Power LED blinking.)
4. Press the “TIMER” UP or DOWN button on the remote controller. The code “H00” (no abnormality) will be displayed and signal will be transmitted to the main unit. The power LED lights up. If no abnormality is stored in the memory, three beeps sound will be heard.
5. Every press of the button (up or down) will increase abnormality numbers and transmit abnormality code signal to the main unit.
6. When the latest abnormality code on the main unit and code transmitted from the remote controller are matched, power LED will light up for 30 seconds and a beep sound (continuously for 4 seconds) will be heard. If no codes are matched, power LED will light up for 0.5 seconds and no sound will be heard.
7. The breakdown diagnosis mode will be canceled unless pressing the CHECK button continuously for 5 seconds or operating the unit for 30 seconds.
8. The same diagnosis can be repeated by turning power on again.
To clear memorized error
(Protective operation) status after
repair:
1. Turn power on (in standby condition).
2. Press the AUTO button for 5 seconds (A beep receiving sound) on the main unit to operate the unit at Forced Cooling Operation mode.
3. Press the CHECK button on the remote controller for about 1 second with a pointed object to transmit signal to main unit. A beep sound is heard from main unit and the data is cleared.
Temporary Operation (Depending on breakdown status)
1. Press the AUTO button (A beep receiving sound) on the main unit to operate the unit. (Remote control will become possible.)
2. The unit can temporarily be used until repaired.
1. Turn power on (in standby condition).
2. Press the AUTO button for 5 seconds (A beep receiving sound) on the main unit to operate the unit at Forced Cooling Operation mode.
3. Press the CHECK button on the remote controller for about 1 second with a pointed object to transmit signal to main unit. A beep sound is heard from main unit and the data is cleared.
Temporary Operation (Depending on breakdown status)
1. Press the AUTO button (A beep receiving sound) on the main unit to operate the unit. (Remote control will become possible.)
2. The unit can temporarily be used until repaired.
Error Codes Table
Diagnosis
display
|
Abnormality
/ Protection control
|
H00
|
No
abnormality detected
|
H11
|
Indoor
/ outdoor abnormal communication
|
H12
|
Connection
capability rank abnormal
|
H14
|
Indoor
intake air temperature sensor abnormality
|
H15
|
Outdoor
compressor temperature sensor abnormality
|
H16
|
Outdoor
Current Transformer open circuit
|
H19
|
Indoor
fan motor merchanism lock
|
H21
|
Indoor
float switch operation abnormal
|
H23
|
Indoor
heat exchanger temperature sensor 1 abnormality
|
H24
|
Indoor
heat exchanger temperature sensor 2 abnormality
|
H27
|
Outdoor
air temperature sensor abnormality
|
H28
|
Outdoor
heat exchanger temperature sensor abnormality
|
H30
|
Discharge
temperature sensor abnormality
|
H33
|
Indoor/Outdoor
wrong connection
|
H35
|
Indoor
drain water adverse current abnormal
|
H38
|
Indoor/Outdoor
mismatch
|
H97
|
Outdoor
Fan Motor lock abnormality
|
H98
|
Indoor
high pressure protection
|
H99
|
Indoor
heat exchanger anti-freezing protection
|
F11
|
Cooling
/ Heating cycle change over abnormality
|
F90
|
PFC
control
|
F91
|
Refrigeration
cycle abnormality
|
F93
|
Outdoor
compressor abnormal revolution
|
F95
|
Cool
high pressure protection
|
F96
|
IPM
(power transistor) overheating protection
|
F97
|
Outdoor
compressor overheating protection
|
F98
|
Total
running current protection
|
F99
|
Outdoor
Direct Current (DC) peak detection
|
